Arm replacement for Steelcase please
You need for each arm 5 M4x14mm nuts. It is recommended to use supports on plate only.
- Pobrania
- 222
- Polubienia
- 16
- Ocena
- 5
35 modeli
You need for each arm 5 M4x14mm nuts. It is recommended to use supports on plate only.
This is a Coat Hook for Steelcase 3" cubicle walls. It is my first design that I am publishing. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Resolution: Fine Infill: 50% Notes: Flip the part…
This is a chock for the casters/wheels of a Steelcase Leap office chair. V1 was a chock that allowed the wheel's weight to rest on the floor. Without the weight on the chock itself, the friction between the chock and the floor wasn't…
This headphones hanger mounts up to steelcase slatwall.
The name and summary cover most of everything. If you have an Amia you have most likely been frustrated by being limited to being locked upright or going into full recline. This model gives you 4 options for recline in 8 degree…
Snap-on replacement for the back tension knob on Steelcase Leap V1 and V2 chairs. Optimized for 3d printing with a flat face. Knurled edge for grip. Print either just the body or the blank file in a single material, or combine the body…
The pen/pencil caddy that came with my Slatrail desk is so small, was a joke. So I made a simple, bigger one. It is boxy, but holds a lot of pens. I used PETG to print mine with supports for the the clamp section. Any resolution should be…
Replacement roller set for the Steelcase Tanker desk drawer. I printed in PETG with 40% infill and 4 perimeters for strength.
Printed in ASA without supports. Overhangs might not work with some filaments or without appropriate cooling. Updated to large version which fits Expo erasers!
UPDATE: WARNING: this part will probably break after a couple weeks if printed in plastic - learned that the hard way. Use this for temporary fixes, or if you can, print this in a strong material (metal if possible!) to ensure it lasts a…
This is a small keyring holder that will fit into the Steelcase brand Cubicle slatwall. It is modeled loosely off their discontinued part, with several minor changes to make it a stronger print. You will need to print this with support.…
I have a Steelcase Amia office chair. It's comfortable and I like it quite a bit, with the exception that occasionally it develops a squeak when I lean back. The solution is to lubricate the tilt mechanism, which is under the seat pan.…
The Steelcase Amia/Leap v2/Think armrests have a tendency for the plastic cover that prevents the 4-way adjustable arms from pinching you to become loose and stop fitting. This happens because the plastic clip pieces will break off from…
This is a mount for having a headrest on Steelcase office chairs, this chair is a classic in econometrics but most don't have headrests. This sturdy mount can be screwed (with wood screws-M5x20) directly in the plastic back. The mount has…
Adapts a phone with a standard 2 or 3 screw wall hanging mount to the modular Slatwall system found in some Steelcase cubicles. Instructions Print with moderate infill and extra perimeters. Screw in 2 or 3 self-tapping PC case fan screws…
Replaces a 75mm wheel on a stemless caster, for an older Steelcase Leap office chair. No idea how this will hold up over time, or which models it's compatible with, sorry! I increased several dimensions to reduce weak points, including…
The Variable back stop / Tilt limiter Knob on my Steelcase Please Chair broke, so I made a new one. Works just fine. I printed it with supports, with the wide part facing up.
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/gflj9vYuB2T Print Settings Printer: Monoprice Maker Select V2.1 Rafts: Doesn't Matter Supports: No Resolution: .2mm Infill: 20% Notes: Slightly improved…
SteelCase Cubicle Slat Wall Utensil Holder
pen clip for the pull out desk extension on my vintage steelcase desk. Printing Instructions print in downloaded orientation, Arachne perimeter generation is strongly recommended.
I was struggling to remove my Steelcase Think seat for cleaning, so I designed this tool to easily remove it without damaging anything. Here is how to use it : Pull the seat part to fully extend it Place the tool between the black plastic…
This is a set of hooks designed to go between two adjacent panels in a steel case cubicle. I needed a way to store long material stock (carbon fiber tubes and some metal rod) that was clean and looked nice. This was the solution. This…
This hook is designed to attack to the endcap of a steelcase standing desk without any screws/glue/etc. Just pop it into place and you are all set. Printed in PLA with 4 wall loops, and 50% infill. Strong enough to handle the heaviest of…
I don't like having armrests on my desk chair so I always remove them. The Steelcase Leap V2 has holes on the sides where the armrests go. These plugs are for capping those off. I printed in TPU 95A. Included the OpenSCAD file.
I needed new armpad for steelcase “reply” chair and could not find any. The “please” model i “remixed" looked correct, and while it has the same screw pattern, the reply chair has a larger armpad so did not fit. I rebuilt this model from…
You can put the leg extension at the end of the table legs to give tall people a good table height.
A replacement foot for steelcase chairs. Printed in PLA and TPU for grip. Category: Office
you need two pins for each arm rest so four pins total for one chair. I printed in PETG at .20mm, 20% infill seemed to be fine. Higher temperature would probably be better because the pins are somewhat in shear. To remove the cover there…
I slightly remixed this https://grabcad.com/library/atlas-adaptor-bracket-for-steelcase-gesture-1 top adapter to make it compatible with M2.5 heat inserts. I uploaded the .STEP file so that anyone can change the diameter of the hole to…
Our new office has 4' tall Steelcase whiteboard cubicle dividers this is a hook for hanging a backpack. Use the original Bolt that holds the tray on. The washer is for the other end to make the tray level. I used two hooks, so I have not…
WORK IN PROGRESS - Steelcase Please v2 Backrest Fix Bracket
Wheel box for steelcase gesture office chair. Print five of these to mount your chair to something else. I'm using them for a sit/stand solution for my treadmill desk. I used zip-ties and a slot in the side of the boxes to keep the chair…
My original knob broke internally. It would click and skip when turned, and the tension stopped changing. The tension mechanism itself was fine; the knob just couldn’t turn the shaft anymore. Original replacement knobs are hard to find,…
This is a replacement for the seat height adjustment lever which actuates the gas cylinder on side and top actuating Steelcase Leap chairs. Simply drop into the bracket and rotate upward until it snaps into place. Check the photos for the…
Use this adapter to mount Leap V2 Armrest pads onto an earlier Leap V1 model with a metal armrest base (see last photo of bare armrest). Message me if you are concerned about compatibility. You will need to print 2 of “Leap V1 Armrest…