Liczymy pasujące modele…
Overview A fully printable, fully functional printable harmonica in a simple 3-piece form factor that clips together - no fasteners needed! The design features swappable reed plates which set the playable notes. The attached reed plate…
This is the Harmonica. A very easy to print model. Building instructions from top to bottom Top Cover Blow Reed Plate 2 Blow Reed Plate 1 Middle Part Draw Reed Plate 2 Draw Reed Plate 1 Bottom Cover All connected with 4 M3X18mm screws…
I discovered that there is no harmonica holder on Printables. So I designed one. This is just a simple harmonica holder but it should work with most of the diatonic harmonicas. I checked it with my Hohner Silverstar and some unbranded…
Blaster overview The Thumper is a shotgun Nerf blaster using a harmonica clip, top slide and T pull prime, and swappable ammo modules! Sellers Hardware is available from these sellers: OutOfDarts:…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This model I made to replicate the echo phone from the 1930's. I designed it for a Hohner harmonica but i'm sure it would fit others. remixes are welcome!
I printed mine in PolyMaker's Polywood PLA, but I am sure PETG would last longer.
Designed for a Swan blues power harmonica, internal dimensions 21 x 30.5 x 110mm Use a piece of filament for the hinge pin, you may need to clean the holes out a little. There is some fine detail around the top so don't print at lowest…
harmonica box Category: Organization
This simple harmonica case is designed for a rigid outer material (PLA, PETG or ABS) and a soft inner material (such as TPU) for better protection. It was custom-made fora the Hohner Marine Band Classic 1986 harmonica, other ones of…
My kids didnt like that the clear case that the J'adore Campfire Harmonica (Target Bullseye Playground) came with doesn't stay shut, so I quickly threw this together real quick. This is my first ever print in place design, so bear with…
It would be nice if you post your make. Thank you
I have had this blues band harmonica since I was a little kid. I wanted to make a nice sheath to protect it, but I also wanted it to have some custom details. I made the blues band logo as a stamp to emboss the leather and then made a…
harmonica in link below https://www.amazon.com/dp/B07VG6HD98?psc=1&ref=ppx_yo2ov_dt_b_product_details prints as one piece, use a brim, infill should be about 60-100 percent for strength. the overhang for the outlet holes may be too…
Lampshade harmonica, compatible with Ikea cord set HEMMA, print in vase mode.
The model was redesigned to look like a harmonica
I needed somewhere to put my harmonica microphone when I'm not playing, so I cadded up this model. It's a short and easy print. Print it on the front facing side on the build plate and a little bit of tree support under the flange. I used…
Add a cheap harmonica, zip tie it under a friends car and let the laughter begin
Light box to optimize the response of a harmonica Leuchtkasten zur Optimierung der Ansprache einer Mundharmonica I used this LED-stripe from Amazon inside: https://www.amazon.de/dp/B08KM6FCQB?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 In the…
Keep your harmonicas safe, dust-free, and ready to play with this 3D Printed Gridfinity Bin , meticulously designed to store a Casha Blues Harmonica and a Hohner Marine Band Harmonica —each with its protective case. This modular storage…
Quite like the Thumper indexing mechanism, except when I'm trying to reset it back to the start. Didn't like having the clip drop away either, so I split the cam arm into two pieces and added dovetail joints to them. It flexes using a bit…
This is a replacement mouthpiece vintage keyed harmonica. I have had this for many years and somewhere the mouthpiece was broken. My grandson is fascianted with it so I made a new one.
This is a replacement comb for the Hohner Marine Band Deluxe harmonica, modeled from precise measurements taken off the stock pearwood comb. Note: this is untested. I haven't confirmed fit or seal quality against a real Marine Band Deluxe…
A simple harmonica holder for gridfinity. Holds four harmonicas vertically (on their sides)
Maybe you play in an orchestra or at concerts and you dont want to put your harmonica or recorder flute on your chair. I've got you covered! Meet my harmonica or flute recorder holder :D With the inlays both instruments are safe and…
This simple harmonica case is designed for a rigid outer material (PLA, PETG or ABS) and a soft inner material (such as TPU) for better protection. It was custom-made fora the Hohner Marine Band Classic 1986 harmonica, other ones of…
Maybe you play in an orchestra or at concerts and you dont want to put your harmonica or recorder flute on your chair. I've got you covered! Meet my harmonica or flute recorder holder :D With the inlays both instruments are safe and…
I needed somewhere to put my harmonica microphone when I'm not playing, so I cadded up this model. It's a short and easy print. Print it on the front facing side on the build plate and a little bit of tree support under the flange. I used…
Simple yet functional dishes for a soap. Easy to print. For better bed adhesion, use a brim. It is easy to peel it off a
Once Upon a Time in the West - Harmonica (Charles Bronson) - 1968 3D printable model.
