Liczymy pasujące modele…
Does your Thanksgiving tablescape need a touch of traditional autumnal flair with a fun, modern twist? This gorgeous holiday centerpiece is the perfect conversation starter. Use it to change the subject if any uncomfortable political…
This is a very simple piece to make a rounded corner so the ball does not get stuck. There are similar corners that I have printed, but I found them too big and blocking the scoring zone. These corners is easy to attach, does not block…
I needed to orient the camera of my intercom differently so I modeled a new one
A small, fast to print thing that cushions the corners of sharp objects, print in TPU or other flexible materials. Check out my other models! I make fidgets and useful things.
This model allows you to use any 1u 10 inch mounting plate as the cross member in the Labrax 10inch rack. This means a smaller printer can be used and also allows for new mounting options at both the top and bottom angled areas. Total…
🐱Please check out our other models.🧩 https://www.printables.com/@ManabunLab/collections/2268829 Thank you for viewing. The sale, sharing, and modification of data is prohibited. If you wish to sell prints, please obtain a commercial…
This tool has a cube at one end for grouting inside corners, and a sphere at the other end for applying caulking/sealant/silicone. Design features Two-in-one tool saves space on your hard disk. Different sizes available. Printing…
This model is compatible with the lego system.
Very good instructions from Dave Wilson. Thank you. https://www.printables.com/make/2339640?comment_id=2339640
I wanted to light up my HomeCube with a white LED strip and turn it on and off using a small power switch from the outside of the HomeCube enclosure. Therefore, I modified the original base foot corner so that my switch fits perfectly…
My sister asked me to print these corners for her. I looked around and found a model on Thingiverse. That was great, but I had some trouble printing them, so I took that model and made several changes to print it reliably without support.
Wall art / topper / coaster / keychain: Unicorn - 24 cm, 10 cm, 5 cm (four colours)
Wall art / topper / keychain / coaster: Unicorn - 24 cm, 10 cm, 5 cm (three colours)
Corner bottle dryer for a corner sink. The bars width are 60mm (left) and 70mm (right). Please adjust to match your sink! Mine has a weired joint in the back thats why there is a whole in the model. Main part: Printed standing with tree…
Wall art / toppers / keychain / coaster: Alicorn - 24 cm, 10 cm, 5 cm (three colours)
My printer stand is built from extruded aluminium ftubes and plastic corner joiners. All available cheaply at Bunnings. When the printer gets up to speed the while stand sways back and forward. These brackets make a huge difference in…
A Multiboard dual snap that allows you to create 90° corner tile multiboards without using brackets. This minimizes filament use and space required (can be placed on tight corners, walls etc). Also keeps the tiles available for other…
🧩 Model Title Popcorn Bucket --- 📌 Description. Experience the perfect blend of retro charm and modern innovation with my 3D printed popcorn bucket. Ideal for movie nights, parties, or a cozy evening at home, this medium-sized bucket is…
Modern Design Square Tray With Rounded Corners print it in black: it's gonna look nice
I wanted a horizontal mount for the SKR Mini E3 V2 to act as a secondary MCU for Tronxy X5SA Pro build. It needed to be in the front right side so it could be hooked to a display. Printed in PLA using Voron print specifications. Supports…
Does your Thanksgiving tablescape need a touch of traditional autumnal flair with a fun, modern twist? This gorgeous holiday centerpiece is the perfect conversation starter. Use it to change the subject if any uncomfortable political…
J'ai dessiné sous Fusion 360 cette lampe licorne pour ma nièce. Je vous mets en PJ le modèle sans le prénom . Pour la licorne je me suis basée sur cette image Il faut imprimer les différentes couleurs de la crinière de la licorne…
I printed two of the 1:12 size, which makes it just a little too small for Skittles and M&Ms. One in PETG and one in PLA. The PETG supports removed a little less clean, other than that, supports off, then snap the legs down and up and…
A replacement hopper for the Smart Grinder Pro, I was unhappy with how small the opening and volume of the hopper was and I am not a fan of weights to prevent popcorning. It is sized to fit this bellows at 100% size…
This bracket can be used to reinforce joints in tables, frames, or other furniture. I printed with PETG. 0.24 layers. 3 walls. 15-25% infill. One side is 7cm long , other 3cm.
Christmas Corner Snowflakes change the layers to change the colour combo, takes ~3hrs to print. Fun piece to give instead of Christmas card.
The Soundboks Gen 2 speaker has hard aluminum corner bumpers, unlike the rubber corner bumpers on the Gen 3 and Gen 4 speakers. These hard bumpers are prone to scratch and dent. This model is designed to add a bit of squishy TPU…
It is 180mm deep and 120mm high but you're welcome to make it your own size I printed it with 15% infill and PLA. It took 2h45min on the Ender 3v3 Plus
I designed this part while building the SICCO Filament Heater/Dryer DIY Project for my Prusa XL 5 Head printer. The project calls for 30x30 aluminum extrusions (black) and requires 3 way corner cubes, which are usually silver, and need to…
Curved corner tray with Honeycomb walls, for utensils, or anything you want to store and have it fit in a corner. No supports needed. resize to your liking.
Corner version of safety razor and oral B IO charger tooth brush.
This design is for anyone looking to ensure your structure doesn't move much during it's use. I don't know for sure HOW much this helps but it does help just slightly and only requires about $4 more of hardware.
Corners easy assembly a light frame for several applications. Green house, 3d printer enclosure, dust protection cover, ect. … NO SUPPORT REQUIRED FOR PRINTING Wooden or aluminium beams 14,5x14,5 mm
Each month, a card corresponding to the change of sign will be released. You will find a simple version that prints with just one color change and you will also find a galaxy version which I had a little more fun with which mixes a…
Created to connect to a corner cubical framework to hide wiring.
2020 Connector 3 Way Corner Bracket EXTRASTRONG _Alu Profile Suitable for: Resize to adjust dimensions Warning: Dimensional Tolerance Notice Please be advised that final print dimensions can vary due to printer settings, calibration, and…
Hello there, I made this handle for my daughter since the original IKEA handle broke. She painted hers with melted cryons but whatever method is fine. Its easy to print and it works fine so far. The hole distance is 128mm.
Jednoduchá rohová konzola s rozmermi 43 x 43 x 43 mm. Rozmer vnutorneho otvoru 8,8 x 22 mm. Ak sa ti model páči klikni na lajk (srdiečko) a keď ho vytlačíš odfoť a daj hviezdičky. Ďakujem. Simple corner bracket with dimensions 43 x 43 x…
In memory of Ken Block . Summary This is a model of a 1965 Ford Mustang notchback ( known from “[HOONIGAN] KEN BLOCK'S GYMKHANA SEVEN: WILD IN THE STREETS OF LOS ANGELES ”) in a kit card style. After printing, the model can be assembled…
To help tidy wiring for external monitors etc on the SV08. This clip simply snaps onto any of the corner pillars and has various sized wire clips that can be attached. Upto two sizes of wires can be attached to each clip. Alternatively…
They are designed for 8 mm thick boards, and add a 4 mm thick base or foot. Could be scaled in Z (or in XYZ) for other thicknesses. The undersides have grooves which are printed first and then bridged. Ensure the first bridging layer runs…
ENGLISH End cap and corner for Ikea Havstorp One end piece, original One end piece, for gluing One Corner You need to print them out as they are aligned. GERMAN Endkappe und Ecke für Ikea Havstorp Ein Endstück ist an das originale Design…
Hi. I've designed a corner cover for Baseus powerbank. Bottom and top of the case are opened for better heat distribution and access to ports. Sides fully closed. There is also an opening for a function button. THIS DESIGN COVERS CORNERS…
Dimensions Size: 39x39x36.5 mm^3 Sphere diameter: 35 mm Covers 30 mm of the corner in all axis Print —Tested for Crealty K1 Max w/ standard 0.24mm profile— Filament: Generic ABS—For impact resistance ABS is superior to PLA. Layer Height:…
Sturdy Corner Bracket with Ribbed Reinforcement – Heavy Duty for 2020 / 3030 / 4040 / 5050 V-Slot & T-Slot aluminum profiles Perimetric reinforcing rib for superior strength Optimized profile geometry – better resistance and easier…
This is a top hat for a Voron Trident 300 that I'm calling an Ascot because of the jaunty angle ;-) . This gives extra height for an umbilical setup in the rear yet allows a complete unobstructed view into the chamber while standing in…
Floor trim corners and ends Koncovky pro podlahové lišty SLK50 z Brena
new model new design kindly don't forget the support after printing you may need something to put under the back feet if the infill is not equal
Simple functional Corner Bracket 40x40x40mm with countersunk screw holes. print in place no supports needed. i would love to see your prints
The most stable result is achieved when the model is printed with the chamfer as the base surface. Suggestions for improvement are welcome Das stabilste Ergebnis wird erzielt, wenn das Modell mit der Fase als Grundfläche gedruckt wird.…
A simple decorative corner for a DM screen I made using 0.25" MDF sheets. Made in Tinker Cad.
This sanding block is designed for flat surface sanding as well as two specialized edge profiles for curved and inner corners. It holds sandpaper securely and is ideal for scale modeling, woodworking, and DIY tasks. The ergonomic shape…
Shingles scaled to 1/12 actual, arranged according to the installation instructions.
Should print without supports. Done some time ago, but if it gets popular i will redo the project with new design ideas. Part of my collection for furniture: https://www.printables.com/@MichaMietlins_755343/collections/3218237
This system is great for photographers, makers, or artists who need a reliable and portable lightbox setup. Add LED strips or diffusion sheets for best results. Features: Designed for wood cleat measuring 20×36 cm Works with 12 wood…
The ZG-204ZM sensor, which supports PIR and mmWave, includes a base with a ball joint that allows for angle adjustment. However, it can only be installed on flat surfaces, and the designs I found online allow corner mounting but sacrifice…
This bean bag toss game is perfect for passing the time at work or school! Print them as gifts or just for yourself, for some great fun! Cornhole is the name of the game in the US. Here are the “American” Rules of the game:…
🇹🇷 Kişisel kullanım içindir ✔ | Satış için Patreon'dan lisans alınmalıdır 🔑 🇬🇧 For personal use only ✔ | Commercial use requires a Patreon license 🔑 🌿 Modern and Stylish 3D Printable Vase Collection 🌿 This elegant collection of 3D…
Would you like to support my work? :) Check out my full catalog with exclusives, early access and commercial licences. — A little helper for your next BBQ. Stop getting greasy fingers from eating delicious corn cobs. The texture provides…
just a simple and effective box corners that you can use to make a custom box only m3 10mm screws needed and only 2 m3 25mm
It’s a connector for ikea skadis, to connect four plates together. Two next to each other and one on top of them also next to each other.
If you like what I do here, come visit my (German) Discord or my Facebook group. Discord: MX-creations Facebook: 3D printed Grow Tools & Accesories - free .stl this is part of SCROG-system MXG-2 (part 3/3-aditional parts)…
This is an upgrade to the 5 corn coins in Tzolk'in. I didn't like the idea of just making a larger corn and I didn't want to do a large basket full of corn because I wanted it to still fit in my insert so I designed this as a coin…
Simply the 5-120mm jig by Bertrand L. cut in half for smaller printers.
This model is ideal for decoration, gifting, or adding a touch of humor to any space, like an office desk or home shelf. It's an excellent choice for dog lovers and those with a playful spirit.
A new 3D figurine generated by AI, a unicorn. Do not forget to LIKE, to download and to upload your makes, thanks ! Powered by Image-to-3D from MakerWorld (https://makerworld.com/makerlab/imageTo3d)
Verhindert sicher das Herumspringen der Bohnen beim Mahlen. Gedruckt mit ABS.
This OpenSCAD code is just a few lines that will make a cube with rounded corners. It works very like the ‘cube’ statement. This code is a module so, instead of the call looking like “cube ([123, 234, 345]);”, the call would be “nice_cube…
The model measures 230x208x4mm but can be scaled to suit your printer. Care is needed when scaling the height of the model as colour changes will be affected. The model was printed in PLA filament with a 0.4mm nozzle, layer height of…
Place one Corner Strap Clamp Jig on each corner of a box or frame you are wanting to pull together and tighten it up with a ratchet strap. Print on the flat side with supports touching buildplate. %15 infill is fine no brim or raft needed.
A simple template to create perfect corners with a handheld router.A simple template to create perfect corners with a handheld router.
A set of five reinforced 3D-printable corner brackets designed for strong and precise 90° connections. Each bracket has a unique industrial design with ribs and oval holes for adjustable mounting. Features: Dimensions: 50×50×20 mm Wall…
This is a McGraw Tower-inspired lamp case designed to house a standard lightbulb. The hollow structure allows light to shine through while maintaining a clean architectural aesthetic. Print Time: 7-10 Hours (400mm/s avg print speed) Layer…
A small, fast to print thing that cushions the corners of sharp objects, print in TPU or other flexible materials. Check out my other models! I make fidgets and useful things.
Acorn Storage Container with Screw on Lid Filament Used: Body: Inland Brown High Speed PLA+ Lid: Inland Light Brown High Speed PLA+ Inland High Speed PLA+ on Amazon Printer Settings: Print Time: 6 Hours 11 Mins Print Temp: 230°C Bed Temp:…
This is an experimental model of a “Curved Cornett” from the 1981 book The Amateur Wind Instrument Maker, by Trevor Robinson. There's a lot of details missing from the very rough drawing of this cornett. I used pixel estimation to…
You might want to adjust the model to tune the depth of the indent for double sided tape. Put some double sided sticky tape on the square to adhere to the mat.
Edit : I added infill modifiers to the Bambu files to make the object more durable. However, I still recommend printing the main body in ABS to maximize strength. Make your life easier with this acorn-shaped nutcracker. Simply twist it,…
These are stands that connect to the Top of Snapmaker U1, 4 stands create a base that you can put a low cost Top Cover over it. Feel free to adjust it to match your need. There are 2 files: 1 with 1 stand only. Another is 4x stands for 4…
I created this modular holder for GunplaMark's Ultimate Cereal Filament Drybox, because I never liked the hygrometer hanging on top of the filament exit port (unstable angle against gravity). Instead, this mod allows to put some…
Craft your own custom boxes with square walls and effortless assembly. Don't worry about polarity, use a screw driver to remove and reorient the magnets in the clamp. Mix and match polarities to suit your needs. Print in 45 degree angle…
Put your IKEA STYRBAR or SYMFONISK Remote in a corner. Remix of "Better Ikea Styrbar wall mount" by @pipsel_222257
I have a paltform in my room that has a leading edge trim of 1" outside corner. The wood is not finished (stain or sealant) so I didn't want to use command strips, adhsive, or nails/staples. I designed these clips to be easy to clip on…
In memory of Ken Block . Summary This is a model of a 1965 Ford Mustang notchback ( known from “[HOONIGAN] KEN BLOCK'S GYMKHANA SEVEN: WILD IN THE STREETS OF LOS ANGELES ”) in a kit card style. After printing, the model can be assembled…
This 90° corner clamp is a sturdy L-shaped tool designed for accurate right-angle alignment in woodworking, furniture making, and general workshop applications. The bracket consists of two equal arms forming a 90° angle. Both arms feature…
