Liczymy pasujące modele…
Just print it with the filament type and color of choice. I used white PLA from the brand CST, which is a bit more flexible than other PLA I know. It's very sturdy, I use it with a light attached to an arm.
I got so annoyed with the pedals moving, so I created this two-piece mount. Originally posted by me on Thingiverse (https://www.thingiverse.com/thing:3230045), now moved here. Required: Four 20~3-mm M6 bolts, preferrable 2 of them with a…
Originally posted by me at https://www.thingiverse.com/thing:4236153 Probably the same fit as other Peugeot, Citroen, DS and maybe even Opel car models. I hope you still kept the springs! This one is a revised one. The pictures with the…
Why The hinges of the Playseat challenge are a bad design. They move from left to right. These pieces keep them in place. Printing instructions I printed in PLA+, but PETG would be better as it's more flexible. Print it standing up with a…
I use this pipe for ventilation of my FDM printer and my laser engraver. With the cap I can select if the printer or the engraver needs to be ventilated. See pictures Note that there are two mounts: one with 100mm outer diameter that fits…
An insert to store pencils for the world famous under desk drawer of @Paul_318082 https://www.printables.com/model/440401-under-desk-drawer-updated Print it with a material, color and layer height at will. Please acknowledge me by liking…
To convert my iMac Late 5K 2014 into a 5K monitor I used a Stonetasking R1811 driver board. Most of instructions here can be applied to other iMacs and other driver boards as well. Note, that my particular iMac is one with a factory VESA…
So I created this cap for the airtag keychain holder at https://www.printables.com/model/65525-airtag-strong-keyring-keychain-holder (and https://www.thingiverse.com/thing:4845981). The cap is glued to the airtag, so the airtag can still…
Introduction The original was posted by me at https://www.thingiverse.com/thing:3368589 but this one is a newer one. Models In the folder ‘original’ the files for the original are found. In the folder ‘With OBD opening and cover’ a…
I created this little calendar gimmick to remind myself it's Formula 1 race week! It around 10x10cm and can be printed flat with the default settings. Please note the F1 logo is not included so you need to search the web for it, please…
I printed the quick release part on a 0.6 nozzle with 0.35mm layer height just for the speed. 0.4 nozzle with 0.2mm would do fine too. The paddle part I printed with a 0.4mm nozzle with 0.15mm layer height, as the top is quite thin. I…
Prusa Bear toolbox (Bear? here: https://github.com/gregsaun/prusa_i3_bear_upgrade ) . Works with 20mm V-slots, doesn't really make use of the V-slot interface but has a snug fit. See pictures. Was originally posted by me at…
So, I use a volcano hotend on my MK3S Prusa Bear machine for years and decided to do some maintenance. I saw that my R4 extruder cover was melted. It also affected the (R4) extruder body, as the PINDA mounts was bend causing calibration…
Module Cases designed for RC2014 These are STL and SketchUp designs of module cases to be used on RC2014 or similar backplanes. I tried to mimic an 80s/90s era look & feel like MSX or Nintendo game cartridges. While working with it I got…
About The original model was created by me at https://www.thingiverse.com/thing:4296068 Why? The three most popular ways to steal your car is: 1) Intercept & extend the signal of your keyless-entry key 2) Take the VIN number and use that…
Chain cover I made this chain cover because when my daughter borrowed my bike her white (!) trousers got caught between the chain and the chainring. I never have this problem, but you know, fashion, wide trousers, that kind of stuff.…
RC2014 Backplane Pro Case “ RC2014 is a simple 8 bit Z80 based modular computer originally built to run Microsoft BASIC. It is inspired by the home built computers of the late 70s and computer revolution of the early 80s. ” - source:…
I created this quick release for the luggage carrier on an Engwe Engine X or Pro. May also work on other bikes, but not sure. At least it could be adapted. Works great with the Engwe 17-35L rack bag or Engwe 17L bag. But should work with…
So you spent a big portion of day to assemble an IKEA PAX closet, and then a while later you knocked out the rear plate by trying to fit something to big into it. It can happen to the greatest people. Instead of moving the closet from the…
MicroSD_tab_with_etxtra_flesh.stl This is a remix of Zsóka's microSD cards tab where I added more 'flesh' (an extra tab) to glue the microSD card on. This adds a little extra height, and it could be tight in some SD-card slots. Print…
I made this holder to fit a hygrometer I had lying around into a filament spool. It has a ~56mm outer diameter so it will not fit all spools. I used PLA-CF, but PETG is maybe a better choice, because more flexible. The window is 26mm x…
Summary I created a less rugged alternative headlight cover for this AliExpress headlight. https://www.aliexpress.com/item/1005004830554886.html Print Settings Supports: Yes Resolution: 0.2 Infill: 15% - 20% Filament material: PLA or PETG…
Playseat Challenge repair kit So your kids too tried to sit in the Playseat Challenge together? And now the tubes have folder at the hinge point? Yep, we've been there. This is our 3rd attempt to fix it. Before, we replaced it two times…
Summary I really like those Dopper drinking bottles, but they are a pain in the donkey to store. They always fall out of the cupboard when looking for something. This time it got out of hand and I drew myself something in Sketchup to put…
I found that the original spoolholder was a bit short for some of my spools. I made this one 15mm longer. Print in a material you like, but I wouldn't recommend TPU
I printed kjbturok's led frame (https://www.printables.com/model/271784-low-profile-led-frame-for-bambu-x1-and-others). But with my ledstrips the light was still very dim. Print a bunch of these, glue them into the ledframe and solder the…
Introduction Yeah, I know. You are not as stupid as me by pressing the brake pedal when the calliper was not mounted. And that's not the reason the cilinder came out of it, right? But still, you do have the same problem: you need to get…
This air tag holder will work with any surface that is 2mm thick. You just need to drill a 32mm hole. Printing instructions Print in TPU, 0.2mm layer height is fine A textured plate is preferred No need for supports Pro tip: dry your TPU…
To wszystkie aktualnie dostępne wyniki.
