Liczymy pasujące modele…
LICENSE Copyright © Herr Brain 2023. This source describes Open Hardware and is licensed under the CERN-OHL-P v2 . You may redistribute and modify this documentation and make products using it under the terms of the CERN-OHL-P v2…
Those who have used these vapes will find out they should be stored vertically. However, they are too skinny to stand much on their own. This adds a little bit bigger of a foot print without taking up much more pocket space. It was sized…
The power button on my Cycliq Fly12 CE bike camera wore out and fell off, leaving the circuit board with the switch exposed. Rather than try to exactly fit the hole (which I don't think I could have made waterproof), this replacement…
Après une chute, la boite d'origine à lâchée. Ayant voulu garder le système de rangement avec les annotations d'origine, j'ai modifié une boite vue sur la toile pour remplacer la boite HS. Imprimé en PLA. j'utilise des bouts de filaments…
The first installation of a cycliq camera will require quite a bit of force, in my experience. That rounds off the edges of the lock bumps. After that, it seems to be nice & firm I printed flat with a 0.6mm nozzle, no supports, 0.3mm…
I have a Cycliq Fly6 generation 2. It's the one which uses a pair of rubber straps to attach to the seat post. But the rubber straps keep falling off every time I remove the light from the bike. So I've created this mount to attach…
This is one of my brackets for my Cycliq cameras. Mount style ‘C’ refers to the bolt counterbored straight down from the mount face, and with the locating pyramid/pin hole. Designed for an M4x20 SHCS This bracket can be used with my…
Various versions of a tail mount for an Old Man Mountain Divide bike rack for rear-mounted lights, cameras, etc. Works with GoPro, Cycliq, and a wide variety of other bike accessories depending on which version here you choose. Strongly…
This adapter is designed to work specifically with my 1/8 Turn Mount Bracket C (that actually connects to the camera twist lock). This adapter is just to mount that bracket on the handlebars, with the intent being that this adapter can be…
Peut être pratique pour pré visser rapidement un écrou 4 pans, a été créé pour tourner des morceaux de bois Les tailles de bois les plus communes ont été prises en compte Imprimé en PETG - buse 0,6mm - Remplissage giroide / classique 60%…
Designed for 36mm diameter stem at an approximate 10 degree angle. Should fit smaller stems with a buffer such as electrical tape. No supports required when printed on flattest faces. Requires: - 8 x M3 threaded inserts - 4 x M3x10mm…
I have a Cycliq Fly6(v) rear bike light camera. This is the version with the velcro strap, aka their third version. It's great. Until I needed to mount on my bike that has a rear carrier- it wasn't possible to get the light close enough…
The size (especially on the back) could use some fine tuning, but .. it's just a storage box.
This device NEVER WORKED so it was on my desk a lot while I tried to test it and hope that Cycliq would stand behind it. They didn't.
Coffret pour ranger une clé à cliquet avec son couvercle
Simple stand for Select Cliq battery and up to 3 pods. 4x2mm magnets are optional.
Le plot de verrouillage de la douille sur ces cliquets à tendance à s'user. Alors le plot est évacué par le ressort et le cliquet n'a plus de verrouillage. Cette pièce permet de le remplacer (à condition de n'avoir pas perdu le ressort).…
The rubber feet on my Go Chair(Cliq) fell apart do to the rocky beaches on our lake. So the chair would just sink through the rocks or sand and it would be unstable. After a few years I contacted Cliq and they ended up giving me a brand…
I have had several of the feet on my cliq chairs fall apart. While waiting to hear back from the company on possible replacements I decided to just try to design my own replacements. They are intended to closely match the size and look of…
HauteWorks Cliq Bicycle lamp bracket clip replacement Customer had a broken bracket clip for his bicycle lamp and ask for a 3D printed replacement. So after a couple of tries here it is with the proper fit. You will need the original pad…
A set of arms and adapters for you to do weird things with your GoPros, Cycliq, and compatible cameras. I'm not here to judge you - go crazy! I had a specific use case but figured others might be able to do some interesting things as well…
I printed face down, with supports on build plate only. I’ve made the nubs that lock slightly taller on the STL than the 3MF & GCODE. Tinker Cad File should you need to remix. https://www.tinkercad.com/things/87fy4U8ngXs
réalisé avec une K1 a 40% qualité 0.16 avec support ; le noir du logo est réalisé au marqueur
The rubber feet on my Go Chair(Cliq) fell apart do to the rocky beaches on our lake. So the chair would just sink through the rocks or sand and it would be unstable. After a few years I contacted Cliq and they ended up giving me a brand…
Due to having aero handlebars, I've repeatedly had issues mounting my Cycliq Fly 12 front camera and light. I'm not racing anymore but am comfortable with my setup so I didn't want to buy anything new. I tried the clip design from…
![[v2.2] QtQwiicCliq - DIN mount for Stemma Qt/Qwiic/Thing Plus/Feather/Raspberry Pi Zero](https://media.printables.com/media/prints/512753/images/4155220_203b39bf-2534-4a34-bd72-fcf5323b0e6e/pxl_20230625_030245459.jpg)
