650 modeli
Remixed and improved Phone stand for VW Passat B6 Bluetooth by: Adrian-Claudiu Bîcleșanu Changes of this remix Sacrificial layer for better print of holes for screws on the base bracket Redesigned left/right and down bracket Bigger holes…
Tap is a bluetooth dual switch access device that enables people with disabilities to control mobile phones, tablets and computers. It works by activating switch control on the selected device, and mapping Tap’s customisable buttons to…
Since phones have no longer mini jacks it is hard to get music from the phone into a mixer channel. This bluetooth module has a mini jack that fits into any audio system, but it’s designed for MackPro mixers that have a mini jack input on…
My JBL 3 flip Bluetooth speaker can either be standing on my desk or laying flat if I have enough space (which does not happen a lot!) so it is usually standing. But in this configuration one of the woofers is facing the desk which is not…
Printing: No supports needed. This can be printed in a wide variety of materials. Purchase: Also available at kytor.com/store/product/n64-controller-display-stand/ Recommended Materials: PLA MAX Light Gray DURAMIC 3D PLA Plus Black or…
Build a 3D printed Bluetooth speaker, inspired by the TV Show Severance. Powered by the Feather ESP32 V2 and the MAX98357A 3W I2S amplifier. This project is written in Arduino and uses two libraries by Phil Schatzmann that make using the…
This is remixed from Stefan's holder for the ProFlight 2 to fit over the headset clip in the Airbus A320 series (possibly other Airbus models that share this clip?). This version also adds a headset hanger. Print upright (with the cable…
SUMMARY I designed this Bluetooth speaker in the Fall of 2020. I am NOT an audio engineer, nor did I have much knowledge about what I was doing from an acoustics point of view. But it still turned out great and sounds amazing. There is no…
LCM Nearfield monitor speaker This is a near field mini-monitor, designed for excellent bass response, and intended for use at a desk or console. They are suitable for desktop, shelf, or wall mounting and optimized for small to medium…
This is an under desk, under shelf or wall mount you can use with the Bluetooth 2.1 Amp ZK-TB21 that I purchased from Amazon. I built mine with the included metal casing on the amp as well, but I guess you could leave that off if you…
Welcome to the Tiny John! Inspired by the massive, room-dominating "Big John" horn setups taking over the audiophile world, I wanted to engineer that same dramatic acoustic presence into an affordable and desktop-friendly form factor.…
3D MODEL DESCRIPTION It is the funny bluetooth car, that overcomes small paper boxes. You need just 3D printer, Arduino, phone, 5V power bank and 4 ballpoint pen! Step-By-Step user guides: EN: here CZ: zde Parts list: here Main…
My first completely original model! This is an Ikea Skadis mount for the Nintendo Switch Online Super Nintendo (SNES) or Super Famicom (SFC) bluetooth wireless controller. It will also work with the 8bitdo SN30 or SF30 bluetooth/2.4ghz…
electronic part usb mp3 radio bluetooth Module pam8403 Amplifier Module tp4056 Module USB Battery Charger Board lithium ion battery speaker on off switch mask.stl is optional for protect speaker print infill 30% no top no bottom
At its core is the main speaker - everything is contained in the main box including the Lithium Ion batteries, recharging circuit, bluetooth receiver and amp. You'll also find both a standard USB and USB C port to re-charge your other…
I designed a custom mod phone stand for my VW Passat B6 bluetooth stand, the measurements are for my phone - Samsung Galaxy A70 with protective cover but it can be suitable for other phones with same size or bigger, can be adjusted. I…
Version 2.0 files available! Key differences: M3 mounting points for a more sleek printed handle at the top of the speaker Barrel jack for power and mounting points for a battery holder at the back JAB4 now mounts to the access panel for…
My another version of AAA battery case for Xiaomi Bluetooth/Zigbee thermometer. This variant arranges batteries on the sides so the whole thing has a slimmer shape better suitable for wall mounting. The case is designed to be printed…
I've built a case for my pcb that holds 1 esp32 and 2 nrf24l01+pa+lna I've attached photos so the exact placement of the esp32 and 2 nrf chips can be seen. The case also have 2 holes to store the antennas safely. The case have a small…
This is designed to display your Nintendo Switch Online edition SEGA Genesis Control Pad and a Genesis / Mega Drive Bluetooth adapter such as the 8BitDo Retro Receiver or the Retro-Bit Bluetooth Receiver . Printing: No supports needed.…
Adapter passt sehr gut in die originale Halterung für den BT-Adapter. Hier ist es eine Halterung für das S23 Ultra geworden. Die einzelne Grundelemente lassen sich an jeweils das Eigene anpassen. Zum Drucken habe ich hier PETG verwendet…
I made a mini case to this Bluetooth Audio Receiver: https://www.aliexpress.com/item/1005002231624213.html
Seeing how smart espresso or coffee scales can cost hundreds of dollars, I decided to build my own. I designed all of the 3D files and created a companion web-app that runs in any browser that supports the Bluetooth API (Chrome would be…
This is modified version of Valentin's scale to fit on my Breville Dual Boiler espresso machine. An ESP32-based Feather board is used in place of the ESP32 Thing of the original. This board from EzSBC.com vastly reduces the original…
If you found my things useful, you can buy me a cup of coffee: http://paypal.me/marcuss24 3D view: https://a360.co/3cZkVxu You have to print twice these parts: Battery holder - cable holes.stl Passive Holder.stl Screws: 8x M3x12mm Flat…
Für den Xiaomi Mijia Bluetooth Thermomether/Hygrometer habe ich eine Wandhalterung konstruiert. Da dem Gerät nur ein doppelseitiges Klebepad beiliegt und keine weiteren Befestigungsmöglichkeiten vorgesehen sind, könnte es bei einem…
Those little Bluetooth thermometers from Xiaomi can be flashed with custom firmware to turn them into Zigbee devices. But Zigbee implementation consumes a bit more power and a small CR2032 battery may not last too long. This model…
This is a 3D Printable model of a Fallout 4 Mini Nuke which has provision for a Bluetooth speaker and RGB lighting in a translucent top that can be used as a nightlight or just as a display piece. Re-Mix Notes The Fallout 4 Mini Nuke…
This is the "generic" version of the holder where I've left the cutout for where the USB-C prong fits through the bottom to charge the ring. However since everyone's USB-C cables are different you'll need to customize the rest of the…
Body for cheap MP3 Bluetooth FM player body (small size) from Aliexpress.
Remix of Aibot's Portal Radio on MMF, with some quality of life features and changes. I added a rear hole for a usb-c port in the base, and some more space under the ark led for cable management. The antenna holder has a bottom to it now,…
Mount a ESP-WROOM-32 on top of the heatsink of Nintendo 64 mainboards. Be sure to use PETG for flexibility and heat resistance.
These bluetooth headphones look great, sound awesome and can be built using 3D printed and cheap, readily available parts. They have volume +/-, track skip/back, play/pause buttons and a microphone to take calls. To build them you need a…
There are 2 models. One with 20 degree angle and another one with 30 degree angle. The 30 degree one is a bit bigger. Print No infill No bottom or top layers 4 wall layers
Deutsch: Ich habe mein Modell des iPod Cases modifiziert, um ein paar weitere Features zu bieten: einfacher zu drucken (bzw. Supports zu lösen im Vergleich zu meinen vorherigen Cases) Platz für den UGreen Bluetooth Sender MagSafe…
Bluetooth Audio Receiver case for BLE Audio Receiver module with black PCB.
A 3D-printable housing for the MyScale KP20488 bluetooth scale (~15 EUR on AliExpress). Designed to fit on the Gaggia Classic drip tray while maintaining bluetooth connectivity for Gaggiuino and Gaggimate integration. The model transfers…
Uses the screws and spacers that came with the amplifier board kit. Steps to assemble: 1. First prepare the top part by fastening the spacers with 4 screws on it. 2. Place the board into the bottom of the enclosure 3. Slide the top part…
This is 3D printed variant of https://www.instructables.com/Portable-Bluetooth-Speaker-Made-From-Scrap-Wood/. You can follow the same guide because enclosures are almost identical (i used same dimensions). Two holes on front side are for…
This is a small remix of this model which was almost what I needed but not quite. I have a camper van with Adventure Wagon L-track on the walls, and I wanted a way to mount my Anker Soundcore bluetooth speaker to the L-track. I modified…
Travel guitar with integrated effect device and power bank. Headless and full scale 628mm. Suitable for E-Gitarrenbausatz Single Cut and pocket pod effect device. Guitar 1 also has a low-latency Bluetooth transmitter for direct…
Find the info and bill of materials here: https://printkits.com/blogs/news/july-mini-boombox
A large 3D Printed bluetooth speaker. It sounds pretty good, and can be made for less than $150 including all the printer filament. Video about my speaker build project is here: https://youtu.be/zxz6ExM55y8 You can hear an audio demo…
Hi, I have constructed my version of Xiaomi Mijia Bluetooth Thermometer Hygrometer bracket for my SAMLA drybox. It is also compatible with cheap popular chineese noname thermometer/ hygrometer. Just print, use double-sided tape and stick…
A small stand that angles a small bluetooth speaker towards your face for better sound.
I always wanted to have a bluetooth speaker. I thought, why not design and build one. So here it is. This bluetooth speaker contains two rechargeable 18650 battery's, so you have lots of listening fun without plugging it in your…
my own design inspired by the Gravastar Mars 500$ speaker. works with a small wireless speaker that fit inside. entirely designed and created by MiaouCat! i am using a SoundCore Mini Material needed: all the 3D printed part. (3X foot) a…
This is my DIY bluetooth speaker with optional Aux input, made from 5.5mm acrylic, aluminum extrusion, and 3d printed parts. The overall cost came out right about $185 (Though some items like bolts, etc... were bought in bulk to save…
Bluetooth Keycap printed with Blue and White
i needed a way to fix this shutter to the printer, as slick and nice looking the ender 3 s1 is, there arent any easy ways to fix it but i think i managed to create something useful. WHAT TO PRINT: you will have to print the mount…
Designed to print on a E3D BigBox width: 290mm height: 206mm depth: 191mm Speaker hole spacing: 136mm diagonal Took 40 hours to print at 50mm/s base speed 0.3mm layer height Used about 500g of filament Supports needed Print Settings…
I didn't like DJI's solution of attaching the remote control to the handlebars of my bike using the strap. It was too cumbersome and always got twisted when operating it. That's why I designed this very simple holder that can be attached…
Housing for audio bluetooth module VHM-314 (comes with red or black pcb). Two part print, supposed to be snug fit, but it depends on the printer. Should print fine without supports. Assembly with 2x M2x4mm screws (i simply took any length…
This case is for XY-BT Mini Bluetooth module with micro USB port. The layer height for the printed model is 0.2mm and it is printed with premium ABS material. No support is needed for printing. For better placement of the module in the…
I wanted to clean up my desk and replace my huge speaker boxes with stylish and tiny new ones. After gathering a few impressions from other projects, I started to design this tiny spherical speaker box for my desk. The design (size,…
This is a simrig holder for the famous Nobsound NS-01G PRO Mini Bluetooth 5.0 Digital Power Amplifier. This Amp is quite commonly used für bass shakers. Link to the amplifier: https://amzn.to/4ucmMGd * Reccomended settings 0.16mm layer…
I designed and 3D printed Wave Mini, my own bluetooth speaker. The design was done in Autodesk Fusion 360 and the Rockler Single Wireless Speaker Kit was used for the electronics. The design was fairly basic and consisted of 3 main…
just replace M3*6 to M3*8 For https://www.printables.com/model/356301-arc-for-bambu-lab-p1p You can also make it for X1 or other one
Samsung Bluetooth remote wall mounted holder. Fits Samsung Bluetooth remotes on TVs from 2020 onwards. Print at 0.20
Bose Soundlink Flex SE Bluetooth Speaker Wall Mount
To mount the BT dongle of my Daly BMS, I made a holder that also holds the USB plug in place. It fits tight (depending on printer tolerances of course) - but it should be a one-time thing - so I like it. Maybe scale it up by 1% or so if…
The rear “actuator” plate behind the D-pad on the Retro-Bit Sega Saturn Wireless / Bluetooth controllers is known to crack , when this happens that particular directional will be inoperative. Printing: Print in PETG or PC. Note: PLA, ABS,…
Basic 3D printable enclosure for Rockler Woodworking's bluetooth speaker kit.…
Speakers produce much better sound when they are facing towards the listeners, so I created this simple angled stand for my SRS-XB13.
LaskaKit Sound DIY 3W Bluetooth Reproduktor Jedná se o malý jednoduchý 3W Bluetooth reproduktor, který můžete vytisknout a sestavit. Posledních několik měsíců jsem pracoval na designu a hardwaru, vyzkoušel jsem spoustu reproduktorů a…
This mod is janky. Do not attempt this if you don't feel at least decently comfortable with using a soldering iron near your iPod's parts. Here's my attempt at designing an iPod back case replacement that allows for Bluetooth…
A wall mount for GL-S10 bluetooth gateway serving as an ethernet esphome bluetooth proxy for Home Assistant, remixed from the original AR300M wall holder with an additional BT icon inlay for fun Guide on configuring it as a bluetooth…
English: This small housing encloses a Bluetooth remote control ( Festool CT-FI ) for vacuum cleaners from Festool and allows mounting them on the wall, which are actually intended for mounting on a suction hose. The housing has two holes…
I designed this case that's inspired by visual futurist artist like Syd Mead and John Eaves. Not your typical boxy type case for a piece of audiophile equipment. This is meant to make it standalone and have a visual impact with futuristic…
Great news. I have just finished designing and printing a very cool charge adaptor for the track loader. It will be available within the next couple of days. The Charger can be found here: https://www.thingiverse.com/thing:2794970 I'm…
This is a tiny Bluetooth speaker system designed as a "kitchen speaker". Assembly requires following parts and a bit of soldering. 1 x Bluetooth Receiver: TinySine Bluetooth Receiver Board @Amazon. 1 x Amplifier: Adafruit Stereo 3.7W…
This is a mount to hold a bluetooth speaker on the front of a Seadoo Spark. I designed around a JBL charge4 but it should work for just about any small or medium sized bluetooth speaker. Mounts with three m4x35 screws and three m4 nuts.…
Make a custom wireless gamepad with Cherry MX Switches! In this project, we'll build a custom PCB for Cherry MX switches and the Adafruit Feather 32u4 Bluefruit LE to make a custom gamepad. We'll design and 3D print an enclosure and…
I recently picked up the ESP32 based OpenTherm Smart Thermostat kit from DIYLess ( https://diyless.com/product/opentherm-thermostat ) as a cheaper alternative to a brand name smart thermostat. It came with a Xiaomi Mijia Bluetooth…
This is variant of https://www.instructables.com/Portable-Bluetooth-Speaker-Made-From-Scrap-Wood/. You can follow the same guide, but instead of using battery and step up module you need step down module. This speaker is made with 5V…
How to 3D print and assemble your very own programmable and remote controllable automatic domino laying machine. Who likes knocking down absurdly long runs of dominoes? I do. Who doesn't like laying them all by hand. I don't. That's why I…
Xiaomi Temperature and Humidity Bluetooth Sensor (Hygrometer) Holder for Ace Pro Print with PETG + supported
I needed a rechargeable speaker in my basement when I do sports. Parts you need for the build : TDA7492P 50W+50W Wireless Bluetooth 4.0 Audio Receiver Digital Amplifier Board : https://www.ebay.fr/itm/263033357309 2" inch 8Ω 5W Speaker…
shell for Bluetooth 5.0 MP3 Decoder Board Audio Module USB AUX TF FM Radio similar to this one https://www.ebay.com/itm/Bluetooth-5-0-MP3-Decoder-Board-Audio-Module-USB-AUX-TF-FM-Radio-for-Car-Auto/284075358449 i had no 2.5mm screws so i…
This speaker is the second generation of my original 3d printed and acrylic bluetooth speaker, but this time I wanted to power it from either a power supply or my Dewalt 20 volt batteries. Initially, I thought of using the Power Wheels…
BlueRetro is an open source project that allows you to use modern Bluetooth based controllers on retro consoles. Find out more at the Github and Hackaday sites. This case will hold a BlueRetro build using a ESP32 mounted on a 60x40mm…
BT201 Bluetooth mp3 audio module case added LEDs to the speaker output and a 47Ω resister the LEDs blink to the Music looks cool. The case snaps together put small dab of hot glue on the back corners to hold board in place do not over do…
Govee Hygrometer (H5075) Magnetic Mount (12x3mm Magnets) For mounting Bluetooth connected Hygrometer in printer, drybox, etc. H5075 keeps history so you can keep track of dry box humidity and temperatures over time. No support Press the…
Hier findet ihr einen Halter zur Befestigung eines Fingerbot Plus am Bedienfeld einer Steinbach Wärmepumpe mini. Den passenden Fingerbot findet ihr hier:…
Makerdiary sell an nRF52840 dongle for Bluetooth development. I bought one without a case, but I should have really got the one with a case. No matter, I have a 3D printer. It's best printed in white, so that the LEDs can shine through…
DIY 3D Printed Bluetooth Speaker 🔧 Note: This project is still a work in progress. Perfect for makers and DIY enthusiasts who want a custom, functional speaker with a 3D printed enclosure. Video: Parts included in STL files: Box Lid…
Note: This is a remix. Download the other parts here: https://www.printables.com/model/74032-formula-b1-remix-arduino-pro-micro In addition to what you need in the original model, you may need: 1x ESP32 with Bluetooth (CH340C 30pins…
I made 3D printed, Bluetooth connected, game show buzzers for playing The Voice at home, powered by Adafruit Circuit Playground Bluefruit boards and a laptop. Find the full story including build instructions in my blog post . Here it is…
Foot pedal frame to house a Logitech M650 mouse, creating a wireless silent foot pedal for spamming left click (OSRS) The retaining “nubs” aren't exactly secure for the mouse but the mouse is very unlikely to come loose from the pedal…
I found on AliExpress amplifier for 100CZK and realise that i had some speakers from old sony radio. And new project was started… Speakers are 1x 78mm and 2x 100mm Amplifier is from Ali there are more of them but just to check ohms my is…
Este soporte para altavoz bluetooth evitara que salga rodando y se nos caiga. En concreto es para un altavoz de marca Rienok.
LaskaKit ESP32-C6-DEVKit WiFi 6, Bluetooth 5, Zigbee 3D model vývojového kitu LaskaKit ESP32-C6-DEVKit WiFi 6, Bluetooth 5, Zigbee Stránka produktu: https://www.laskakit.cz/laskakit-esp32-c6-devkit-wifi-6--bluetooth-5--zigbee Github:…
I lost the battery cover for my wireless mouse and got tired of the battery and USB receiver falling out. The cover is a pressure fit and is a little difficult to take off. I recommend printing in PETG. PLA tends to deform over time. Also…
Introduction We all know that carrying full, heavy watering cans, buckets or hoses is a boring job that only causes back pain. Because I have to water a lot of flowers in my garden I decided to find a solution to this problem. After…
Body for cheap MP3 Bluetooth FM player body (medium size) from Aliexpress.
Some folks who market a bunch of expensive products believe that vibrating your guitar a bunch will improve its “tone”, whatever that is. Here's a mount that you can attach to an EWA106 bluetooth speaker to put that to the test and maybe…
Xiaomi Mijia Bluetooth Thermometer / Hygrometer is an extremely cheap Bluetooth low-energy thermometer and hygrometer. (Approx GBP5 each). These can be monitored automatically by listening for the BLE advertisments. I recommend using the…
You can find the BT5.0 Audio Pro card on the internet. It is 36x38 mm and has an amazing lot of possibilities. I paid € 4,25 for it. As I needed to connect my new jackless phone to the old audio system in the workshop, I only wanted the…
Purchase: Also available at kytor.com/store Recommended Materials: DURAMIC 3D PLA Plus Gray or Black Printing: 0.4mm nozzle, 0.2mm height, 15%+ infill, 2+ walls No brim or supports necessary Variants: -00 Single Controller Stand Revision…
Built on the foundation of the FDM4, the FDMDuos deliver stronger low-end performance with enhanced output below 100 Hz. If you like a little junk in the trunk, these bad boys are for you. They still carry the top end sparkle of the…
