Liczymy pasujące modele…
This is a thumb key for opening up your beer or carbonated beverage for rapid consumption. Please drink responsibly. Be sure to use a fairly high infill and several outlines for durability and longevity. Category: Kitchen & Dining
UPDATE (01/11/2022): I have added a curve to the bottom of the chute to better concentrate the pour from the hopper. In testing it has proven to be a noticeable improvement over the original. UPDATE (11/08/2021): I have added a new…
I had tried several other solutions for this, but decided in the end to make my own. These clip on just tight enough that you can pick up and move your chair without fear of the guards moving. There are two sizes, one for the side pieces,…
The adhesive on the Flic 2 buttons is great unless you have textured walls, like we do. No matter how many times we stuck the button to the wall, it just fell right off, so I made a wall mount for ours. There are two variations of two…
We play a lot of Flying Frog games and most of those games utilize a lot of card decks. In order to tidy up the decks on the table, I designed this deck stand. There's a 5-up stand and a 7-up stand, and they are designed with an offset so…
We needed to mount a bunch of Raspberry Pi units behind a series of TVs at work, so I designed a quick, slip-in cradle. It's just snug enough to hold the Canakit case securely, but loose enough to be able to get the Pi out and switch it…
I love Dice Miner, but I don't love how you have to take apart the mountain to make it fit back in the box, so I created a more compact version that works exactly as the original does, but it fits in the box with all other components,…
I loved the tile trays that @SenpaiCZ made for Mansions of Madness, but found that once I had printed enough trays to hold all of the tiles from the base game, all the expansions, and the legacy 1st Edition content, there wasn't any room…
I needed a cradle to hold an Apple TV on the back of our rolling carts so rather than using one with screw mounts, I designed one with a slip on tab. Designed to fit the AppleTV 4th Gen. The spacing for the rear tab is about 2mm, so it…
These card dividers are great for shallow boxes where the cards are stored horizontally. While this set was specifically designed for the Tales from the Loop board game, they could be used for most any game. Simply scale the divider up or…
We had some material from an old acrylic visor lying around, so I upcycled it into a splash guard for our Keurig K-Slim coffee maker. You can use pretty much any clear acrylic film for the splash guard. The groove for the acrylic is…
I loved the 7th Continent Discard tray by Aarcana, but I wanted to make it so that it could hold both the discard and the action deck. This was a quick clone and merge in Meshmixer. It has slots to hold the Discard insert on either side…
I liked how some of the 7th Continent player boards held the State cards vertically but I didn't want a full player board. I decided I could just make a standalone card stand for 80mm cards. The slots are wide enough to fit cards with…
NOTE: My first prototype was printed with PLA plastic and it has proven to lose its shape (and thus the tension) after a couple of uses due to the heat of the water/coffee. I am currently testing a new prototype printed with ABS plastic…
I noticed that the filament guides on my Lulzbot printers were getting chewed up being pulled into the extruder so I created a small cap to fit over the end of the nylon tubing. This provides a stronger end while also preventing it from…
This is a Decora switch cover that is also a Tradfri switch mount. This allows you to cover up your Decora rocker switch and mount an IKEA Tradfri switch directly to it. This is done using a magnet that is glued to the back of the switch…
I wanted to make some new boxes similar to the old plastic boxes that Moo used to ship with their Mini Cards. I improved upon the design by adding some thumb gaps to make getting the cards in and out easier. I did make the walls a bit…
The Paradox box had one surface that was too thin for my Lulzbot Taz 6 to render, so I extruded that wall out about a half mm. As a result, you will of course have to scale the lid accordingly. I simply expanded the Y-Axis of the lid an…
I sleeved all of my cards for Friday the 13th and they no longer fit in the original insert. the box is plenty large enough to hold the cards, but I missed having an insert. This was inspired by Game Trayz inserts with the routed channel…
To wszystkie aktualnie dostępne wyniki.
