20 modeli
Piper PA28 Aircraft all have 4 fresh air vents in the cockpit near the floor. They are very fragile vacuum formed plastic and easily damaged by peoples feet. I made the replacement parts in PETG. The two parts were redesigned slightly for…
I needed a case for 312 hearing aid batteries after Costco changed their battery packaging to a totally unusable design. This case holds 8 size 312 batteries with spring loaded friction arms. The screw on cap has a protrusion to push the…
Watering nozzle fits standard garden hose. Has very high flow rate for quick watering but gentle flow does not damage plants or flowers or disturb dirt. Spray holes are designed to spread water out. Can be put on a garden hose and also…
No-slam toilet seat hinges are subject to high stresses when the seat is quickly forced closed. This part replaces one of the hinge halves to salvage the seat. I used PETG but other materials might also work. Hexagon screw holes were used…
This design is from the USA Consumer Product Safety Commission. It is used to determine if a small part is a choking hazard to a child under 3 years old. Put the part into the tube and if it fits completely so that nothing protrudes past…
A large outlet funnel for use in kitchen, shop or garage. Most useful in the kitchen for transferring jelly, jam, fruit etc. to large mouth jars. Might want to use food safe material like PETG but other materials are suitable for non food…
Scotch Tape Dispenser Stiffener This part will transform a flimsy, unusable Scotch tape dispenser into a very usable piece. This part fits half inch tape. Pictures show dimensions of the dispenser that fits. The design is printed without…
Fidget Spinner I designed this spinner to recycle used roller blade bearings and entertain the neighbor kids. Put the best spinning bearing in the center location of this spinner. Bearings size: 20 mm outside diameter 8 mm inside diameter…
This torque wrench is printed from PETG. PLA can be used for some parts but the Rotors must be PETG. Six rotors provide torques of 0.5, 0.75, 1.0, 1.5, 2.0, and 2.5 Nm. The 0.25 inch square bar that connects the rotor to the socket can be…
Please find my newer revised design which makes supports much easier to remove. It is named "Long Handle Coffee Measure with easily removed supports" I printed in PETG but PLA should work fine. The part has a 45 degree chamfer on the base…
The flexible spout for my Eagle gasoline can split and is no longer available in the local hardware stores. I designed a new one with a plug on a lanyard. The 2 parts are made from flex, printed without supports at 0.20 mm layer height. I…
This easy to print part provides a place to hang a wash cloth for dripping and drying in the kitchen. Dimensions are provided to be sure it fits your sink. Slicer program could be used to adjust the dimensions to fit your sink too. I…
These toaster tongs should be printed from PETG without supports. Stiffness is optimized for PETG.
Watering nozzle fits a standard garden hose. This is a reduced size of my larger one for use on water systems that have limited pressure and flow. I have a larger design on “Printables” for more typical water systems named " Gentle High…
This design is for a Prusa MK4 was inspired by user MSB on Printables who made a design for the MK3. Why did I design this? I wasted 2 days trouble shooting bad prints only to discover I had a 0.6 nozzle installed but I had hardware and…
Rain Gage Float Improves visibility of water level in a rain gage. This model is solid, so print it with 5 perimeters 5 top and 5 bottom layers and no infill in PETG to get a hollow float. I use 0.20 mm layer height with a 0.40 mm nozzle.…
This Gilmour lawn sprinkler has a height adjustable ring to control the spray distance as the sprayer rotates so it can accommodate non-circular areas and avoid wasting water. After years of use, the ring (black) failed as shown in…
I printed in PETG but PLA should work fine. I have provided g-code for PETG and PLA for both the Prusa MK3S and Mini. The part has a 45 degree chamfer on the base which does not need supports but the handle does need them. I have…
Many Mercury 2-stroke outboard boat engines use a large oil tank. Mercury Sport Jet engines also use these tanks and Sea Doo boats used these Mercury jet drives for several years also. The cap can be difficult to remove or tighten if the…
Drapery Pulls I designed these parts so you could feel if you have the correct drapery cord end. These are especially useful for double layers of draperies as when a set of shear draperies is hung with another set. They are also useful…
To wszystkie aktualnie dostępne wyniki.
