Liczymy pasujące modele…
A cute dumbbell that can be used as a keychain or necklace. A version without a key ring is also included. Printed with PLA at 60% infill (I wanted it thiiick), without supports. Check also my Kettlebell model ;) they go well together!
Home travel and fitness exercises and fitness dumbbells are very easy to use and can increase enthusiasm for fitness. It can meet your different training needs. Suitable for women or children to lose weight or exercise. Adjustable weight,…
What it is Cylindrical containers for coins, with a lid that screws on. Since seemingly everyone wants you to exercise your money, the 50x coin containers are usable as dumbbells as well. Weights: EUR - full 50x 2 € coin container ≈ 450g…
No supports needed / No se necesitan soportes 5% infill is enough / 5% de relleno es suficiente 3 walls recommended / 3 paredes recomendado 3 top/bottom layers recommended / 3 capas inferiores/superiores recomendado Visit the link below…
For fitness enthusiasts: It was intended for use as a money gift. Simply roll up the banknote and use it as a handle.
You can simply adjust the following parameters in Fusion 360 to easily customize it: Handle diameter Largest weight diameter Total width Thickness of the sides Gap between the largest weight and the floor Support my work For non-Prusa…
Easy printing dumbell nut Ø25mm Perimeter: min. 3 Infill: 30% Layer height: 0.2
This was my quick make of a dumbbell that mimics common brands of adjustable dumbbells. NOTICE: please print horizontal for part strength. Yes you need supports but it will be infinitely stronger that way. Also, be aware of the integrity…
Needed a stand alone dumbell stand that was more material efficient and faster to print than what I could find. The solution was to reimagine something intended for mounting on a separate surface to be stand alone instead. Modified…
Dumbbell Keychain! This easy print is done in about an hour and is the perfect gift for anyone that likes working out! If you enjoy it, leave a like and post a make! Feel free to give me any feedback! I printed this model with supports on…
Print with the same settings as for armor pieces. I used PLA for the weights and Silk PLA for the bars.
Print with supports at .2mm . I used a support enforcer for the middle of the shaft and nowhere else. I did light sanding for the middle just to remove any spurs. If you have an MMU you can do the paint on color and color the letters, if…
Yes, there are already some dumbbell-nuts out there. But they were all missing the possibility to add an additional retaining ring. So i've made this one, which fits a standard D=30mm dumbbell-bar. Also, this model is as close to the…
These are molds for creating a set of dumbbells out of concrete. Weights ranging from 7 to 48 lbs are possible. The larger weights will require a large format printer to print. The process to create a dumbbell is: Print the four parts:…
Printed fine without supports with PLA. Adding o-ring or similar between the weight and the nut will keep it in place without loosening.
A fun Christmas ornament for 2022. Better late than never. I included an optional 2023 version if you want to make one for next year. Thank you so much for stopping by!
Was looking for a dumbbell keychain for my buddy and couldn't find one he liked. Found a dumbbell chopstick holder and made it into a keychain.
I bought some knock-off (not genuine) Bowflex 552 adjustable dumbbells on Craigslist. Later discovered that one of the rotating discs was cracked, so that at certain weight setting, one of the weight plates that should have lifted out was…
Rounded the edges because they were to sharp in my case
These Dumbbell Weight Stands are custom-designed for 3D printing, catering to weights up to ~5KG with a maximum weight diameter of 175mm and a bar diameter of 26mm. Simplify your home gym setup with this space-efficient solution. Download…
To the bar need support, print in place. Spinlock collar a bit tight, must be modified the Y and X axis, for my mk4 need 100,5%!!! Scaled in gcode. Dimension: Bar: length 18cm, diameter 2,5cm Weight plate: diameter 6, 8, 10cm, hole 2,6cm,…
This is a 25-50mm adapter sleeve for converting standard threaded barbells or dumbbells to olympic 50mm size. total length is 190mm, thread depth is 165mm. I also made a separate 115mm spacer to cover the remaining thread on my standard…
Cannot tell a lot about the dumbbell as I created the modell for someone else. But he confirmed that it works.
Print the handle pointing straight up and no supports are needed Print the Hex weight portion on its side as in the stl. Use supports for the hole if need be It is a pretty friction fit but you can add glue if you need to
I created my own model of Gym Hexa Dumbbell Victory V Trophy for everyone, who like gym, dumbbells, victories and trophies :-) This model I created whole by myself. Body of Gym Hexa Dumbbell Victory V Trophy is make to “V” style, to…
Bodybuilder Man's Hand with Dumbbell Wall Decor
Lock Jaw collar and inner collet for Half Inch PVC for use as a dumbbell For the lock jaw you're going to need... M3x20mm bolts x 3 M3 nuts x3 1 pin that is about 3mm dia x 20mm (I used a scrap steel pin wrapped in tape to get a tight…
A little something I designed for my cheapo dumbbell set to allow me to do dumbbell pushups without smashing my face into the floor. Fits the 2.5KG cheapo sand filled plates with a thickness of 40mm and a diameter of 220mm. Contains two…
After I found out that dumbbells are indeed quite heavy and annoying to log around while cleaning I decided I need a movable (and affordable) stand for my 3 pairs of weights, 2 of which are round. So I got this furniture dolly from Aldi…
Dumbbell handle that fits attachment of regular PET bottles (watertight), includes a multiplicator module that enables an increase in the number of bottles, and thus increase in weight. Remix of keizi666's PET bottle cap design (…
My Misses wanted to have her dumbbells on the wall and I thought a protective plate might be a good idea to protect her fingernails and the wall at the same time. We ended up mounting the hooks without the plates, because my Misses…
Printed in PETG with 7% infill (except the crossbars that are printed with 20% to increase stability). Supports are only required for the parts “middle” and “top”. The side parts must be printed 2 times each, the crossbar 3 times. For…
I bought a pair of (broken) adjustable dumbells off Craigslist. These are biggies that go up to 32 kg (70 lbs) each. One was in very bad shape, so I had to fix a bunch of stuff. Including straightening out a bent core rod. They appear to…
Dumbbells holder, it can handle up to 4 2kg dumbbells. ABS or PETG 0.2mm 40% infill 3 perimeters
dumbbells, fitness equipment The print was made in PLA. The dumbbells has a total weight of 4 kg., I used lead shot, I recommend you to collect them in a bag or cloth bag. additional material - 1 aluminum tube 25 cm in length and 26 mm in…
Remix of Peterthinks weight adapter to instead fit a dumbbell instead of a weight bar. Worked great for my CAP Olympic 2-Inch Weight plate. As he said, don't stand the bar on end with weights on it. If the weights shear off the round…
I suddenly got a parrot, so I thought about a toy I could play with. It has the shape of a hollow dumbbell-shaped rolling barrel and has a rattle inside that produces sound. The caps on both sides can be assembled by snapping them…
Fillable Adjustable Dumbbell (DIY / 3D Printable) This is a fillable, adjustable dumbbell designed for home use and easy 3D printing. Instead of fixed weights, the dumbbell can be filled with common materials like sand, rice, lentils, or…
Wrench for tightening / loosening star locks for your dumbbells / barbells. I usually can't get them tight enough and they come loose after a few reps. With this wrench you can tighten them much better. See Picture 3 for Dimensions. I…
The matte black, monochrome finish highlights muscular anatomy and gives the sculpture a bold, modern look. Perfect for gym décor, fitness studios, or minimalist interiors.
This is a simple model designed to prevent dumbbell weights from moving or rolling when placed on a surface. The dumbbells I use are the 10kg set sold by York Fitness in the UK. The holder works for any configuration of the weights. The…
The original handles took too much getting used to. Modeled these replacement handles in 30mm grip and knurled. Will add 25, 35 and 40 soon.
Keychain with two dumbbells and "Gym" lettering. Dimensions: 50x30mm. The hole is 5mm in diameter. The lettering is recessed by 1.5mm. Can of course be scaled accordingly. Printed with PLA.
threaded rod 12mm (d) / single thread rod diameter 2.5 cm
I designed this gadget to make to Quest 2 controllers a bit heavier. With the extra weight games like minigolf or fighting with a sword feel more realistic. Also it may increase the fitness aspect. I chose wide washers from amazon, outer…
Dumbell Stand (Single) Used for dampening the weight so it doesn't damage floors while reducing noise and also holding it in place which reduces rolling. This version is design for a CAP Barbell set. Plates are 6''. Radius of groove is…
I needed some organization for my dumbbells and some extra weight I had. I sketched up this rack which fits two dumbbells and some extra weights on top. Everything was printed in PLA with 4 perimeters and 25% infill. I am using that one…
How to customize this model: Download the *.f3d-file Open the file in Fusion 360 Click on “Modify” → “Change Parameters” Enter the right parameters for your weight plates under “User Parameters” You can then export the components and…
Prusament PETG 0.4 mm Nozzle 0.2 mm Layer 6 Perimeter 25% Infill
This ring allows you to mount weight plates with an inner diameter of 30mm onto a 25mm handle. If you need anything, feel free to reach out! Questions/Suggestions/Criticism is highly appreciated…
Fill this with sand or water. Sand must be dry. Use the funnel for filling. Hammer the clog gently when finished.
Simple to print. Protects the floor and unwanted rolling off of your weights. Feel free to use STEP file to modify for your own sets.
Tibialis trainer extention for a dumbbell! This allows you to train train your tibialis, the muscle at the front of your legs, and strengthen them. Great for preventing shin splints and general athleticism. It is a single piece, built for…
I created this simple dumbbell that may be 3D printed because I had unused weights and wanted to put them to use, without buying another set of dumbbells. This also has the advantage of being lightweight, when compared to the metallic…
For secondary pair(s) of dumbbells for your kids or if you need a light setup in addition to main one, for wrists training or additional weight while running or jumping, etc. I suppose usually they should take not more than 1 disk on each…
Very simple boot to slide onto the end of a hexagonal dumbbell to protect it and the surface you set it down on. Bare-metal dumbbells tend to be a lot cheaper than the ones that have a rubber coating on them. I have tried applying…
PowerBlock Elite adjustable dumbbells have 2.5 lb cylindrical bars that can be removed/added to further adjust the dumbbell weight. If you don't have the PowerBlock stand and instead just have your set on the ground, this print will give…
You are probably a Lego fan if YOU tapped this model. This model is an accessory for Lego minifigures across the world allowing them the freedom to work out and get jacked. If you made a Lego model gym, it would be perfect for it! Please…
Modeled up an exact replica of a dumbbell saddle for a friend. Should be to the exact spec of the original. Make sure to print with lots of walls and top and bottom layers and a good amount of infill of you are putting heavy weights on it.
Adapter for Barbell Plates (52.5mm ID) to Dumbell Grip (25mm OD). Barbell plate thickness varies, there are models for 10lb (27.5mm thick) and 5lb (20.4mm thick). Threads are M40x2 Standard 0.20mm P1P Settings (Adaptive Cubic Infill)…
Attach to a suitable weight to use in static strength exercises to develop better muscles. Especially useful for Camp Perry style “airsofting”. You'll definitely find this familiar if you are old school competitive. Greater strength means…
This is a remix of the keychain https://www.printables.com/model/615893-dumbbell-keychain by Erika Heidi (@erikaheidi)
Dumbbell keychain to share with your gymbro/symsis I used 2x 6x3mm magnets I found on amazon There are two files if you want it multicolor. Make sure to align everything fine while slicing it and include a pause at height before the…
Small dumbbell earrings. holes are sized for a 16 gauge wire insert Print Settings Printer Brand: Creality Printer: Ender 3 **Rafts:** No Supports: No **Resolution:** 200 Infill: 38 **Filament:** PolyMaker PETG Category: 3D Printing
Easy ruler for reading how much weight is on the Eisenlink Adjustable Dumbbell (https://www.amazon.co.uk/dp/B0BZHHCSFD) The left side of the ruler measures when only the 2kg plates, are used. Read the right hand side when 2 x 1kg plates…
Width of the stand is 12 cm. Diameter for the bar is 1.3 cm. I've printed mine with Polyterra PLA, which isn't very strong. Still holds my 12.5 kg dumbbell easily. I would recommend some rubber feet.
Dropped these dumbbells and a disk broke so I printed a replacement! Print 1 disk or swap them all. I printed them at 35% infill, 4 wall, and with supports.
A small charm with a loop for mounting. Best printed using resin in batches. There is usually a little spoilage in removal when you print this small. Use 1 or maybe 2 sprues per piece. Disclaimer: Please refer to the manufacturer of your…
I've created a Dumbbell set for the Dummy 13 / Mini 13 figures using OpenSCAD. The weights and handles are printed separately and pressed fit together to provide: 1) easier installation, 2) multicolor support. If you generated the STL's…
This stand supports the dumbbell for easier loading with plates. It is designed for dumbbells with a grip-diameter of up to 30 mm, a grip-length of at least 125 mm and plates of up to 5 kg. Tested until now with 25 kg with the following…
Hello Everyone! Every year I try and make my gym-toting family member a fun gym-themed ornament. Last year it was the barbell weight. This year is the Christmas Dumbbell!!!! This ornament comes in three pieces. Each side and the handle…
Dumbbell shaped can opener. Four printed pieces, one m3x30mm bolt. Top piece is attached with superglue. Recommended print parameters: Minimum filament: PETG Recommended filament: PETG Layer height: 0.2mm Perimeters: 3 Bottom/top layers:…
It need to be printed on the high surface area of the nut, at 10 mm/s for the first layer, and the other layers idc, u could use the speed u want. I used a Filament Dryer for my filament so it affected a little the tolerances in the…
For 1" / 25cm thread handles. Ring should be a rubbery material like TPU.
Printed in both ABS and PETG without supports at 0.3 layer height. Regarding threads, I suggest printing the v2 since it's more resistant and fast to print. Cut the long thread before slicing at the desired thread height. For example, I…
I have tried several variants of nuts which looked promising, but none of them rotated freely and lacked the shape. So I recreated the original nut. Note: the diameter of shaft is 25mm with pitch 6.4mm Layer: 0.2mm Walls: 3 Supports: yes…
Recommended material: PLA, PETG, or ABS (PLA is ideal for maintaining text sharpness). Nozzle: 0.4 mm. Infill: 15%–20% (Giroid or Cubic pattern). Support structures: No supports required! The design is geometrically optimized with 45°…
No special printing requirements. I have made these for myself from PETG. Tested succesfully with InSportLine bars.
A compact stand for BESTIF Dumbells that hold 2.5kg plates perfectly + adapter to hold 1kg plates. Included a version with embedded 12 x 4 x 1.5 mm magnets (printer pauses for you to place magnets inside the print) for easier use.…
**English:** I created this dumbbell-to-kettlebell adapter. It also helps when using the dumbbell for sit-ups and squats. There's an earlier, longer version, but I don’t like it as much. I’ve also made a version for two materials: TPU and…
Introducing the Dumbbell Forearm Grip—the unsung hero of your home gym setup. This ingenious attachment seamlessly screws onto one end of a screw-type dumbbell, offering a focused workout for those oft-neglected forearm muscles. No longer…
COVID-19 stealing your gains? Make simple dumbbells from a couple of regular plastic bottles and some dirt/sand/water with this connector. There idea of the chamfer in the middle is to create a tiny weak spot, so should the connector…
Made this to keep the weights off the ground on my veranda/patio. Printed these in PLA with only 2 perimeters and minimal fill and they have held up for a year or so, with some minor damage from abuse. I would recommend printing with more…
Bring energy and strength to your modern scenes with this Fitness Man with Dumbbell 3D printable character model. Featuring a muscular athletic build, casual workout attire, hand-held dumbbell, and towel over the shoulder, this figure…
The Technogym Group Cycle has no bike weights holder, so i needed to design one. The holder has two mounting points. Except the Holder you will need a 15 mm diameter 6 wood screw or M6 screw I recommend printing with 4 Perimeters and…
Weight/Dumbbell Stand - No support needed
A leg saver 3D printed endcap for good old castiron dumbbell/plate systems you might have at home which uses existing metal nuts for safety and magnets to attach the leg saver to the outermost plates tightly. If you printed it/created it…
This is a dumbbell meant to be used with a Theraband/resistance tube that you can buy like this:…
I created my own model of Hex Dumbbell for cosplay / costume purposes :-) This model I created whole by myself and was intended mainly for cosplay / costume purposes. I hope You like it :-D Print settings Printer Brand: Prusa Printers: i3…
Important: These are sized to fit one inch adjustable dumbbell bars with removable rubber grips. They will not work with all dumbbells. What are fat grips? Fat grips are replacement grips for adjustable dumbbells. Fat grips help you build…
To be honest. I'm not 100% happy with this yet. Since the plastic is much lighter than the weights it moves when pulling the weights out and putting them back in. I'm thinking about making one that is either wall mounted or can be screwed…
I had to print something quick for a gift on the spur of the moment / es musste spontan etwas schnelles für ein Geschenk gedruckt werden the font is customizable in the original file / die Schrift ist in der Originaldatei anpassbar
Two versions. Normal and extended for people using larger diameter weights. Turns your 1 inch dumbbell bars into push up bars. Also keeps your weights from rolling around which is nice. Mix up your workout. Category: Sport & Outdoors
If you need elbows rehab or you want do train your arms to be a better pistol shooter or else... You can convert a typical dumbbell in to a clubbell.
![Dumbbell Nut [with retaining ring]](https://media.printables.com/media/prints/629397/images/4986889_71e11b9f-690d-45cb-a5dc-933b6a2a53ef_ec463bf9-fd76-4570-b941-a4c4ae8022a5/img_20231028_164652.jpg)
