119 modeli
The diameter of the retaining circle is 70.82mm. The fixing holes are 5mm. In the photos I fixed the support temporarily with Patafix / Blu-Tack Print in PLA, 0,15mm, with support
Wydruk około 3,25 €–3,97 € nettoWstępna wycena jednego wariantu
ENGLISH … I want to share with you a 1:10 scale body model of the Land Rover 3 Series (III). The wheelbase is 229-230 mm. Body width 170mm. The front fenders, doors and rear fenders are connected using 3 pieces of carbon rods with a…
This design is based on spacing points as equally as possible on a sphere (using charge-like relaxation optimization) and then cutting planar slices perpendicular to those directions. This make fairest as possible dice for any number…
The VOID9 Macropad is a handwired 3x3 pad that uses a Pro Micro as a controller. Two versions for the top case are included, one of them is flat, the other has a 4mm fillet. There are two versions for the bottom case as well, a flat one,…
MN90/99 D90 Rear Roll Bar with and without tire carrier. You'll need to get quite a bit of support for this to all work; but it turned out really well. Both options are included in the file. You'll need 2 x M2 15mm or better to hold the…
A simple knob replacement for the Philips HD9200 Airfryer. Designed to fit the timer knob, but I think it would also fit the temperature knob. I used a sharpie to put marks at the 10-minute intervals. With the knob installed, the 0-minute…
Sleeve for extended XD9 magazines. Designed to fit AWCY?'s XD9. Tab'd version has a removal tab on the back to help with printing the sloped edge.
I had this second hand gas heater, the Truma E2400, but this part was missing and it appears to be smaller in diameter than the spare parts you can buy …. So I designed one (from pictures & measurement of the parts you screw it on) and…
This model is inspired by the babyphone mount by Bosal. A solution to mount the babyphone of a friend at bed. I created the part from scratch to add the following features: The edge of the bed is 20.5mm wide: easy… Screwing the M6 without…
As often in cheap crawler kits, the required steering parts for a proportional servo are not included. The suspension could be better as well. Ans of course, some tuning parts are always nice. So this thing includes: Servo clamp Improved…
WIP - MN90 D90 Front Battery Expansion ("frunk"). The stock part doesn't allow for any good size battery or after market electronics. So I created a set of 3 parts to make it all work. All holes (minus the M3 hole) are sized at 1.95mm so…
Designed for 0.1mm layer height (0.2mm first layer height is fine). No supports required. Use 1mm thick double-sided tape pieces UPDATE: added BSP D9 version with +0.4mm clearance
THERE IS MORE TO COME - photos and instructions. NOTE: I accidentally included some redundant files: "Body A", "Body B" and "Body C" are identical to "Long Hood Section A", "Long Hood Section B" and "Long Hood Section C". All I did was…
The ribs on the circumference make the knobs less slippery. The original knobs are easy to remove. Help with a spatula. The steel leaf springs of the original knobs must also be used in the printed knobs. Fit the knobs so that the leaf…
Germany’s Next Topmodel 1941 and Luftwaffe's best workhorse. My favourite German WW2 fighterplane. Designed by Kurt Tank. Use Paperclips for the struts. https://en.wikipedia.org/wiki/Focke-Wulf_Fw_190 3D-Dora Model:…
MN90/99 front chassis plate upgrade. No mods to the stock chassis rails are needed. Uses only 11 grams of plastic when printed at 0.2 and 20% infill. The stock screws for mounting the body can be used. This chassis plate requires a 17g or…
MN90/99 rear chassis plate upgrade. Uses 4 x M3 screws (8mm or 10mm will work). No mods to the stock chassis rails are needed. Uses only 11.4 grams of plastic when printed at 0.2 and 15% infill. The stock screws into the body posts…
die hinteren Fender angepasst. the rear fenders adjusted.
***Had to name it in this wierd way, because Glock is very protective of its name. I should've expected this beforehand, the biggest producer of ...."Horse milk".... will be a bit awkward when its about reading his own name. "Big Stick" -…
General Description Most parts marked L and R for left and right. LR parts fit or must fit both sides. However, some parts need to be mirrored in the slicer. Almost all holes are designed for M3 screws. Sometimes nuts are needed, but…
These 3D printable files are designed specifically for storing bobbins from the Janome HD9 v.2 . The bobbins for this machine are larger than standard household machine bobbins. (Edit: There was a small mistake in the first version of the…
Philips Air Fryer HD9252 Microswitch shaft. This plastic shaft is located on the right side of the basket and it's needed to actually start the air fryer program. Original part of my model broke making the whole air fryer useless. To…
Mount for side protectors for honda crx ed9/ee8 Reverse engineered from (probably) orginal mounts in side mounts for front fender. It work quite well in my case Dont look at print quality of my version - i had quite wet filament at that…
Simple clip mount for SCD923. Uses M3 thread inserts so clip can be changed to different mounting option
Reinforcement and Wheelholder for Tamiya Land Rover Defender D90. Replaces the polycarbonat pieces “rear brace A” and “rear brace B” (instructions page 15, step 30). Drill holes and use double-sided tape as described in the instructions.…
These are designed to replace the unobtainable MD998761 special service tools to install the camshaft oil seals for a 6G72 (Mitsubishi 3000GT, Dodge Stealth, etc…) Specifically designed from measurements taken off of original,…
Took my JetBD920 fan blade cover off to clean out any chips and found a broken blade. The whole fan was just rotten plastic. This is the replacement I drew up in Fusion360 Category: Machine Tools
Babyphone Halterung Philips Avent 2-Teilig mit einstellbarem Winkel. Zusatzmaterial: M6x25 (Innensechskant) / M6-Mutter Die Klemmplatte hat eine Aussparung von 17mm, kann nach belieben angepasst werden.
Rear Magnetic Body Mount kit with option for an extra enforcement. Allows for the rear body mounts to be magnetic only or use the stock screws into the existing supports. Does require you remove (if present) the one extra stand-off on the…
This is an enclosure for a Waveform / Signal Generator built with an Arduino Pro Mini or Nano (ATmega 168 is sufficient) and an AD9833 Programmable Waveform Generator. One 18650 Battery can be fitted inside the case together with charging…
Description D9 Arrow is a slim 3D printed model rocket designed around D-class model rocket motors, with a focus on stable flight, clean aerodynamics and simple assembly. The rocket has been designed and simulated in OpenRocket , with the…
Ipad9 TouchChat word power 60 PureSense Case keyguard attaches with micro sucation tape
I have recreated the beautiful Porsche Design90 rims, also known as D90, for the modification of the low poly Porsche 991 Turbo. These fit the V2.1 tyres of the remix and are installed in the same way. Porsche Model:…
I made this so I can use the printable Miele tools on my Electrolux Pure D9 which has a non-standard shape. Adapter fits over the Electrolux hose and under the Miele tools. Miele tools: https://www.thingiverse.com/miele_3d4u/designs
I needed more desk space and thought of mounting topping D90 stack under the table like @lucasratmundo posted here https://www.thingiverse.com/thing:4731244 but his design needs a bigger printer and couldn't print it on Mk3s. So, i…
Hammer drill DCD999 Impact driver DCF850 Battery charger DCB1104 Screwdriving bit set DWAUMF30SET Drill bit set DWA1180
Well I finally looked first for these gears in Thingiverse instead of blasting away and drawing them myself. Unfortunately no one has seen the need so here I go. A link to the Fusion360 project is here / https://a360.co/2MmJPNo I needed…
VERSION 4 now!! - Custom Cooling duct for Wanhao Duplicator D9. Cleaned up the design, lowered the duct holes below nozzle Working perfectly well compared to stock.. Please post the feedback how you liked it or if any improvements. NOTE:…
This model is the bezel for this beautiful monitor. it's really hard to find original one and could be quite expensive.
Cloud9 Logo and Keychain You can print multi color keychain with a single nozzle (use this video for reference) or using multiple extruders, palette, etc. I also add a design for dual color logo and keychain, just use Cura's pause at…
Here's the result of uncountable iterations of trying to improve the part-cooling fan that comes with the Wanhao Duplicator D9 (MKII 400). It's supposed to fit the original 4010 fan without the need of disassembling anything. Just use 2x…
Für den CRX ED9 habe ich einen Halter für die Sonnenblende entworfen. hab ihn mit TPU gedruckt und 25% Füllung. Nach dem Druck ist noch etwas an Nachbearbeitung notwendig da die TPU Stützen recht bescheiden zum wegmachen sin und die…
Credits MirageC Initial work and for designing this awsome Printer
Additional Parts needed 1x Bahar Enclosure 150*140*70mm project box 1x C-Control Pro Nr. 197220 SD card module 1x MeanWell RS-15-5 PSU 1x CBM D9069 PetSD+ variant board ( https://github.com/InsaneDruid/CBM-D9096/ ) 2x 5mm LED (one red,…
I recently added a NanoELS H4 https://kachurovskiy.com/ controller to my JETBD920N lathe. I already had a Z axis motor mounted for an ELS but needed to add a X axis motor. Maxim has a great design for a smaller Nema17 motor but I noticed…
Maytag Oven Knob labeled "KIP 5D94" on the back. Files include the original scan and a CAD model in STL. These are visually indistinguishable from each other when printed. These were created for someone else, so I haven't had the chance…
This is the ROCKET CANDY model, a rocket designed for experimenting with and learning about aerospace propulsion. This model is specifically sized to be powered by: A D9-5 type black powder motor. Or DIY solid propellant (Rocket Candy…
Tools to assist in the setup and maintenance of a MOD9.
Using the SCAD file from the original , I expanded the AAA and AA columns. Can hold the following battery types and quantities: AAA: 56 AA: 40 C: 6 D: 5 9V: 6 Print Settings Printer Brand: Creality Printer: Ender 5 Plus Rafts: No…
I was trrying to found some models that would fit my car well but i didnt find any so i made my self one i am using 12V 10mm wide led stripe and some m3 screws for mounting I printed it in PLA but i would say you can print it with any…
When travelling, it was hard to find a place to put this camera, with a view from above the bed. So here is a camera mount to be fixed on the bed. You need a piece of wood, and some M4 screws and nuts. Once assembled, you can mount the…
I built the remix of Void's 3x3 macropad - the Void9 - which is here (https://www.thingiverse.com/thing:4816077) on thingiverse. The dimensions for the remix and Void's original are, so far as I can tell, the same so this model should…
Seems as though many people are interested in Electronic Lead Screw's for hobby lathes. You need to mount and encoder to keep track of the spindle position so that you no longer need to mechanically force the spindle and Z axis position…
Uploaded at the request of an inquisitive redditor, this 9 sided polyhedron is created with the intended use as a basis for a 9 sided die. This die has not yet been tested for fairness, and there is no mathematical proof of fairness, so I…
Dies ist eine Abdeckung für die Handbetätigung vom Schiebedach am ED9, Habe diese mit Carbon- PETG gedruckt mit 25% Füllung und 3 Lagen Wandstärke. Passt super und lässt sich problemsos auch wieder abnehmen. This is a cover for the manual…
Unfortunately bleugh's fantastic belt tensioner (thanks for that btw) doesn't fit the D9 MK2 400mm version: the Y-axis wheels collide with it when moving the bed to something like >370mm (which happens at every z-calibration). So I just…
Made for exchange demages old part. Inner diameter isn't fits, it have allowance. Supports are necessary.
This is a made from scratch redesign using measurements for where the nozzle and screws are at from the 'Cii inspired cooler for Duplicator 9' part cooler by panylund (thing:3127625). It is a re-inspired model :). I originally made a…
Ender 3 base with the Philip Avent SCD923/26 lock mechanism connected with a printed bolt. Bolt should be printed with 100% infill,
Y Reduzierverteiler 1x 98 auf 2x76mm AD 1x in 2mm Wandstärke/1x in 3mm Wandstärke Y Reducing manifold 1x 98 to 2x76mm OD 1x in 2mm wall thickness/1x in 3mm wall thickness
Potřeboval jsem někam umístit jeden 5.65" displej, tak jsem pro něj vytvořil jednoduchý rámeček podobný tomu, co mám pro 4.2" modely. Seznam součástek: Good Display GDEP0565D90 5.65" 600x448 LaskaKit ESPink ESP32 e-Paper LaskaKit SHT40…
Engine bay for MN D90 with space for two 18650 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: PolyMaker PETG Category: Toys & Games
I wanted to print out Hadamard90's tulip but I wanted a flat base to make it more stable. I also designed a stem so I could place it in a vase with other flower and not have to worry about leaves breaking off. Filament for stem is Just…
LATEST version 3 - Uploaded here: https://www.thingiverse.com/thing:4212688 Custom Cooling duct for Wanhao Duplicator D9. Working well compared to stock.. working on next version for blower fan which shall improve this more.. Please post…
The battery door latch for the D50 D70 D70S D80 D90 D100 cameras can break causing the door to not properly latch shut. This is a 3D printable replacement part for the latch. Print Settings and Recommendations: 0.2mm Layer Height 100%…
Wanhao Dupliator9 MKII Bauteillüfter. Remix, von Grund auf neu gezeichnet in Fusion 360 Der Flansch ist für einen 50mmx50mmx15mm Radiallüfter Print Settings Printer Brand: Wanhao Printer: Duplicator9 Rafts: No Supports: Yes Infill: 32%…
Tested with this DC to DC converter: https://de.aliexpress.com/item/32833258033.html
These are long dice, they have a shape of a prism capped with pyramids. When rolled, these dice end up with an edge on top, your roll result is the sum of the pips on the faces sharing that edge. Dice like these are called “cycle dice”…
Replacement gearset for the Office DEPOT HD95 laminator. You'll need to print 2 of the roller gears to have a complete set. Remember that it's HOT where these things live, so use an appropriate material; I used PA-6 Nylon. (6 Walls, 30%…
Print with strong material. No PLA. PET and Nylon worked best. Design is made for Lizard95 with VTX02 VTX03 and a Runcam Micro (19mm or similar micro cam) Category: R/C Vehicles
added braces to allow the spool holder to be mounted to the 4040 profile on the wanhao Duplicator 9 added 5mm holes to make sure the pieces are held together as they are floating more than originally intended and added 5mm holes to the…
Headboard mount holder for a ThundeaL TD93Pro projector or other appropriate. initially, the mount is straight, if you need an angle, an additional angle expander is attached, you can also download the project and convert it to Fusion360
this shroud is based on the rogue SD shroud. so it uses the same barrels. but I found that with short shrouds like this it's quite east to place your hand in the wrong place. so in case you like the look of a P90 ish style grip more then…
All D and F series parts are compatible
Topping D90 / A90 Feet I wanted to increase the space between my Topping D90SE / A90D dac/amp stack as this gets very warm to the touch and the existing rubber feet are only 5mm tall. I also wanted space to run my headphone cable…
Update 7/2/2025: The device firmware is complete with a v1.0 release, creating the user experience of ever-appearing CW stations as you turn the tuning knob. https://github.com/jhogsett/FluxTune/releases/tag/v1.0.0 Update 6/27/2025: There…
A couple of cases for the RFD900-UX so that you don't have stuff dangling around. Bonus cover included that I wasted time on trying to figure out how I could Light Pipe out the LED's... but one is behind the metal, so it's a big hassle. I…
Dies ist eine Zugentlastung für den Wanhao Duplicator 9. Diese kann nur montiert werden, wenn der Extruder so angebaut ist, wie man in den Bildern sehen kann! Man braucht zur Montage folgende Sachen: 2x Schraube M3x12 + Unterlegscheibe 2x…
It's no secret that the hot-end on V1 and V2 Wanaho D9s are hot garbage, with quite possibly one of the longest moment-arms I've ever seen in a system like this. After converting my Monoprice Maker Pro (D9 v1 clone) to a linear rail on…
A 45-degree mount for a generic clone/rebranded SMKD92 Koolertron Macro Keyboard. I have included Illustrator files of the board dimensions and the Tinkercad links for easy modification. Unfortunately, the screw holes are slightly off so…
This piece is a replacement that I designed for a part of the battery that broke. It is the piece that is placed under the cymbals. You have to make two to connect it to the other. Printer: Ender 3 V2 Filament: Sunlu PLA Time: 40 minutes…
Bought GUCEE HD92 960p from Aliexpress as it was a reliable and cheap webcam. I left the existing metal feet on the camera. This model is meant to slide on this existing feet and is split in several pieces to make printing easy. The fit…
This is a protective cover for the NASTY D9Ki 9000 Puff Vape. Has all the necessary holes for airflow, charging and display. Has a lot of available area for customization like names or logos. Preferably you should print in PETG or…
Avent SCD923/26 - camera holder philips
Two colour MI Band 9 stand. PLA printed, some supports needed.
https://www.3djake.it/bigtreetech/dc-dc-stepdown-module
You ner screw 5mm x 65mm
I wanted to combine various parts I had into a useful device for creating sound effects. This uses two Arduino Nanos, three AD9883 signal generators, three rotary encodes, a 20x4 LCD display, and various other components to produce sounds…
Lizard95 flexible Akkuunterlage mit Rillen, damit der Akku nicht rutscht Lizard95 flexible battery pad with grooves, so that the battery does not slip Category: R/C Vehicles
i don't want to change it every time i crash so i design a beef up one Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 100 Category: R/C Vehicles
After switching to a bondtech extruder on my Duplicator D9 (400 MK2) I noticed an increase in heat-creep induced artifacts on my low-temp material prints. I was expecting this somehow since a few factors are handicapping proper…
https://it.aliexpress.com/item/1005004569914022.html?spm=a2g0o.order_list.order_list_main.137.21ef3696lhiffB&gatewayAdapt=glo2ita…
This is a simple lens hood I designed for the Sony Mavica MVC-FD91, they really have a way with names don't they? Sarcasm aside, I really enjoy shooting with this camera, but don't like how the lens can get very overwhelmed when shooting…
The Zastone D9000 radio comes with a handheld microphone connected to the radio with an RJ45 cable. This is a desktop microphone that uses the PCB from the original microphone. There are two buttons, left and right, but only one of them…
Cheapo Well D90 full auto airsoft, fires when BB's get to the hopper. as standard this requires a lof of shaking in the air, dry fires are common. Reducing size of Mag and keeping BB's at rear improves feeding, makes gun more reliable,…
Small stand for a Cessna MD90 Clock. I painted mine glossy black, a barrel jack is used in the back for power, and wires are run through the base and legs.
