30 modeli
Replacement strainer base for bilge pump used in boats. Recommending to print in PETG and with 30% infill. I used " The Filament ReFill PETG 1.75mm MACHINERY ORANGE 1kg (PETG, 1.75 mm, 1000 g, Orange) " with quite good results.
Wydruk około 1,78 €–2,18 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The original handle was glued on, and secured with two metal pegs from two sides. It is pretty hard to remove. The printed handle should be fixed with rivet and glue. Print it on PETG or ASA. No supports needed.
Wydruk około 1,47 €–1,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a MATE Compatible version of my ROV Kort Nozzle for Bilge Pump Thruster w/Integrated Mount. The New Rules for 2018 state.. (courtesy of MATE) 3.2.5 PropellersNew in 2018!!! *MECH -006: Propellers must be shrouded and have thruster…
This is a Kort Nozzle for a homemade ROV thruster made from a Mayfair 750 GPH Bilge Pump. Adding this kort nozzle to the thruster will increase the output thrust by about a full pound. This nozzle was specifically design to work with a 3…
This is a Kort Nozzle with integrated mount for a homemade ROV thruster made from a Mayfair 750 GPH Bilge Pump. Adding this kort nozzle to the thruster will increase the output thrust by about a full pound. This nozzle was specifically…
I made this to reduce my bilge 1 inch down to 3/4 inch. I suggest printing with PETG and using E6000, Shoegoo, or silicone to glue it to the pump. I used this for my powered sluice that I designed for the 30 inch ROYAL manufacturing…
Please give me feedback on how to improve this project ( and subsequently my skills :-) ). Description I needed a pump for my boat besides an electrical pump. If there is a problem with the power this pump will still operate. Base The…
You see that? That’s not a crab, and it’s sure as hell not human. A Bilge-Hulk Mauler is what happens when a sentient part of the land decides the shipyard scrapheap is his new wardrobe. They’ve grafted rusted boiler plates to their skin…
The Bilge Crab is basically a walking trash compactor with a bad attitude. They live in the slurry at the bottom of the hulls, feeding on rust, rot, and the occasional unlucky stowaway. Their shells are reinforced by the very scrap they…
This 3 pieces are part of the underwater robot we are building. They are use to join a 3/4" pipe with a bilge pump motor
This is a 1:100 scale hand operated bilge pump for the baltimore schooner Halcon 1840 wooden model boat kit. There are two versions to choose from: v1 - if you want to scale up this is more technically accurate particularly around the…
Made it as an example of one way of designing this connector. It's for a 19mm (3/4") inside diameter hose. Ended up in a boat later :) Migrated from youmagine.
22m pipe connecting to 25mm bigger pipe. Used to connect bilge water pump and manual pump hoses together. Especially in wooden boats you don't want to drill two holes to the boat so now you can survive with one. Design also includes 2…
I made a DIY solar heater using ½" dripline and 12v pump but output was not strong enough so switched to 1300 Tsunami bilge pump. The 1 1/8th outlet on the pump is not very standard so created this to adapt/connect to my ½" dripline.…
This is to replace the Seadoo part number 204050803 that cracked and crumbled. I went with PETG. First flat standard one. The other i made deeper so i could zip tie a charger cable in there and hide it when the back lid of boat is shut.…
This is a bilge pump adapter for the ECO-WORTHY 1100GPH 12V Marine Electric Bilge Pump that can adapt to a 10mm ID (Inner Diameter) ~3/8" hose. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA…
Created and shared in OnShape This is a replacement strainer (screen, filter, etc.) for an Invincible Marine 800 GPH Bilge pump with float switch . It probably also fits many other brands. There are two versions. One is just the strainer…
Tight fitting barbed hose (25mm) adapter for SeatoSummit manual bilge pump with filtered end to stop large debris https://seatosummit.com.au/products/solution-bilge-pump Category: Parts
filter for a hand powered bilge pump, 2,5 mm holes and one 5,5 mm. hole for the tube to slide in
This is the bilge pusher for a solo sprayer (I believe part number 40-74-233). Print Settings Printer Brand: Formlabs Printer: Formlabs Form 2 Rafts: No Supports: No Resolution: 100 Infill: 38 Filament: Formlabs Grey Pro Grey Notes: The…
Dies ist ein Gehäuse für den Geekom MiniPC A5 mit dem einsteckmaßen 117x112x39 mm, habe es für mein Wohnmobil entworfen, es kann aber überall montiert werden. In der dargestellten Form ist es ohne Probleme Druckbar. Hoffe ihr habt auch…
This just holds it down 3 Perimeters, 3 Top & Bottom layers, 10% infill Pump https://smile.amazon.com/gp/product/B01LZ5HQ2W/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Used Dual Lock to Mount…
Requires you print 2x clips that you glue in after. This is to reduce flimsiness
Simple model to allow me to connect my little 12v bilge pump (20mm connector) to my caravan sullage hose 29.5mm connector). This allows me to recirc warm water with detergent through my sullage pipe to flush out debris from the pipe. I…
If using a whale gulper bilge pump, this can be your pickup.
This was custom-made for live well water supply. Cut the 19 mm hose barb section and attach it with adhesive
I designed a simple cup around the shape of the pole vault box to maximize the amount of water removed in each use.
A friend had a vintage boat with a manual bilge pump. The original “Head” was made out of a hard rubber, it had deteriorated beyond repair. And there were no replacement parts available. There is a flare at the top of the brass body so I…
Bilgepumpengehäuse für Boote als Ersatzteil zum Drucken oder Fräsen
There are some bilge pumps with a fragile protective mesh mounted on bottom which also serves a function of mounting plate (pump is mounted to boat's bilge - the lowest inner part of a ship or boat's hull where water collects). The…
