61 modeli
UPDATE 16/01/2022 Added BOM for electronix case. I'm not going to be doing a manual as it's self explainatory with the photos. Acrylic panels an associated mounts also included. Stl files uploaded for these aswell. Optional handle can be…
You need mosty M3 bolts like any voron does, a few M3 nuts and a few extrusion nuts and M3 heatinserts. For the CoreXY part you need MGN12 rail (I used 350mm on Y and 300mm on X), A about 1m long GT2 belt and 24 F623RS bearings. THIS DOES…
I recommend printing it with 3+ walls and 10%+ infill.
I purchased a Creality Sonic Pad for my Ender 5 Pro, but the brackets for the Res.Sensor that Creality has on their web site all require supports... I tried printing one of them, and I tossed it after I 5min of filing down leftover…
I've seen other pen holders and I didn't like the spring mechanisms that presses the pen down to the drawing area. (rubber bands, spring in the pen, …) My holder uses meander springs that are printed with the part. This spring can be…
I needed to raise the limit switch to work with linear rails. Print 2 walls or more 20-25% infill. Uses the stock limit switch for an Ender5.
use the Git-hub for the rest of information
I like to print direct from the filament dryer. In order to connect a bowden on the entrance I designed a new sensor bracket with a additional bowden connector. The bracket can printed as shown in the picture without support. The…
UPDATE 07/01/2022 Refer to the Electronix Case for acrylic panels, associated mounts and BOM. https://www.thingiverse.com/thing:5110697 UPDATE 07/01/2022 The small printable panels to fit each end of the rear frame replace the acrylic. I…
Z-axis lead screw stabilizer. You'll need 2x 608 standard bearings and some 4/M5x10 bolts with 'T' nuts. This takes out the wobble at the top of the lead screw, however this is just part of the upgrade as you'll need flexible couplers…
A small design to add side- and a back wall to an Ender5+. It's a super easy and fast upgrade that lets your Ender5+ to look a bit tidied up. No more loss cables that you can directly see. The only thing you have to reposition is the…
this for the Ender5 plus core XY conversion for ZeroG or any core XY
DEPRECATED DESIGN Please be aware I am not developing this design any further. Cable cover/enclosure for the Ender 5+ cables coming out of the control box. Category: 3D Printing
These bed supports make the bed much more rigid (to a surprising degree) than the completely printed bed supports I was using previously! I've also included a .STEP file of everything to make editing it easier. 3/4in Angle Aluminum Ender5…
This print is made for using with an all metal hotend. The stock end will be too tall, but might work if you removed or swapped out the hose retainer thing for a shorter one. My hotend is a gulfcoast robotics type, like this:…
Bracket for mounting pad7's ADXL accelerometer SPI-Device to Creality Ender 5 S1. needs m3 screws for mounting. i used my inserts in this pictures as i ran out of heat inserts and/or m3 screws. works neatly, can be found here:…
This shroud reduces the noisy turbulence created by the metal cover of the extruder cooling fan in the Ender3/5 (and other) machines. Please note that this does not make the fan silent - instead it lessens the harsh frequencies created by…
Remixed Ender 5 (Pro, Plus) hotend strain relief for bowden tube and heater/thermistor wiring.
The end stop holder was broken so I designed a replica. Printed with 0.28mm resolution for higher strength. I used the screws that held the switch in place to tap the 3D printed part. Worked well. Print Settings Rafts: No Supports: No…
DEPRECATED DESIGN Please be aware I am not developing this design any further. Sick of not being able to see the nozzle on your E5+? these two brackets I modelled (to fit in with my tensioners) drop the front extrusion bar down 40mm so…
I made this simple arm based off an old CCTV camera wall mount I had laying around. It's designed to be screwed on the top of a 2020 extrusion with an M4 screw and a hammer nut. For my application I used the rest of the original hardware…
Using 2020 aluminium extrusions here's a simple but strong little table to sit your Ender 5 Plus on. It's not the cheapest thing to build but it's stable and adjustable. I used my Lack table top as I was not comfortable sliding that table…
I changed the model to fit a Dragonburner upgrade on my ender5 plus carriage mount. V3 added strength and 2 additional bolts , just need to drill stock carriage plate to accept 2 exsta bolts. Its printed with 0.2mm height, 4 mm width and…
11/06/2022 Upon a request I have added 12mm & 18mm EzABL mounts. These are untested and may need a little sanding for clearance. I have allowed clearance for mounting hole and the nuts but not the lock washers. DEPRECATED DESIGN Please be…
Redesigned the backing plate, cable arm and EZABL Pro mount to fit my Ender 5 Pro with the Micro Swiss Direct Drive kit and all metal hot end. Will also work for Ender 5 of course. The EZABL Pro screw mount is somewhat thin given you have…
This is a small adapter plate for mounting the Microswiss NG direct drive extruder (I have the Revo pattern but they should all be the same) to the 3DFused CoreXY Ender 5 motion carriage platform. The countersunk holes are designed for…
I had this bug with the display beeping regularily at my ender5. I found out this doesn't happen when the display it is not connected to the frame with the metal-stock bracket. So I designed my own bracket to be printed. My first…
I wanted to reposition the screen to have it vertical, saving a bit of room. This will take M3 screws and bolts to attach the screen to the block. Here is the raw onshape link if you want to mess with the model :…
I had this bug with the display beeping regularily at my ender5. I found out this doesn't happen when the display it is not connected to the frame with the metal-stock bracket. So I designed my own bracket to be printed. My first…
On the Ender5 the display is mounted on the side and takes quite some space. To reduce the width of the Ender5 I decided to mount the display partly inside the Ender5 cube. The display can only get so far into the cube that it does not…
The tool holder is 20mm wide, thus it fits on the printers profile. In my print on Allen key hole is missing, but its part of the model. The holder is mounted with 2 M3 screws and T-Nuts in the first and last compartment of the tool holder.
I brought in the original STL (from Bingbingaling ) as a mesh and modeled the extension around that. Attaching the original model here for convenience. https://www.thingiverse.com/thing:658851 Light Switch Extender for Young Kids…
I've recently upgraded my Ender 5 Plus to a Mercury One.1 and while I don't have a proper electronics enclosure yet, I wanted to have all my electronics mounted in the original case for now. In order to have my Raspberry Pi and the…
si fissa alla parte centrale posteriore tramite due viti, essendo inclinato permette di istallare una bobina senza che questa ingombri.
This remix is for addressing the wobble and high center of gravity issues from the original design. Now this version clamps firmly to the plate and sit lower than the original design. This design needs 4 M3x5mm heat inserts.
Remixed the bottom plate to have SD-card acces. After a few failed octoprint upgrades I was tired to remove the bottom plate everytime. Check also my other designs: https://www.prusaprinters.org/social/201278-hans/prints
Trays for the waste of space in the rear of the Ender5 PRO, there is a breathing cut-out for the vents at the rear of the control unit. Base is a little thicker to protect it from anything thrown in. Included without end wall if you want…
This is a small adjustment for the y-axis, to let the y-Endstop trigger a little bit earlier. If you like to, check out my other designs too!
extracted only the bed from the whuge detailed stl of the whole Ender5 as I don't need whole printer model inside a slicer with all the screws and belts and... bed is enough .. simplified the bed mode to cut down the number of polygons,…
I've recently upgraded my Ender 5 Plus to a Mercury One.1 and while I don't have a proper electronics enclosure yet, I wanted to have all my electronics mounted in the original case for now. In order to have my Raspberry Pi and the…
Printer: Ender 5 plus Rafts: No Supports: No Resolution: 1 Infill: 15% Filament brand: Creality Filament color: Weiss Filament material: Pla
Additional electronics box for a Creality Ender 5 with room for a Raspberry Pi 3 and 4 mosfets. Based on measurements I made from my own Ender 5. I'm not sure what the variations are between different printers of this model, but it is a…
A typical problem on the Creality Ender5 is that the wire harnest gets caught on the X-Motor on certain moves. This cover helps the harnest to get over the motor smoothly. For mounting you will need a M4x15 screw and a M4 t-slot nut.…
Model have two parts connectd with m4 screw and rectengular nut, which also keep the whole construction in place on the case. And on't tighten cable too much. Leve it free to move.
Simple holder for Dual Flex3Drive for Ender 5. I was told Ender 3 uses same carriage so this might work for Ender 3 too but I have not tested, if you do test please comment. Printed in PETG but any material should work (stiffer the…
Support adapter à mon besoin , réutilisation de la pièces cylindrique supportant la bobine Matériel: pla ou petg Hauteur des couche 0.2 nombres de parois 3 Remplissage 15% à 20% Bonne impression
la maschera di foratura va posizionata sul carrello inserendola nei fori e facendo passare i perni nelle sedi, una volta fissata si praticano 3 fori M3 praticate prima una ammaccatura con un bullino nelle posizioni di foratura per essere…
si fissa con due viti e si completa con un cuscinetto 608zz. Visto che si stampa con la parte che porta il cuscinetto sul bed il collo del supporto diventa debole per cui inserendo una vite M3 da 15mm nel foro piccolo sotto la base si ha…
Upgrade your ender 5 Plus to direct drive with just one part. Version A (M3 Knurled Brass Nut): 2 M3 X 30 Socket Head Cap（1）； 3 M3 Knurled Brass Nut（M3X4X4.5 - 6mm）（2）; 4 The Orbiter V2.0 Extruder; 5 Teflon tube（mm）
I'm modifying my Ender5 plus with the MercuryOne mod and I've decided to replace the original Creality switch feet with a backlit circular one. ~Printed on a Centaury Carbon with SUNLU PLA+.
This model is a remixed "lid-less" version for Ender 5 frame-mounted power switch cover by Gr8rSherman8r. This is to prevent accidentally bumping into the (otherwise great) front-mounted power switch, as well as to ward off children to an…
si posiziona all'uscita dei cavi creando abbastanza spazio per fissarli tramite fascette crendo un poco di ordine
This is a flexible wire harness support for the Ender5S1 made by Creality. I was not a fan of the way the wire harness was getting crushed during the homing process, or how it would drag on the build plate for certain prints. I designed…
I have what used to be an Ender5, and as I've made various modifications to it, I decided I didn't like have all of the wires bundled up in a sleeve. They are easier to access when they are more loosely bundled up. Problem was that there…
con opportune viti si fissano tra il telaio e i piedi di gomma originali alzando di qualche cm la stampante permettendo una migliore aereazione della scheda madre e del motore z posteriore che quasi tocca terra
I changed the model to fit a Dragonburner upgrade on my ender5 plus carriage mount. V3 added strength and 2 additional bolts , just need to drill stock carriage plate to accept 2 exsta bolts. Its printed with 0.2mm height, 4 mm width and…
I'm modifying my Ender5 plus with the MercuryOne mod and I've decided to replace the original Creality switch feet with a backlit circular one. ~Printed on a Centaury Carbon with SUNLU PLA+.
Support adapter à mon besoin , réutilisation de la pièces cylindrique supportant la bobine Matériel: pla ou petg Hauteur des couche 0.2 nombres de parois 3 Remplissage 15% à 20% Bonne impression
This remix is for addressing the wobble and high center of gravity issues from the original design. Now this version clamps firmly to the plate and sit lower than the original design. This design needs 4 M3x5mm heat inserts.
