Liczymy pasujące modele…
Installation: Just push it on the table leg and it should snap into place. Print- Settings: I printed it with 0.25mm layer height and 10% infill Anything else: If you need anything else or have ideas for improvements, just dm me ;)
Do you own IKEA but wish you had a better way of holding your headphones? Well have I got the solution for you. Introducing: this model. Printing Instructions: If I'm being honest, I probably could've designed this to be easier to print.…
Hello there. Long and hollow table legs may cause some wiggling during the time, especially if you use them on long tables. This is a leg brace for IKEA ADILS table legs (or any other 40mm legs) that adds stability. Uses 60x24mm mortise…
This is my design to mount a IKEA Adils leg in a table. The inner hole is only a hole. You have to screw the leg manually. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.16 Infill: 25%…
if u want to get higher with your table to clear another IKEA structure, this is the way.
Use 4 of this clamps to fix a board to a table using the 4 ADILS table legs from IKEA. With my settings an printer, this is a good fit, holding the board secure in place. But I wouldn't use this board to hold a collection of medieval…
Used leftover adils legs for table mounted shelf. Flange is for holding the shelf with variable height. Bottom holes are 5mm, side holes 7,5mm (for M8 bolts). 41mm diameter hole (adils legs are 40.5mm) so 0.5mm clearance 15% infill, 3…
Simple 40 mm spacer to raise the IKEA Lagkapten / Mittcirkel / Alex / Adils Desk. Happy printing :) Changelog Date Version Type Comment 2024-03-11 V1.0 Release
I made two models, one with a small space for cables and one without space (directly connected). I hope you enjoy the model.
60mm spacer for IKEA ADILS desk leg. Requires M8x30 bolt and M8 coupling nut (see picture). First insert bolt, then nut. Print instructions Resolution: 0.3mm Top/bottom layers: 3 or more Perimeters: 3 or more Infill: 30% Rafts: No…
Hi 3D printing friends! These are table support brackets that I used to attach my Ikea table (Linnmon, Item 16353)/legs (Adils, Item 22724) to the wall to limit my printer from shaking the table. The Bambu Lab X1 Carbon moves quick and…
The Ikea LAGKAPTEN / ADILS is too wobbly and short. This model will fix both of these issues while being sturdy and aesthetic. The print will take around 4.5 hours to finish one foot or around 22.5 hours for all 5. Be cautious of warping,…
Extension to IKEA Adils legs to use with Lagkapten desk top when used on top of a kallax unit. Adils legs are designed to be used with mounting kit from ikea, so when you do use it laying on top of your kallax unit instead, you are about…
Wanted a rolling light workbench for crafts so I modified my IKEA Adils table leg to add some office chair wheels I picked up at Home Depot (7/16 stem). The adapter is held on by the original pad. The adapters are quite a tight fit (I had…
Feet to raise the height of an IKEA ALEX desk by 8cm (f3d file included)
Simple Cable Clip for the cheapest Ikea Table Category: Household
Printer shaking your desk? Secure this to your wall and around the leg and it will help reduce the shake. This is also designed to hold the desk about 1cm away from the wall so you can run cables behind it. Honestly only 1 or 2 will be…
I tried another model for IKEA ADILS extensions but they were completely straight sided (no taper) which worried me that they would not be very stable if subjected to a sideways force. So I designed my own - these are tapered so should be…
I created my own IKEA ADILS Desk Cable Organiser Full Set for everyone, who need simple Cable Organiser to IKEA Desk :-) I tried to design a very minimalistic and simple design of my IKEA ADILS Desk Cable Organiser for desk / table leg of…
A simple, useful hook for an IKEA Adils table leg. Slide the hook onto the leg from below, then, if the fit isn't tight enough for you, add an elastic band across the rear arms. I use the hook to hide my PC's headphones and like that it…
Alex Riser : just put it over the original feets and fix them with screws. Adils Riser: just put them over :) Printed in PETG-CF
IKEA ADILS - Extender 60mm Sufficient to clear Ikea Kallax (under the table) Printing No supports needed. Print all parts with the bottom down to ensure a simple print. Example print Clas Ohlson generic white PLA
Easy to print heaset / headphone rest with original IKEA screws on the table. You don't need any additional parts. Print instructions 5% infill is enough Changelog: 22.03.2022: One part design (no more cones needed) add right version
A printable locking bracket for joining together IKEA Linnmon/Adils based desks together so they don't move apart when working on them.
This is a spacer that snaps onto the IKEA ADILS table leg. It is used to create a constant gap between the wall and the tabletop. It is also intended to prevent the table top from accidentally hitting the wall. I took inspiration from…
This hook was designed to snap-fit onto IKEA Adils desk legs, allowing for enough strength to hold headphones securely without the need for screws or clamps . Printing The hook is easy to print without any supports , with the only special…
A small snap on hook I designed to hold my calipers and some files along the leg of my IKEA table.
English : I created this Ikea Adils desk stand extension (or other 40 mm diameter stand) to raise the desk by 45 mm. Français : J'ai créé cette extension de pied de bureau pour pied Ikea Adils (ou autre pied de 40 mm de diamètre)…
Alignment jig to use with a Ikea ADILS table leg plate. You can use this to predrill a table top or just mark the location of the table leg. I used this to replace my cardboard Linnmon tabletop with actual wood. STEP included if you need…
These are clamp-on brackets for IKEA ADILS legs (or other 40mm tube legs) with holes to allow you to attach some planks or a piece of plywood across the legs, hopefully making them more stable and less wobbly. To be candid, I have tried…
English : A cable entry designed for IKEA Adils office feet (or other foot diameter 40mm). You will need an M4*15 nut and a bolt to tighten the clamp. Français : Un passage de câble conçu pour les pieds de bureau IKEA Adils (ou autre pied…
Not technically a remix since I completely redesigned this using Fusion360. Although to be fair, it was fully inspired by https://www.thingiverse.com/thing:1656880 , so I'll give remix credit. I wanted something I could use to support the…
Created for the 35mm desk height LINNMON / ADILS IKEA desk. Headphone Band support is 35mm There is about a 0.5mm gap to allow blu or white tac to hold firmly in place to avoid scratching.
Just a little make for a clip to hold 2 linnmon desks together with adils legs. I was getting quite tired of having to realign them every time i sat down. Excuse the quality of the print, did it in "rough n ready" mode for speed. No…
Clip on cabel channels for IKEA ADILS. You need two of each, the ones with the little cutout go on the bottom and the top. I printed it in Prusament PETG at 0.2mm layer height, no supports or brims needed. A single on takes ch. 10-11…
Kabehalterung/-Clip für das Tischbein IKEA ADILS mit ausreichend Platz für ca 2 bis 4 Kabel.
I have found a headphone hanger for the ALDIS table but i was getting dust on the them, so i designed inward facing so the headphones are hidden under the table ;) Problem solved.
Custom Foot Cap for the Ikea Linnmon/Adils Table. Just take an M8 Hexscrew of your desired Lenght, and you're good to go. -I took an M8x45mm Screw -My desired Tabletop height was 76cm If you want your Table to be higher than 80cm you…
This is a clip for an Adils leg from IKEA for use with the Underware cable management system. I basically just remixed an existing clip for the legs and slapped a “Small Thread” on it from multiboard.io. This will allow you to mount the…
Model printed in ABS at 0.2 mm layer height with 6 perimeters, 4 top layers, 4 bottom layers, and 25% infill. The print was paused at layer 80 to insert an M8 nut.
A simple Extension for IKEA ADILS Table legs, just slip on the adjusting screw on the bottom, its a tight fit, some glue may be necessary. Adds 25mm and a good grip for adjusting the height. Printed in PETG, 3 perimeters, 5/5 layers…
The following elements are necessary to carry out the assembly: 1x - M4 screw 1x - M4 nut
I printed it with PETG and it holds up great.
Bolt on headphone holder maybe even backpack. U need 2x M4 nut and 2x M4 20mm bolts with imbus head or for flathead screwdriver. M4 nuts fit is snug but it wasn't hard to push them in place. Printed without supports from PLA 15% infill,…
nuzzle 0.4 petg black artillery sidewinder skirt no support
Store the legs of an ikea table attached to the table for easy storage and moving! No supports required.
Adils extender 80mm A leg extender created because I couldn't find a 80mm one that would print fast and as simple as possible. In the first photo is the orientation it has to be printed (it has an internal chamfer). I advise using PETG or…
This bracket snaps on the bottom of IKEA ADILS desk legs to provide a comfortable space to the wall behind the desk. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.14 Infill: 30 % Filament:…
30mm extension, IKEA Adils. Keeping the original adjustable foot. I used 25% fill, 6 walls, 4 bottom, 4 top. Add a pause at the end off the nut (8mm) space. Nut size : 15mm tip to tip, thickness +/- 6.5mm
IKEA ADILS Collection Basically, a leg clamp with different attachments for hanging or storing various things. It can help you make the most out of the vertical spaces underneath your table. Print Settings: Infill: 40% Resolution: 0.3 mm…
I needed to raise my Ikea tables about an inch (26 mm), which was at the maximum extension of the screw-in feet, leaving the tables extremely unstable. So I created this simple riser to cup the feet. Because this is a practical print that…
An extension for the Adils leg from Ikea. I wanted to retain the adjustable foot at the end. YOU WILL NEED AN 3/8 INC HEXAGONAL NUT!! I printed one from the Massive Nuts Collection from @SpaceSway Just add a pause at the end of the hole…
I loved the standing desk mod, but I wanted to add a bracket so that I could have my 3d printer below my desk. This gives me clearance for my CR-10 .3mm layers, 3 walls, and 40 infill with 2 gradual steps. Print Settings Printer Brand:…
Parametric STEP files are included for compatibility with other square wood planks. Print with the round part facing down; 5 perimeters are recommended. The hole in the round section enhances strength by reinforcing perimeters rather than…
Ikea Adils leg - powerboard (HPM) mount For older 5cm wide legs designed for 5mm zip ties
Simple and usefull skateboard hanger. Fits perfect for 60cm desk. Printed it with Ender 3V2, PETG, 0.6mm nozzle. If you want to use PLA you won't be able to just push it on leg, but I guess sliding it from the bottom will work. To…
I designed this table leg holder to store the legs of a side table. Two holders are required to store four IKEA ADILS table legs. I mounted the holders under the tabletop to make storage as easy as possible. I printed them in PLA using a…
Hi folks, My desk is far away from a power supply, so whenever my wife comes into the room, she always blames the same thing. The cable looks horrible. So, I designed a way to hold it in place behind the ALDIS IKEA leg. The cable is a…
NO MORE SHAKEY IKEA TABLE! This wall anchor uses 3 screws on the Adils leg to anchor your table to the wall. ~1in or 25mm spacing from wall. Wall anchor screw holes are 5mm in diameter with a 9mm diameter recess for button head screws.…
I created leg clamps for Adils. I wanted to rise my computer to make vacumming easy. You'll need some M4 screws and nuts to clamp together two parts, one in the inside and one in the outside. I use threaded inserts to screw shelf bracets.…
Model printed in ABS at 0.2 mm layer height with 6 perimeters, 4 top layers, 4 bottom layers, and 25% infill. The print was paused at layer 80 to insert an M8 nut.
I designed this table leg holder to store the legs of a side table. Two holders are required to store four IKEA ADILS table legs. I mounted the holders under the tabletop to make storage as easy as possible. I printed them in PLA using a…
Feet extension for my table. The legs did have an adjustable leveler but it was still not enough to raise it to the size of the other table I put on the side so I made this 4cm leg to put under the legs. Fits perfectly and has a 1cm wall…
I extended the hook part by 4mm so that my headphone can take up comfortable space.
Merged together the Multiboard "8mm - Mounting Offset Snap - DS Part A" with the IKEA ADILS compatible leg bracket to make cable organizing under the table easier. Use any M3 screw longer than 10mm and an M3 hex nut.
I made this bracket to hold up a drop leaf table to give it more support. Since I was using standard Ikea legs, I wanted to use the existing screw mount and just needed a bracket to reasonably hold it in place (depending on the…
Frustrated by how wobbly the IKEA table with ADILS leg, I created this support to reduce the wobbliness. The slot might be a slightly lose / tight depend on your printer and materials. Leg slot is 41 mm, you can adjust the slot diameter…
Update, 27th January 2019 Added a version with two screw holes for mounting to underside of shelf This is the preferred version as both sides are now more robust. Update 30th October 2017 I've added a revised version with the upper screw…
IKEA Adils table leg, which is reused wil old monitor arm components to turn it into a new monitor stand. This stand holds 2 monitors in an stacked position, as well as my DELL XPS 15 laptop and DELL TB16 dockingstation. The goal was to…
I wanted to keep the water bottle and coffe cup off my desk, and had a spare IKEA Olov leg lying around. I created 2 areas where a bottle or cup could be placed. The screw holes are M5 screws, and they are 16.5mm deep. In the model there…
60mm spacer for IKEA ADILS desk leg. No bolts or nuts required, plug and play. Print instructions Resolution: 0.2mm Infill: 30% Rafts: No Supports: No
Desk hook designed to effortlessly hang a backpack/bag under an IKEA desk with ADILS legs. The hook is mounted using 2 of the 5 existing screws, so there's no need to modify anything. Print it on the flat side, 4-5 perimeters recommended,…
I needed a small table to fit a cordless phone, so i made on with a spare IKEA table leg i had. Specs: table top 150mm Diameter Materials: table top : PETG (due to the small little inserts for the screw holes, use petg or abs, PLA's layer…
