Liczymy pasujące modele…
Da ich das Sprührohr meiner WD40-Dose verlegt habe, musste schnell ein neues her. Vorhandene Modelle habe ich ausprobiert, aber sie haben leider nicht gepasst. Das Sprührohr ist ca. 80mm lang und hat einen Innendurchmesser von 1,5mm, der…
I liked the design by Andreas Gohr and changed a few things to my taste: chamfers on the mounts one mount with hex nut trap, so now two different mount pieces exist only 1 mm gap between the mounts that disappears if screwed tight BOM is…
Cup-holder style WD40 holder for the famous honeycomb storage wall. It's for the 100ml bottle (Diameter 45mm) What is needed? 1x print fille ‘WD40_Bottle_Holder’ 1x ‘insert-empty’ (from original Honeycomp Storage Wall ) How to print? very…
Made to fit the splines covering the spindle. Use it to remove the pedal axle from the pedal body.
Simple holder with multiboard inspired designs to cut down on plastic used. Uses 2 push fits on the back, which requires these snaps:…
I've often managed to lose the straw for the WD40. That's why I created a clip that definitely got rid of this problem. Hopefully it will help you too :-)
Holder/s for WD40, 3DLac and other sprays. Inner diameter optimized for 65 or 53 mm sprays. 3mf and bgcode for 1 or 3 pieces. Any number of pieces can be made. It is also possible to achieve a different diameter by adjusting the scale.…
The VOID40 is a 3d printed, handwired, 40% ortholinear keyboard running QMK Firmware on a Pro Micro controller. The case is designed to fit the bed of a stock Ender 3 when the parts are rotated 45 degrees and the skirt/brim is disabled in…
This holder is to hold my WD40-Sprays 2 Ways can on to my HSW wall. But it will also hold any can or object that is 65mm wide or smaller. There are files to support HSW Mounts using full hex snap Multiboard Snap Multiboard Stud Model also…
Źródło oznaczyło ten model jako treść 18+.
Replacement cap for 400ml WD40 or similar containers. "clic" and it's in place ! If this becomes too hard to remove, slightly scale it up finely (like ~0.1-1%). Recommended settings \_/ Ø 0.4 Layer height 0.2 Perimeters 2 Infill Bottom &…
Update 12.06.2025 : design update for better lid snap and more guideline -compatible sensor slot Small case that you can simply print (case and lid). The case is made to store a: SCD40 or SCD41 board (no pin header, Aliexpress example )…
Andonstar AD407/AD409 soldering microscope mount for Rode PSA 1 microphone boom arm. Re-use the thumbscrews from the original mount to attach this mount to the microscope, then attach to the microphone arm, see photos for my setup. PLA or…
T-Nut drucken mit PETG infill 100% ohne Stützen Düse: 0,4mm Schichthöhe: 0,2mm Die Fläche mit dem Sechskant auf das Druckbett. Zwischen Sechskant und dem Loch ist eine Drucklage um das Loch drucken zu können. Nach dem Druck einfach mit…
Use 2x M4 screws on backside. No supports needed.
WD40 staw holder 200ml can
I have a very small workshop, so I have to get creative with my tools. I am using the drill press as a rotary sander and needed a way to quickly attach dust collection. It works perfectly! If you want the same setup, just buy the sanding…
A simple Y adapter for gasmask hoses. No supports needed. Just print the parts and glue em together.
Drill press vacuum adapter for Bosch PBD40 including Bosch Click and Clean hose plug
A rd40 compatible gas mask breath restrictor. With a twist, you can controll the breathing resistance. It is meant for training purposes. For the outer part, supports are recommended.
Nozzle 0.4 Resolution 0.2 Support YES Raft NO
For collectors like me. A cheap and simple gas mask filter dummy. For display purposes only. No supports needed.
It ist for outdoor use and I will print it in ASA with 50 % infill outer diameter: 40mm inner diameter: 8mm high: 20mm fase: 45°
You need to use support for the bottom of upper hexagon, ideally tree (manual). Use original empty inserts. Hexagons are very tight, but I used superglue - better be safe. 260509 - added holder for 45mm cans, with slightly reduced…
There are great tripod screw mounts for cameras. There are interesting solutions for having overhead camera mounts for youtubers and twitch users. So let's use these solutions to free up space for soldering with the Andonstar microscope.…
Alternative replacement Grille for the USA Trains SD40-2 locomotive. These are the welded wire cage style with the 2 most common mesh "inserts". SLA Print. Print Settings Printer: Elegoo Mars Rafts: No Supports: Yes Resolution: 0.05…
Źródło oznaczyło ten model jako treść 18+.
Designed to protect the bulb of a Flashpoint Xplor 400 or Godox AD400. Clicks into the bowens mount and covers the bare bulb. I wanted something to replace the 2 piece cover it came with because it kept falling off and I didn't want to…
Shimano pedal service tool TL-PD40-BTL-27L a tool to disassemble the shimano pedal. Similar to the TL-PD40 tool. can be used in combination with a 44 mm bottom bracket tool. I use it together with the BBB/BTL-27L. V2 is for a tighter fit…
67mm Version of the wonderful T clip version by @DJ_Designs that fits the WD40 can
Overview Even if this mount is specifically for the Andonstar AD407 microscope, the mount may fit for other versions like AD409, AD302 and probably others, too. Just check if your microscope has a diameter of 35mm. If yes, this will work.…
Simple, compact clip in scraw holder for the 80ml WD40 cans. Sick of having the straw across the cap taking up tons of room. I used the same clip style as the lid but mounted it vertically against the can.
Adaptor for generic full face mask to mount 22mm medical filters. RD40 DIN If you can donate to support me, the donation will be used to help health workers and doctors Print instructions min 0.2 layer no raft no support
This is a simple extension bracket for the Andonstar AD407 microscope. With it you can put larger PCBs underneath it. I recommend you also upgrade the table. Should be an easy print, no support needed. I used 20% infill. For mounting you…
Compatible feet to raise bottom case clearance to 32 mm / 1.25 in. Recommended to print with the widest base section to the bottom and not add support to the overhang section.
The Turin SD40 is a good entry level grinder, but it's major draw back is the relatively large stepped grind size adjustment locking mechanism. This worm drive and dial gear replaces the original and allows for stepless grind size…
Tool for unscrewing Shimano M520 pedals. Also fits Bontrager Comp Road. ABS print, PETG might also be sufficiently durable.
Redukce pro namontování výškových reproduktorů průměru 36mm do vozu Nissan Navara D40. Pravděpodobně bude pasovat i do vozu Pathfinder R51.
Just your standard 120mm Fan Grill, stylized to match the Jonsbo D30/D40 top grill pattern.
A holder that holds a 100ml WD40 bottle. Printed in PLA with 5% infill.
If you like my design you can support me on BuyMeACoffee - https://www.buymeacoffee.com/kaushikbm -------- A very frustrating thing of WD40 smaller packs is that it doesn't have a proper holder for the straw they give along with. At least…
EDIT V2 Update: Had another crack at making it a bit less rough. V2 is a bit more refined with a more aggressive angle for the portafilter and rear clip to hold in place without the need for pads, front tab holder has a relief cut for a…
Hallo! Ich habe mir mal endlich einen kleinen Absaugring für meine Bosch PBD40 gebaut! Ich habe einen Schwarnenhals mit M8 Gewinde verbaut! Gibt es bei eBay oder Amazon in verschiedenen Längen Support habe ich nur von der Druckplatte…
Ring light attachment for the Andonstar AD407 soldering microscope. Can be printed without supports, place all models face down. Bill of materials Adafruit QT Py 2040 (https://www.adafruit.com/product/4900) Adafruit NeoPixel Ring 16 RGBW…
This is a remix it came from thingiverse here is link to file https://www.thingiverse.com/thing:5358828/files You will need longer screws to bolt on the the 4020 fan but all other parts that come in box still works. Print Setting .2 layer…
Držák pro spreje (vytvořeno pro WD40), možné využít pro podobný průměr základny. Vnitřní průměr 68 mm, vnější průměr a šířka 74 mm, výška držáku 65 mm.
I designed a WD40 can holder (diameter 54 mm) that can be mounted on a wall. It consists of two parts - bottom and top. Each part has a 3mm hole for countersunk screws. Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2 Rafts: No…
An upgraded SD40 tank, with more prototypical profile. There is no provision for a speaker in this tank. This tank mounts to the chassis the same way the stock unit does. The details are simple, like the stock tank.
I've bought the amazing GODOX AD400PRO with Elinchrom mount. But I soon realized, that I cannot use my Elinchrom deflectors anymore. The AD400PRO is missing the mounting hole. I've designed and 3d printed brackets on my Prusa i3 MK3 from…
Model prints in two pieces, these need to be glued together. Holder has few ventilation holes for better cooling, however it wasn't tested with extended modeling light operation. Be careful. This is the reason why I recommend to print it…
Made this model for a friend. Don't have a Navara myself, but tested the fitment. The switch holes are made to fit the switches that come with the Kings Light Harnesses. The 2 mounting holes are 4mm and designed to fit a 6Gx15mm screw.…
Ecken-Schutz D40H8 Zum aufkleben z.B. auf die Ecken einer Glasplatte eines Tisches.
One 2x2 Bin for two 100ml WD40 Spray Cans and 8 spray nozzles. The diameter of one can is ~45,5mm and spray nozzles 3mm
no supports needed updates coming soon WARNING: DO NOT POINT TOWARDS FACE
Spacer to center the common LED Light for the Andonstar AD407 / AD409. You can apply aluminium foil to increase the reflective area and improve the light. LED Light: https://amzn.to/3wUdy9R Boom Arm: https://amzn.to/4bOq6OE Microscope:…
Hose coupling for vacuum cleaner D40 - 42 PLA Nozzle – HF 0.4 Layer - 0.2 Fill 15% Perimeters >2 Supports Brim
I recommend to print with 3 perimeters and 30% infill, to be safe(-r). Shigematsu bayonet has it´s own seal on the mask, for the filter I use SBR 39x27x2 mm. Print with bayonet side down (thread up), no supports. Doporučuji tisknout 3…
I created a holder for the WD40 200ml for the skadis wall. Support is required for the hooks. Print settings: Infill: 15% gyroid Layer height: 0,2 mm Filament: Prusament PETG
Can Holder for Küpper Pegboard 45mm Spacing For Cans up to 53mm in diameter, for example WD40 Use 2xM4 Screws to mount
Adapter for dishwasher hose to 40mm (D40) sewer pipe. Needed this while I was waiting for a new kitchen sink to be delivered. So in the meantime I needed to connect the dishwasher to the sewer pipe directly.
Support à poser ou à pendre au mur pour un spray Ballistol ou WD40 avec son tuyau
This is a remix of the knog from this project https://www.printables.com/model/153460-bosch. I only added the Bosch logo
A small mont for a small bottle of WD 40
It really holds on good but also easy to remove too!
Drill bit and accessories holder for Bosch PBD40 ( or any other 46mm drill press shafts ). Hollowed bottom for material savings. Clamping area left .2mm larger for you to stick some sort of non-slip tape on ( not necessary ). It consists…
Male Gasmask-Adaptor with Nato RD40x1/7 thread. hose-flange has a diameter of 22,5 mm - the threaded section can rotate freely (fits CPAP-hose's ore corrugated rubber-hose's from some fetish-store's) (fits NOT russian (Warsaw Pact) ore…
Spray can holder, i use it for WD40. Internal diameter 70mm Printer brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 30%
Male Gasmask-Adaptor 90-degree angle with Nato RD40x1/7 thread. hose-flange has a diameter of 22,5 mm - the threaded section can rotate freely (fits CPAP-hose's ore corrugated rubber-hose's from some fetish-store's) (fits NOT russian…
Drum sticks holder 2pcs. No support print. For frame tubes 40-44cm in diameter. I use it with my NUX DM-7X, I'm sure it'll work with DM-7 and DM-8 as well. For other drumsets measure your frame tube diameter first.
I wanted to mount the HD400 from Behringer to the wall. So this is a simple bracket, easy to print wich uses the cover screwholes to mount. The orginal screws are not long enough, so some longer M3s have to be used.
58mm portafilter holder for the cylindrical Turin SD40 single dose coffee grinder. The design is tested to fit Gaggia style 58mm portafilters with a 28mm tall dosing funnel (MiiCoffee Tall dosing funnel shown). It is also designed not to…
Adapter for the Andonstar AD407/AD409 Microscope to attach the stand to a Microphone / Boom Arm. 1/4″ 20 Gang UNC (6,35mm Außendurchmesser 5,35mm Kernlochdurchmesser) 3/8″ 16 Gang UNC (9,52mm Außendurchmesser 8,25mm Kernlochdurchmesser)…
Helpful clip for the 100ml WD40 can. Original with the 200ml + 400ml sizes by Pastelka here: https://www.printables.com
I was missing a screw cover for the mounting screws that hold my LG dishwasher to the cabinet. This part is also 4830ED4001B (AP6231210) replaces 4830ED4001A, 4503016, PS12075919. Printed in PLA with a 0.16mm layer height. The visible…
Female Gasmask-Adaptor with Nato RD40x1/7 thread. hose-flange has a diameter of 22,5 mm - the threaded section can rotate freely (fits CPAP-hose's ore corrugated rubber-hose's from some fetish-store's) (fits NOT russian (Warsaw Pact) ore…
Material: PLA+ Druckereinstellung: Layerhöhe 0,25 mm / Infill 70 % / Support 5% Zusätzliches Material / additional material: Schraube / screw M4 x 35 mm Mutter / nut / DIN934 Gutes Gelingen und über ein Like würde ich mich freuen. Good…
This is a phone holder that I designed for my 2013 Nissan Navara D40 centre console cup holder. It suits the 2010 onward Spain built model that was sold here in Australia. I'd say it would most likely fit the equivalent model R51…
This mount extends the maximum camera distance of the Andonstar AD407/AD409 microscope camera for more overview when soldering. The minimum distance (=maximum magnification) can still (almost) be reached by lowering the arm to the closest…
Description: This is a parametric model that can be adjusted to fit any ring light to any microscope lens. Originally designed for: Microscope: Andonstar AD407 / AD409 Polarized Ring Light: iFixes iL37…
A small spanner for adjusting the spray area on Gardena MD series pop-up sprinklers. Works with: MD40 MD80 MD180 Might also work with (not tested): SD30 SD80
Male Gasmask-Adaptor 90-degree angle with Nato RD40x1/7 thread. hose-flange has a diameter of 22,5 mm - the threaded section can rotate freely (fits CPAP-hose's ore corrugated rubber-hose's from some fetish-store's) (fits NOT russian…
Replacement lever for Bosch PBD40
DC/DC Buck converter, voltage step down enclosure (case) suitable for CR-D4080P
dummy battery for DIY power supply it require also to add a small circuit inside connected to the T terminal
A WD40 bottle with a hidden compartment. You can unscrew the top to open it. I printed it with the mmu3 on my core one. The resolution with the 0,4mm nozzle is not high enough, so the white text is not completely clear, but its readable.
A low-poly replica of a Dremel 3D40 printer. I made it for my aquarium and my betta seems to enjoy it. The STL is scaled as a full-sized printer. You will need to scale it down accordingly. The image is warped because it's photographed…
Hi I created the container for the logic probe when our electronics club was building the logic probe with the CD4001 IC and I did not want to use a pipe for a container. Circuit comes from…
Anelli di supporto cannuccia per Lubrificante WD40 da 200ml. https://amzn.eu/d/evoFrvv
Parts: ESP32C3 OLED from Aliexpress (£2.50 each) https://www.aliexpress.com/item/1005009534750048.html SCD40 (£11 each) https://www.aliexpress.com/item/1005006682069916.html I don't know if my ESP Home code is optimal but it works. So…
I designed that holder in order to place the WD40 in the IKEA enclosure, PETG used for the printing but also PLA it ll work properly.
Simple mount for black and decker li-ion screwdriver with a honeycomb mount part. Printed with default printer settings on Bambu Lab P1S using PLA+ filament. Here is the link of the compatible screwdriver. (Not affiliate)
This is only the part of the spider that is attached to the microphone, printed with petg plastic 0.4 nozzle, 0.4 layer
Made for the smaller cans with ca. 57,5mm I diameter
Very simple rubber feet to prevent scratching the desk surface that the Bosch PBD 40 bench drill stands on. Printed from hardest TPU I had (68D). Print multiple parts at once or slow down print to avoid melting of narrow upper part.…
Printed with PETG, which is considered “food safe”. Regular routine maintenance is required, just as with the original aluminum chute. .1mm layer height Support ‘Touching Buildplate’ only. See photo for recommended printing orientation.…
I needed to extend the Z-range of my Andonstar AD407 Pro, so I designed a 88mm extender. I had some M8x110 screws laying around so I designed the extender for it. The extender will fit and tube that has the internal diameter of 12mm and…
This little "riser" piece can be used to make it so that the AD407 Extender by geit_de can fully rotate.
![[HSW/Multiboard] WD40 Can holder](https://media.printables.com/media/prints/887802/images/6799869_e9efe165-f9a4-40db-8f7e-be92c721f7b6_dde06572-525b-4eb3-908d-d63e5754e247/img_0925.jpeg)
