151 modeli
This is a 3D-printed replacement cart lock for the Weber Traveler barbecue. It is a direct copy of the original part. The part should fit all models of the Weber Traveler. Context A friend of mine also has a Weber Traveler as his cart…
I have a weber "Master Touch" Grill and a iGrill2 thermometer. The problem is where to place the thermometer during grilling. It has a magnetic base, but you cannot stuck it to the kettle, it is too hot. So I designed and printed a small…
I broke a clip for my Weber Q1200 Portable cart. Needed a replacement. This clip works perfectly, providing a snug fit and Latches great. GCode is for Prusament PETG Print instructions Perimeters: 6 Solid Layers Top: 6 Solid Layers…
It is designed so that no support material is needed when printing, therefore it is an angle below the radius for easy print. Diameter: 40 and 45 mm Height: 55 mm Printet with PETG.
Remix to include Weber Workshop resin vials
Printed in PETG with max amount of walls 0.4 nozzle and 0.2 layer
Foot for Weber Grill, better on the snow than the original.
Base / stand designed to hold Weber Workshop Commercial Bean Cellars. Four options; • Single base to hold 2 x 6 Bean Cellars (with or without base) • Double rack to hold 3 x 10 Bean Cellars (with or without base) Print with ironing…
The knobs of my Weber gas grill didn't look that good anymore, so I decided to print new ones. Just took an original one to catch all the dimensions. I gave them a little touch by adding a Batman Logo into these knobs. I don't own a MMU…
This wheel replaces the wheel from a 22inch Weber Kettle Grill. It probably will fit a lot of other grills as well. The wheel diameter is 6inches (150mm) and it will fit a 10mm shaft. I purchased a 22inch Weber Kettle Grill from an Amazon…
Tool hooks for your Weber Works grill. I printed this with PETG, supports, 3 perimeters and normal infill. But not sure if any of these are mandatory. Some flexing helps this attach it to grill, and your grill is outside, so maybe not…
Imprimé en PLA changement de filament entre le noir et le blanc, le rouge a été imprimé à part. Imprimé en couche de 0.2mm Changement de filament avant la 11ème couche. Epaisseur dessous dessus : 8 couches pour remplir entièrement la…
I was driven to create this as the official caddy in Australia is pretty expensive. This upload also includes hex hooks for hanging accessories off the tool caddy itself! Print the tool box in the orientation shown, i printed it in PCCF…
Replacement for Weber Grill foot. It has a different angle than the model from @echo https://www.printables.com/de/model/412574-weber-grill-foot I needed to use a different angle than the original foot to fit perfectly on the grill. The…
Link to https://cults3d.com/en/3d-model/various/weber-45-dcoe
I needed a replacement for my Weber Spirit grill knob. So I made one in the style of the knobs on a Marshall amplifier. I printed mine in Galaxy Black ASA and then switched to PLA (Viva la Bronze) for the top part. I added a GCode file…
Weber Slate Paper Towel Holder A convenient 3D-printed paper towel holder designed to attach to your 28" Weber Slate griddle's side table. This two-piece design features a secure clamp mechanism that grips the table edge and an integrated…
If you like my work and enjoy my models please consider leaving me a tip/donation, It helps me to continue creating awesome models for you for free. https://paypal.me/muddymaker BBQ Drip Tray Aluminium Foil Stamp to fit Weber style BBQ's.…
This is something I needed rebuilding the engine and servicing of a 50 year old classic car and no matter how hard I tried to look no one offered something that mounted to this Weber carb (for free, several people sell these very looking…
Be sure to use filament with some flexibility and UV resistance. Also print it sideways (as in the .3mf file), so the hook doesn't break when you clip it onto the griller's sidebar.
Weber Slate Trash Bag Holder A practical 3D-printed trash bag holder designed specifically for Weber Slate griddle. This three-piece design features two main body sections that connect via a precision dovetail joint for a secure,…
A filter (around 2mm grid size) that inserts into a 2" velocity stack, as used on e.g. Weber carburetors Category: Automotive
PETG and so many walls that the thing is solid ..and just send it.
I wanted to reuse the chrome plate from the original knob but couldn't find an existing file, so I decided to make my own. It's not perfect but the plate fits, I added a tiny piece of clear 3M mounting tape for a more secure fit. Printed…
Be sure to use filament with some flexibility and UV resistance. Also print it sideways (as in the .3mf file), so the hook doesn't break when you clip it onto the griller's sidebar.
Holder is made from two parts and additional parts are not needed Mounting part fits directly to Weber Spirit Grill (probaby to others as well). It has Fish tail mechanism to lock the two pieces together, but there is also possibility to…
Drip tray for Weber Q BBQ's. These plastic trays replace the disposable aluminium trays that sit in the slide in aluminium tray under a Weber Q series BBQ. The trouble with the disposable aluminium trays, (or just using aluminium foil) is…
Got a new weber slate, it came with big clunky clips, my tongs and stuff had smaller holes so I made these to be able to hang them on the side.
This is designed to hold a wheel on a weber grill. it works by tension no glue needed. recommended PETG but PLA+ likely works. I tapped mine on with a rubber mallet but a hammer should also work. it could cap other wheels onto axles if…
Perfectly matches the shape of the grate at 45 degrees.
I am trying out the Weber Blind Shaker / Tumbler (can be seen with both names), but I didn't want to sacrifice the option of using the original Niche cup with my grinder. I modeled the original cup holder and added cutouts for the Weber…
Funnel designed to fit the opening of Weber Workshop's Polymer (aka Resin) Bean Vaults. Fits some other designs as well; outside diameter is 28mm at the bottom, and 60mm at the top. New design (Sketchup File included) inspired by this one…
This is a roll for the 3rd foot of a kettle charcoal grill from Weber.
For whatever reason the Weber Genesis Storage Box on the side comes with mounting holes for 2 trays but only comes with 1 tray…. Maybe they had the intention of selling an extra one? but they don't sell it… Why waste the space, here is a…
This is an accessory to hold the temperature probe of a webber grille.
J’ai crée ce modèle suite a la casse du bouton d’origine. mont but était de garder le maximum de pièce pour être le plus fidèle a l'original. - il faudra démonter sur la pièce d'origine l’insert rouge et le cerclage chromé si vous en avez…
Foot to replace the frontfoot of a weber bbq. it has a very tight fit, so you don´t need any glue. Just push hard enough! ;) Printed in PETG 0.15mm, 0.4 nozzel, 3 perimeter, 40% cubic infill.
I found this print in thingiverse, and it has been incredibly useful so I decided to share it here to increase its visibility with our community. It consumes little filament, is easy to print and while it exposes the airtag and it will be…
The Weber Connect base is magnetic and easily attaches to the grill but the temperature probes are not. This hanger/holder attaches to the back of one or more probes and fits on the hooks on the side of the Weber Genesis grills. I believe…
Print in PETG 6walls 25% infill. Bolts to use M6 35-40mm M6 14-16mm and M6 nuts. One M4 18mm and one M4 nut.
Remix of Basstronics' knob. I believe this one is better as it indicates the position of the knob in a clearer way :-) Please read Basstronics' description as to what model it's for and so on, I don't own a Weber grill myself. I've…
Shows good fit on the carburettor but should be regarded as a prototype.
Works with most Weber Spirit Ignitions. You can print it in Multimaterial. Print in 0,2mm in PETG or higher
Weber Workshop resin bean cellars are fantastic ways to prepare the proper amount of coffee. This caddy allows for 5 resin bean cellars to be stored vertically. There's also an inside lip which matches the outside diameter of the caps,…
Short funnel to help fill coffee bean tubes faster
Beim Weber Gasgrill SPIRIT E-325 GBS (Modell 2025) fehlten mir die kleinen Lenkrollen. Im Original sind einseitig nur Standfüsse verbaut, ich bevorzuge jedoch Lenkrollen weshalb ich einen entsprechenden Adapter konstruiert habe.…
Replacement end cap for front leg on Weber grill. Extends the leg length 20mm (13/16") so the grill surface is level. Fits 1" (25.4mm) diameter legs. Printed with PETG for outdoor use. Printed with a brim and no supports. 40% infill. 0.2…
This is a dock for a Weber Connect thermometer, which doesn't only hold the dock, but also holds up to 4 temperature probes in a package with a compact footprint. The temperature probes rest on the probe and the holder doesn't touch the…
The photo shows the remixed larger wheel version next to the Blackstone (original). The model 1-16__1-4 gives you a step of 1/16" if used on the top, or 1/4" on the ground. The model 1-4__1-2 gives you a step of ¼" if used on the top, or…
It can print in PLA, but be careful if it gets hot outside. Print may warp. Not for all weber grills, make sure shape is right for urs.
This will replace the plastic ignitor button on a Weber grill. Instructions (1) Print the button_housing and button. (2) Cut a piece of 3mm filament to use as the hinge. (3) Drill out filament hole in button if required to get button to…
This part can used as replacement for Weber 43286 --> Latch for grill attachment
weber/dellorto carburetor jets holder simple design but very useful to keep everything organised check my other project too im not a professional designer but im learning have a fun ;-)
My neighbor's Weber Q Stand was damaged while moving in, so we took on the project to replicate one of the clips that was still intact. I designed the model in Fusion and attached the STEP files for remixes. I printed the parts in PLA,…
Many of the grill feet are for different revisions of Weber's charcoal grills with the wrong angle. This is for grills with a front leg that's at a 65 degree angle from the ground. Printed PETG with 3 wall loops and 40% infill.
Works pretty well! Includes upper, intermediate and lower gasket, scaled and based off the catalog drawing. To be printed in TPU. Eventually the gaskets swell, but since they are not subject to high heat, and they are compressed, they did…
Ho creato delle manopole di ricambio per la mia griglia weber. Stampate in ASA per resistere all'aperto.
This is a basic stand intended to hold a dozen bean cellar containers from Weber Workshops. It's specifically designed to work with their commercial plastic version, unsure if it works with the consumer glass version. Print Settings…
Keeps the cover on your Weber Performer securely in place - even in windy conditions. Category: Outdoor & Garden
Posting a make and giving the model a like is much appreciated!
Sometimes I find it hard to grip the collar around the propane tank. I wasn't able to find one for a standard Weber regulator. This is only 10mm thick which allow it to slide in between the regulator and the collar. It is just long enough…
I melted the original (don't ask), this is just a straight up caliper-measured copy (almost exact) of the original two-piece handle that is used on the lid and the side of many of the basic Weber BBQ grills. So if you melted yours off…
The hooks on the side of the grill were too small to fit grilling tools with thick handles, so I made a new one.
Intake manifold for mounting the Weber 40 IDF carb (and similar) to a Fiat 850 engine in a Fiat 600-based car (no tilt). This intake has a bottom end similar to the JO/EL intake (see pics), which means it will need quite a bit of intake…
The well known Weber kettle BBQ unit comes with two usable wheels on to the rear legs, and a front leg which needs to be lifted before the rear wheels can be used. Lift it a tad too far, and the whole unit topples. Err on the safe side,…
Be sure to use filament with some flexibility and UV resistance. Also try to print it sideways, so the hook doesn't break when you clip it onto the griller's sidebar. You might want to print it with 100% infill too.
I have had on two occasions where rodents got inside my Weber Q BBQ to make nests. This plug stops them gaining access via the bottom hole by plugging it. If you use carefully you can ensure that nothing can get up into the Weber Q…
I designed this replacement foot to go on my Weber Spirit II gas grill, the original rusted off. The inside is slightly raised so that the leg will rest evenly, and the outer wall is taller so it can be sealed to reduce the rust from…
This a highly esoteric thing - but very useful when needed. When setting up a Weber DGV 32/36 carburettor the first thing that must be done is to set the fuel chamber float to the correct level. Normally this is done by squinting across…
One of my knobs was flaking its top layer off so I designed replacements. Each knob is 2 parts held together with compression. No support material needed during print. I suspect they will work for other Weber models. Printed on both a…
I was having problems reading the display of the iGrill thermometer in direct sunlight. To make the device a bit more useable i added a shade. I designed this with the sizes of the original base, so it fits perfectly on the metal tray…
I got a Weber 6750 Instant Read Thermometer, but found out it doesn't have any loop to hang it by. So this is a small adapter that can be hung on a hook and then hold the thermometer. Best printed on its side, using organic support for…
Magnetized base for the Weber iGrill Mini thermometer and cable. The original comes with a black piece of plastic to roll the cable around, but it's not magnetized. I used to leave the iGrill Mini stuck to the fridge door, but the cable…
Made this to fit my friend's weber genesis. 9mm key hole.
I live on top a windy hill and even with the BBQ strapped to the wall it moves around. These wheel chocks keep it place. Onshape Link
BMW E30 316 Pierburg 1B to weber 32-36 intake adapter. The design is still work in progress, I hope, that I help somebody with designing this. The amazon link to the Carbourator, I used:…
This is a upgraded model of the original witch is more durable
I wanted to prevent debris and animals from getting into the side burner. 0.6mm nozzle, 0.3mm layer, PETG, Sovol SV01
Weber has a line of ‘add-ons’ to their grills. I just bought a new bbq grill from them and wanted to make my own rather than spending tons (more money I guess) on their products. I measured the rail of the Weber spirit grill side table…
After an oopsie, the igrill cover melted so instead of printing a cover I wanted to add a bottle opener. The original model was made for swedish coins so I remixed it to use a 5cts Euro coin. use 2x M3 screws to attach it to the grill
Negative piece is designed to go inside behind the sheet metal Positive piece can be added to a new or existing model of your choosing for a drink holder, shelf, or something else. No screws needed, pieces should fit together tightly.…
Ich habe hier die Drehregler von meinem Weber Q 3200 nachempfunden. Die Originalen haben leider wiederholt ihre Beschriftung verloren. Das passiert jetzt nicht mehr. Gedruckt auf einen A1 mit PETG und dem Strenght Profil bei 0.2mm…
I used PETG for the print. Nozzle diameter: 0,4 mm Layer height: 0,2 mm Supports: Everywhere Infill: 20% On the bottom side is a hole for a round 8mm x 1mm magnet. Here my print needed some rework to fit the magnet.
I’ve always been frustrated with how grill manufacturers often overlook utensil storage inside the cabinet. When utensils hang off the side tables, it becomes a hassle to put the grill cover back on. I much prefer a cleaner, more…
This is an adapter for a Weber 38/38 carburetor for a 3-inch tube, I found that there are somewhat expensive patent solutions on the web and I did not find any adapter that could be used with the most common size of K&N filters so I…
I loved the original design, but i always used one spot for my RDT spray bottle
For people like myself who are crazy enough to smoke or grill in full sun, this sunshade hood fits Weber iGrill Round Magnetic Bluetooth 4-channel thermometer so that you can actually read the numbers when standing in front of it, instead…
Nissan Terrano KA24E intake manifold adapter for weber 32/34 style carburettor - don't ask me why, here is the model Carb used - fiat 125p / fso polonez / zuk licensed weber 32/34 Print it with 100% infill, preferably with petg or some…
This is a brake block for the wheels of a Weber Spirit Grill. It is intended for the wheels with the nose coming out on one side. There are two versions of the block. Depending on how you have your grill placed, you might need a different…
Pretty simple thing really. I had a knob break on my grill, and I doubted that glue alone would work especially in the winter time when the valves are stiff to turn, so I designed and printed this sleeve. I put the broken part of the body…
I printed this out of 60D TPU and CF Nylon. Gave a set of each to a coworker. Not sure which they are using but they say the fit was great.
Print with MMU or similar. If using layer height of .2mm it's just the first two layers, where filament swap is required. I suggest printing with ASA to withstand not only temperatures but also UV from sunlight. Happy printing :)
Weber Grill Genesis lower-door pin/hinge. this pin sits between the door corner and the grill body and allows pivoting.
Used this as a template to file a 32 spacer to 38.
Be mindful of the hydrocarbon tightness of the print! I went with nylon. it was a temporary experiment, do not know how much it will last! you tell me.
Need a fitting funnel? Designed for interference fit for Basket diameter of 70mm.
You need a bushin that have 10mm outer Diameter.
I designed a copy of the bicycle-side part of the Weber coupling system. It is meant for various crazy DIY ideas. For instance, once I'm finished with it, I will upload a modified version of this design that can be used to lock the wheels…
Because of the missing hub cap I designed this. Wegen der fehlenden Nabenkappe hab ich dies erstellt. Category: Outdoor & Garden
A simple holder to keep your Weber grill basket vertical when storing. Maximizes cabinet surface area.
