Liczymy pasujące modele…
This is an adapter for BMW F series front door to attach aftermarket 100mm speakers. Originally I designed if for F22 2 series coupe + ALPINE STE-G100S but it may fit for other F series cars / speakers. There are many adapters in the…
With this adapter you can attach toolholders from the MODULA system. This is a universal adapter for (metric) PEG boards, this one fits Biltema, Jula, Clas Ohlson, and many others world-wide, CC 12mm (15/32 inch) spacing of the 4mm (5/32…
Updates: 26-Feb-2025 : V4 model Increased the size of the duct adapter significantly increased magnets holes from 4 to 9 added a 4in duct adapter requires about 7 in of clearance behind the printer (with duct attached) Requires about 200g…
This was printed on a Bambu X1C with PLA. No supports needed. Print with the Switch adapter side down. I did adjust the size of the bridge flow to make the bridging more aesthetic, but that shouldn't affect any functionality.
Designed this so that my wife's Hydro Flask would fit into the cup holder of my Ford F-150. Fits the 32oz wide mouth version. Opening for cup is 95 mm with based that fits into cupholder is 85 mm.
This is an adapter piece that allows you to connect any standard Apple watch bands to a pebble watch easily and comfortably. This should fit all pebble watches, although I've only tested with an original, 2 hr, and time. There will be…
You no longer need the Cirkul lid to use the flavour cartridges. All you need is the rubber gasket from the Yeti top and
Universal Vanilla Adapter This is a universal “vanilla” adapter for PEG boards/Wall mount, use this as a base for Your custom peg board or other surface you need to hang modules on. Fire up Your CAD app and insert screw holes, pegs or…
I have built RC Hex adapter for the tarmo5. (https://www.printables.com/de/model/348623-3d-printed-rc-car-tarmo5). The w
3-6-2023 - Made the walls a bit more thicker because of leaks. Infill should be at 100% i think. (not tested yet) Printed these models with 16mm in PLA+. The L and the T version uses support.
Fits the 4" Sawstop dust port to a 2.25" shop vac hose. The actual diameters are: Outer: 3 35/64" or 90.17mm Inner: 3 25/64" or 86.17mm Outer: 2 29/64" or 62.312 Inner: 2 19/64" or 58.312
In our last apartment, we had to saw our ikea ivar shelf in half to fit it in the storage space under the roof. Now in our new Apartment we have a storage space in the basement. So instead of buying new shelf legs by ikea. i just designed…
I included a couple photos of variants I rendered showing that the updated model can handle a wider variety of shapes. The rotation_angle can go up to roughly 120deg before it overlaps the drill hole, and works in both positive and…
This is a printable adapter that will limit the amount of cat food/treats that the Aqara Smart Pet Feeder dispenses. Modeled for a friend that wanted to use the Smart Pet feeder, but wasn't able to find anything else to limit the amount…
The JICCODA laser engraver enclosure https://www.amazon.com/dp/B0BM3W9VRH?psc=1&ref=ppx_yo2ov_dt_b_product_details ...doesn't have a standard duct for hooking up to 4" lines if you were (you should) using a 200CFM blower/piping. This…
There's a lot of frame braces for the Voron 0, but none of them use sections of Makerbeam XL. I had short 50mm sections begging for use, so I designed this adapter to do exactly that. When used in the front, the brace will run into the…
I designed these to let me replace wall switches with Phillips Hue remotes so that I can leave the switches on and use smart bulbs. There are two circles on the back for magnets, and a passthrough to allow soft resets via the switch. Hope…
My lyre was too small, so I made this adapter.
This adapter attaches to the Hisense AC unit. The dimensions of the connection on the back of the unit are roughly 162mm x 125mm. This adapts to a 6 inch diameter hose. The exhaust gets hot! I tried to print this in PLA(I knew it was a…
The original design is a great way to extend the height of IVAR units, but I found that if you have a shelf installed at the very top of the lower unit, the vertical posts can sometimes interfere with the shelf or the mounting pins. The…
I already had a Resmed AirSense 10 with F&P mask. As I am travelling quite frequently, I bought a Resmed AirMini. And for the price... you cannot use the masks you already have ! And I am not using the HumidX system. I found a few…
I printed in Elegoo PETG, dual-color on Creality Hi. PLA will work also. 25% infill. You need to print at least 2 of them (or 4 if rewinding to/from 2 Elegoo spools.
A simple adapter from quarter inch thread to Iphone 16 Pro. With hexagons!
This is my first model I ever attempted to design before I even got my own 3D Printer. My car's cupholders never fit my LTT 40oz waterbottle and I wanted to make something to get it to fit instead of just using someone's elses design.…
Tested some cuts for a solid fit --- you dont want a leaking behind the kitchen island :O
The original design is a great way to extend the height of IVAR units, but I found that if you have a shelf installed at the very top of the lower unit, the vertical posts can sometimes interfere with the shelf or the mounting pins. The…
Had to scale to 101% on my prusa Mini to fit on 80mm PVC Pipe. Check your tolerance the model is exactly 80mm Drilled holes for M4 inserts
Model 15° angle Attach from top or bottom of light Female Quarter Turn (Twistlock) compatible with under-side of many out front bike computer mounts Printed with support.
Wanted a way to mount a SKR Pico in an Ender 5 and Ender 3 so this little bracket will let you mount the SKR Pico in most Creality printers.
