Liczymy pasujące modele…
28/8/23 Added step file for battery holder to aid with remixes 2 versions, a single battery and a triple battery version. Prints vertically, no supports Important note on scaling As the fit of the battery is so precise I would advise…
Universal holder for any cordless drills and tools. I used it mainly for Makita, but other power tools should fit as well of course. The following Makita tools have been tested so far in the 40mm version: Makita DTD171 Makita DDF484…
I would like to introduce to you the 5th version of my wind-up boat. After the 4th version i got a lot of feedack on Facebook, which I have implemented as well as possible. As you can see there is a much larger wind-up weel. The boat can…
These are tool mounts for DeWalt cordless tools. They can be screwed into the underside of a shelf and fit to the battery female end of the tool. Print standing up. I use 3 walls, 20% infill, and no supports.
NEW VERSION 2 : link After releasing two print-in-place card wallets, I decided to take a different approach for my next design—this time, not print-in-place. I revisited the drawing board and developed a brand-new design with an…
Adapter folded from two parts to limit the use of supports DeWalt battery adapter You will need: 5x M3 - 15mm screws 2x male connectors and wires
A Dewalt tool holder that should work with most Dewalt tools that use an XR battery. This holder replaces the battery in the tool so that it can be mounted to a wall for easy and convenient storage. I currently use this to mount my 4"…
Universal Cordless Impact Driver/Drill Holder A universal cordless Impact Driver/Drill Holder meant to organize your workbench as well as make it more ergonomic and easier to use. Front extrusion allows for it do double as a bottle…
This DeWalt 20V battery holder mounts to the wall and positions the batteries horizontally at a slightly upward angle. This allows for the batteries to be stored closer together than the traditional vertical holders. Other battery…
This cable mount can be screwed or glued in place and is available for 3mm - 9mm thick cables.
A holder for DeWalt devices attached to the battery with an additional lever to prevent spontaneous falling out
Simplified version of the Dewalt Battery Holder by maglub. No need for the battery to lock when hanging the battery on the wall. Print Settings Printer: C3Dt/xcy Rafts: No Supports: No Resolution: 0.3 Infill: 20% Filament: GreenGate PETG…
Screwable headset holder. Can be used on desk up to 35mm. Headset width must not exceed 38mm.
DeWalt Power Tool Battery Holder This holder is designed to hold DeWalt 20v Batteries. Designed based on a 3D scan of the DeWalt Battery and refined for a snug fit. Print instructions HARDWARE • Screws: x2 wood self tapping countersunk…
Gridfinity is the popular Modular Storage System invented by Zack Freedman. This is a remix of his baseplate . There are already many great remixes of this baseplate out there (e.g. Gridfinity Screw Together baseplate ), but I could not…
I wanted a zero clearance insert for my DeWalt DWE7485 jobsite saw and printed another I found online but it didn't fit my saw very well so I set out and whipped this one up. The insert fit well enough and was fairly straight forward to…
I used .4 Nozzle with Bambu Lab PLA (Yellow). 15% Infill and support. For best result print the part with the flat back face oriented down. If you like this design and would like to support my work, please share and consider donating to…
A simple cable organizer when you really have to many cables to manage. The design is similar to what you can find in computer room (usually it is several meters in length and you cut it to size, but here we are limited to the print bed…
Following the unexpectedly successful launch of the SlideWallet V1 and receiving a lot of feedback, I set out to create Version 2. This new version addresses as many issues as possible while incorporating a highly requested feature: a…
I wanted something simple, rugged and compact to EDC one pill of Ibuprofen, without its packaging being damaged by other tools I'm carrying in the same pocket. It was my first attempt at designing something with a thread in FreeCAD and it…
This 1/4" Hex bit holder is attached to the opposite side of the drill or impact driver than the belt clip. This device fits a Dewalt DCF887 impact driver and DCD996 hammer drill. I'm sure it would fit most Dewalt 20v MAX drills/impact…
More updated designs on malerworld since i’ve moved to bambu printers : https://makerworld.com/models/661522?appSharePlatform=copy These nested cups are designed to fit in both the small and large bins from the Dewalt TSTAK Shallow…
Alternative sawdust extraction adapter for the DeWalt DCW600, DCW604, D26200, DWP611 milling machine. This adapter has the huge advantage that it does not have to be screwed onto the milling machine, but just clicks. In addition, it has a…
John Stewarts Ring from the up coming Green Lanterns HBO series. Not 100% accurate as only based on one shot from the teaser trailer.
Ich war auf der Suche nach einem modernen minimalistischem Papiertuch Halter für unsere neue Küche und habe nichts 100% passendes gefunden. Daher habe ich diesen Halter selber designed. Er passt für klassische Zewa Rollen mit einer Länge…
I've been using the DeWalt DCBL722 20V leaf blower now for better part of a year. I was always disappointed it only ever came with the one nozzle on the end of the blower called a “concentrator” but it's really more of a diffuser. I was…
DeWalt AirLock compatible twist-lock dust collector fitting I like DeWalt tools well enough and own a bunch, but like every other tool vendor their approach to dust collector connections is psychotic. I'm not at all convinced that any two…
40mm high paint cones (or tetrahedron to be precise !) that you can stack up and screw on your work surface if needed. The corner are rounded to not get stuck on the part you want to paint. If you don't need to screw them on the work…
Aufbewahrungsbox Küchen für Maggi, Knorr oder ähnliche Tüten. Die Box hat standardmäßig eine Breite von 17cm. Kann aber einfach mit dem Slicer deiner Wahl herunterskaliert werden auf die gewünschte Breite. :) 13cm breite für große Tüten…
After coming across afri.mandjelikian great design for the Dewalt/Stanley/Craftsman TSTAK FATMAX Versastack Organizer Nested Cups , I needed one for storing various sized M3 Button Head Socket Bolts in. I decided it would be more…
Carry 6 DEWALT 20v batteries to and from the job site with this sturdy carrier. Printed in Creality PETG with 10% infill and 3 walls. Just a few supports suggested for the handle.
The Cloud Gateway Max gets hot! Do not print in PLA!
The make is made of 6 panels, 3 wide by 2 tall for a final product of 24 inches wide by 16 inches tall This uses an improved panel system as compared to my previous background ( https://www.thingiverse.com/thing:3509102 ). A double sided…
How to use the jig: 1) set the slider to the desired thickness 2) set it slightly before the blade 3) move the parallel guide until the wood touches the bearing, then fix it in position 4) perform the cut 5) repeat step 3) and 4)…
A simple, modern-looking planter. I printed mine with a 0.4 mm layer height, resulting in single-wall edges. It was a little experiment that took about 3.5 hours to print. I’m sure modern printers can handle it much faster. Please note:…
This is a zero clearance insert for Dewalt miter saws. I modeled it from the insert on my own saw wich is a DW716 (12inch, dual bevel, NON sliding) from what I can tell from the replacement inserts on amazon, this will fit models:…
A set of saw blade holders for all common electrical jigsaws. The lids clip on and will stay on even if you turn the holder upside down and shake hard. Your saws won't fall out even if you toss your toolbox around. Chamfers make inserting…
Designed based on the handle of a Dewalt DCF787. I cannot confirm whether this will fit other Dewalt tools. Features Positive retention on the bits so they do not fall out Produces a satisfying snap when bits are inserted into the holder…
A simple battery cradle with a color change to pop out the brand name. Can be standing on your bench or mounted on the wall. The infill is strategically modified to withstand use and mounting. Open hex pattern allows you to press and see…
The only thing worse that the subscription model, are overpriced accessories that should have been included! I made this for myself, as I will only use it with a 2280. So, if you're are only going to use a 2280 too, have at it. Includes a…
Less than 10 percent of people who download an item click the “like” button. Be the 10 percent. Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee . Here's a minimalist wall mount…
I used 25% infill with the print standing up. PETG recommended. 4 hour print time. No brim needed.
This is a remix of "1/4" hex bit holder for a DeWalt drill" by Lowell Alleman. I wanted to be able to hold more than one hex bit on the side of my impact driver at a time, so I made a double barrel bit holder. I used the same M3x10 screw…
I know there are a number of holders available for the DeWalt batteries but I decided to design/print my own after seeing complaints of “too tight” along with not seeing options for both the 12V and 20V battery sizes, not to mention the…
The original model couldn't be used on my desk because it is much thicker then 35mm, so I remixed it. You'll need screw.stl, plate.stl and nut.stl files from the original model (…
Do pobrania Listwy Elektroinstalacyjne, do maskowania przewodów i kabli, listwy dodaję o długości 250mm i w następujących rozmiarach wewnętrznych: 1 . Wysokość 10mm i szerokości ( 15mm, 20mm, 25mm, 30mm, 40mm i 50mm) 2 . Wysokość 15mm i…
I found a well designed jig on the internet but because I already spent too much money on jigs and tools I built one myself. For your convenience I've included all Fusion 360 files so you can make changes to the design. To make…
Für die Werkstatt habe ich einen Küchenrollenhalter kreiiert er wird mit zwei Spax in eine OSB Wand geschraubt. 20230711 “Möbelschrauben” feiner justierbar 20230723 Ikea Skadis hinzu 20230725 auch ohne Wabenmuster 20230729 Verschraubung…
This is a basic wall mount for a DeWalt jigsaw (DCS331). Its designed to be quite snug so that the tool doesn't slid out if you want to mount it under a shelf. I printed it with 6 perimeters and %40 infill as I wasn't sure how strong it…
Bitholder for DeWalt cordless drills and impact drivers. At least fits DCD796. Screw to secure is standard dewalt screw (M3 10mm). Printed in PETG, 40% grid infill with auto support.
Pretty self explanatory. I was getting tired of carrying around a small box full of drill & driver bits, so I decided to make an accessory that clips easily onto my DeWalt DCD999 drill/driver. Presumably it will clip onto some of DeWalt's…
I made this mating connector for a Dewalt 20V battery pack so I could use it in a battery-powered project. For printability I split it into two halves and glued them together. I used ¼" spade terminals as the contacts, which can be glued…
This DeWalt battery mount uses a single screw to mount to any of your desired surfaces! It prints without support material, and is symmetrical so you can install it in either direction. If you want to support me or get a commercial…
This is a remix of two designs to get the best of both for my DeWalt Table saw with metric nuts and bolts. Following Designs are used: Sliding Block: www.thingiverse.com/thing:3973092 The block was dapted to fit for the DeWalt 7491 & 7492…
Inspired by https://www.printables.com/model/519833-rugged-makita-battery-holder/remixes
The step files is meant to be used as an asset in CAD software. But as it has a very simple geometry it can be printed in Vase mode. I added an optimized version for the vertical cover, cut in half and added an angle for the overhang on…
Lets hang your DeWALT / Makita drill gun under your shelf! Designed for DeWALT DCD791, but it works also with Makita 6270D and probably with other similar models from different brands. Be sure to check also my other DeWalt hanger holders:…
I didn't have room on mine to mount it up and down so I designed this sideways mount. It does not need any supports if printed in the orientation I have pictured.
Just squeeze router on router base. Print with less support possible!
DeWalt 18V XR Battery (Transport) Cover/ Holder (With a hole for a hanging loop). Print settings: 🖨⚙ Material: PLA Layer height: 0.2 Infill: 25% Support: NO Print speed: 30mm/s ⚠ (Notes: The cover is printed in portrait. Also works with…
Perfect fit for SKÅDIS mount for Ubiquiti Unifi Cloud Gateway Ultra. Does not block any I/O. Requires 2x Skadis T-Clip System - Low Profile Flush Mount Clips No support needed Printed with PLA with default setting
A minimalist 3D-printed photo holder shaped like a flowing Christmas tree silhouette. Its smooth wave design elegantly supports your favorite memories, blending festive charm with modern décor. Perfect for displaying Polaroids or small…
PLA is fine for indoor storage.
Update 5 : Es sind 2 Versionen für den 25W Charger (+Silikoncase) online da dieser kleiner ist. Eins mit und ohne AppleWatch Charger. Finden sich im Ordner “ 25W MagSafe ” Update 4 : Eine Version für das iPhone 14 Pro, 15 Pro und 16 Pro…
I redesigned this throat plate eliminating the screw holes and lock (lock is not necessary to have). I have fine tuned the bottom feet to be the exact height to level the plate with the table saw top (you can slightly sand these feet if a…
UPDATED: A simple cable management raceway / comb to help keep wiring tidy. Designed in OnShape, based on a common wire management product. Top snaps or slides on to the comb / bottom piece. They can be easily cut to length as needed. The…
Dewalt battery holder or adapter. You could use this just as a mountable holder or if you insert a .7 inch strip of .032 brass you can connect to the battery. A small compartment is made for a fuse, reverse voltage protection or what you…
Simple attachment for the Dewalt 735 to get a 4"/100mm hose up and out of the way of boards exiting the rear of the planer! Simply push in the button on the stock port, rotate and remove the original stock black port. Install this…
Adapter to connect FESTOOL™ CLEANTEC™ D27 Dust Extractor to DeWalt™ Air-Lock™ tools This adapter is designed to allow a FESTOOL dust collector with a D27 hose fitting to connect easily to DeWalt tools featuring the "AirLock" style dust…
This is only my third 3D print. I made the adjustments using TinkerCAD. I used PETG filament and an Anycubic Kobra S1 printer.
Heyhoo Here I have a new Container for you :) Perfect to store away some dry stuff like Coffee or other things! In addition to the obvious, that the container is as well sealed as possible, I also took great care to ensure that it is very…
Horizontal Magsafe and AppleWatch Stand This is a combined MagSafe iPhone and AppleWatch charging Stand that holds the phone horizontally to take advantage of the new StandBy mode in iOS 17. All cable cutouts fit both USB-A and USB-C…
The lift fits on a DeWalt laser DCE089D1G. The laser beam can reach a height of 32 cm from the ground. The lift itself c
This model is inspired by the design by USSA Design (watch their video here: https://www.youtube.com/watch?v=2JYTYOJt_m4). I made my own so it worked with my Dewalt DCW604 router. You will need to print 4x support screw 4x support screw…
Adapter allowing DeWalt's DCW210B sander (or any other tool compatible with the DWV9000 adapter) to a Festool 27mm dust extractor hose, with or without the twist-lock mechanisms each connector allows. Updates: 2025-09-21 Increase…
DeWalt battery holder that mounts to a 1/4" pegboard and takes two standard size 20V (AKA 18V in some parts of the world, but using misleading marketing is the norm in North America) DeWalt batteries. I wanted a sideways mount so that I…
Many wall mounted brackets and holders already exist for DeWalt's iconic 20 volt batteries but after having looked at many designs I found them all lacking in various ways so I decided to make my own. Its main virtue is that it uses under…
So i wanted to make various ways to mount Dewalt Battery Chargers (DCB112/DCB115 and the DCB118) The DCB112 and DCB115 screws are 114.3mm apart, and the DCB118 is 133.4mm First option, is a simple 2mm thick alignment jig. you can print…
This money bank is big enough to contain coins and bank notes when you are saving for rainy days. The Main Body is a single piece so a color change is needed if you want to have the base in a different color. The Top part screws onto the…
Cordless tool battery adapter. Dewalt Battery to Makita skin tools Extra hardware spade connectors wire 9mm female terminal fuse terminal M3 x10mm bolt & Hex nut Prep spade connectors like this, flatten out the shoulders if you can…
I ended up slightly modifying the slots on the featherboard, as well as designing new knobs and slides, all of which fit common-to-the-US 1/4-20 UNC hardware. Use lock nuts in the knobs and standard 2-inch-long hex bolts in the slides.…
A simple wedge to help mitigate the slight tipping effect on DeWalt Tough System 2.0 toolboxes when you stack them together. If anyone knows who makes a yellow that best matched the DeWalt yellow please let me know ☺
Simple wall mount for the Unifi Gateway Lite (UXG Lite). You can face the ports either up or down, but not sideways. “-wide” has a wide hole pattern that has the same width as the old USG Gateway wall mount, making this wall mount a drop…
I remixed Ashf144's file on Thingiverse to nearly eliminate the need for supports and improve the overall look (in my opinion). I also added a bevel where the battery clip goes to help it slide into place better and more easily. The only…
EXPAND YOUR CORDLESS WORKSHOP TOOLKIT! Check out our other tools: - 100W USB-C Power Bank Adapter — Fast-charge laptops, phones, & gear on the go. - Portable Soldering Station — Cordless soldering station for field repairs & benchtop…
These are simple 20x20 cable raceways to clean up any kind of wiring project. They have holes for M3 screws to mount to to extrusions or you can use VHB tape to mount to a flat surface. I have .stls for 90mm, 110mm, 130mm, and 150mm. I've…
A 90° degree transition from the Dewalt DW735 dust collection port to 4". Here I'm using a Rockler quick connect but it'll also work fine with a 4" flex hose and it may work with various other fittings but I haven't verified this. The…
Dewalt Tool and Battery Holders
Dies ist ein Remix vom AMS Stack von LusBueb. Ich habe die Öffnungen verengt, somit wackeln die Steckverbindungen weniger. Ich habe auch die Abstände zur AMS verengt für eine stabilere Verbindung. Zusätzlich habe ich auf die die Lösung…
I printed upright without supports using PLA+ 3 walls, 3 top and bottom layers with 20% infill.
This sturdy wall mount is designed specifically for DeWalt drills, providing a reliable and space-saving storage solution. Designed for durability, it securely holds your drills while ensuring they are easily accessible whenever needed.…
An adapter between a DeWalt orbital sander and a shop-vac hose. Specifically designed to work with a DWE6421. There are two versions. One for a Shop-Vac hose that is ~1 1/8" OD, and one for a DeWalt hose that is ~1 7/8" diameter. F3D…
My Dewalt Stick Vacuum is quickly becoming my favorite tool. SUPER cheap compared to a Dyson. I already have several Dewalt 20v batteries, and it's right at home in the garage for a quick tidy. Only problem was: there was no wall mount…
This is an adapter to attach a vacuum to Dewalt orbital sanders. It isn't mounted using Dewalt's system instead it's just a friction fit. I've designed it for a couple different sizes of vacuum hoses. you will need to measure your…
Printed adapters for interfacing with the top of Dewalt toughsystem 2.0 boxes. Worksurface was cnc routed from ½" MDF by Sendcutsend.com (approximately $35 each at the time). Used these threaded inserts from the bottom side to attach…
While you can insert coins through the letter slot, larger banknotes can easily pass through the top functional flip-down tray. The whole mailbox can be printed and put together within a weekend or less. Although this model necessitates…
These are a remix/inspired by the DeWalt Tough System boxes on here. These are for the Deep Pro Organizer model #DWST14825 although they may work on other models. I've included replacement models for the factory full and half size cups…
Huge thank you to @kukynas for adapting the step files to the K1 Max Dimensions. As it has a very simple geometry it can be printed in Vase mode. I added an optimized version for the vertical cover, cut in half and added an angle for the…
Allgemeines 70mm runde Aufbewahrungsdose, welche sich schnell und einfach mit 0,25mm Schichthöhe drucken lässt. Eine Version mit einem Trennsteg und eine andere mit 2 Trennstegen im Inneren. Optional kann z.B. eine Beschriftung angebracht…
