Liczymy pasujące modele…
Introduction My primary school child needed something for the class Valentine exchange. We didn't want to go with candy or the typical ‘supermarket’ boxed cards. My child is constantly searching for a bookmark, so I decided to create a…
Wydruk około 0,17 €–0,20 € nettoWstępna wycena jednego wariantu
And again a simple, customizable OpenSCAD design. This time it's a two component stamp, a generic handle part and an interchangeable rubber part; no gluing necessary, simply print one or more texts and switch them around as you like.…
Made this Barrelend/Holder for scientific purpose! I will test different kinds of barrels for the rampage! Just in case someone needs this... Needs 2 spare screws (the ones from the case) or just tap M3 into it if you like. Edit: Seems a…
Often I found out that my choice of infill style and infill percentage was not best. Now I can print my infill samples (30x30x5mm), just leave the top layer = 0. I added a lot of grid patterns: 1 only, 2x1 grid, 3x4 grid, 4x4 grid and 4x5…
Printed in PLA with gyroid facing downwards on print bed, no supports required.
Layer height : 0.2mm Supports: Yes I am using esun PLA+ and it prints well
This is a heat exchanger for 6in ducting. As an example, I used it to temper incoming makeup air for a basement kitchen hood's exhaust. I printed using carbon fiber reinforced PLA. I don't have the equipment or knowledge to test the…
I made this for our bearded dragon enclosure. We live in a cold climate so circulating fresh air all the time can make it difficult to maintain constant temps inside the enclosure. We already order these activated charcoal filters for our…
I made the bottom and sides solid instead of vented. Used the original lid
Introduction My primary school child needed something for the class Valentine exchange. We didn't want to go with candy or the typical ‘supermarket’ boxed cards. My child is constantly searching for a bookmark, so I decided to create a…
Wydruk około 0,17 €–0,20 € nettoWstępna wycena jednego wariantu
Printed in PLA with gyroid facing downwards on print bed, no supports required.
The game file for the exchange market sign, a component in Worldbuilders, the new 3D printed board game. All information about colors, quantity and usage is listed in the attached pdf file.
This is a desiccant case for the SH02. It can be used with silica gel larger than 1.5mm in diameter. NOTE: Please print it in 0.15mm layer height without supports. Added 1.0mm gap models too(January 20th , 2025)
Most 3d printing filament dryers have a fundamental flaw: they heat the filament and pass air over it, but they are a closed system with no venting, so moisture escapes only by accident. With single piece dryers, fixing this is intrusive…
A barebones heat exchanger core for air cooling and heating projects. Default size is 186x186x180mm. I haven't printed the bare exchanger, but successfully printed the pattern using carbon fiber filament inside 6in cylindrical ducting.…
This is a heat exchanger for 6in ducting. As an example, I used it to temper incoming makeup air for a basement kitchen hood's exhaust. I printed using carbon fiber reinforced PLA. I don't have the equipment or knowledge to test the…
Liquid heat exchanger I need to cool down a bunch of instruments and our laboratory has a primary cooling water circuit. Yet it is dirty and the pressure difference between the supply and return line is too low. In order to decouple my…
This is used to add passive air exchange for use with mycology grow boxes. Standard cotton rounds are used for inserts, and they can be replaced safely and effectively, even when the cotton rounds become wet. Ideally, mushrooms require…
you can find here the detailed description. this version requires more intervention, but is fully integrated and actively exchanges the moist air with the ambient air. I remixed “ Sunlu S2 base with ventilation ” to have an seperate and…
We wanted to give an award for best white elephant gift at our white elephant gift exchange this year. Just used a little super glue to attach the elephant to the base.
It is a smal part to fit in for design reasons. Print all parts in the given orientation (or as you see fit) No support needed. The big gap in the Base part works with a bridge. If you add a manual color change to the Radiator part, one…
This is a GraviTrax tile designed to push out a pre-placed ball using the momentum of an incoming ball. The tile has a 10mm slope, and the incoming ball enters from the higher end. Apparently, the speed of the incoming ball is important.…
My teacher wife wanted to have a memory game for the kids which she can reuse with customizable paper prints. Thats what came out. The paper square must be a maximum of 4.8 x 4.8 cm. Maybe a bit smaller due to tolerances. On my MK4 it…
I need more height to closer match my filament sensor and gantry as it raised during the print. The 5% exchanger vent is to help humidity escape w/o great loss of heat (per original designer).
structure : The button consists of two parts: the base that is sewn onto the dress and the cover that is screwed onto the base. Attention : screw the cover to the base only after sewing the base to the dress, otherwise you risk not to be…
EN: The stamp is designed so that the stamp plate on the stamp foot can be exchanged. This means that different motifs can be stamped with the same stamp handle. (PLA, Prusament mystic brown). The recesses visible from the front and side…
EN: For Stamphandle, box and instructions see: Motifs : smiley-2c smiley-2b smiley-2a flat-ist-borin Stamphandle: Stamphandle Organizer-box: Box Material : FLEX, (TPU) 85A Layers : 0.2mm Infill : 100% Supports : no…
EN: For Stamphandle, instructions and other models see: Motifs : smiley-2c smiley-2b smiley-1 flat-ist-borin Stamphandle: Stamphandle Organizer-box: Box Material : FLEX, (TPU) 85A Layers : 0.2mm Infill : 100% Supports : no…
EN: For Stamphandle, Box and instructions see: Motifs : smiley-2b smiley-2a smiley-1 flat-ist-borin Stamphandle: Stamphandle Box : Box Material : FLEX, (TPU) 85A Layers : 0.2mm Infill : 100% Supports : no…
EN: For Stamphandle, box and instructions see: Motifs : smiley-2c smiley-2a smiley-1 flat-ist-borin Stamphandle: Stamphandle Box : Box Material : FLEX, (TPU) 85A Layers : 0.2mm Infill : 100% Supports : no…
EN: Box for 10 different stamp motifs. Material : Stamp handle: PLA, PETG Layers : Stamp handle: 0.3mm, 0.2mm as desired Supports : no Motifs : smiley-2c smiley-2b smiley-2a smiley-1 flat-ist-borin Stamphandle: Stamphandle…
It's a small plug to fill with polyfill and insert into the mushroom bags for fruiting. (Not for colonization.) I know most people use bags with built-in filters or pierce their bags with a needle, and this plug crosses the line into…
I created this frame for my Open Print Exchange Prints. They are 7x7 cm. The Open Press Project had an own Frame but I can't find it any more to link it. By the time I created the frame (Oct-23) there were not available frames. Open Print…
I wasn't quite sure about the naming (feedback welcome) but this is the current naming scheme: Nozzle Sizes: 0.25, 0.4, 0.5, 0.6, 0.8, 1.0 Types: B -Brass HB - High Flow Brass S - Steel X - Nozzle X R - Ruby O - ObXidian HO - High Flow…
Having trouble exchanging the blades on your Philips Trimmer Series 5000? This 3D-printed tool eliminates the frustration - no more struggling with sharp edges. Usage: Place the trimmer with the blade facing down into the tool. Hold the…
This file set lets you build a bite‑sized version of an industrial plate heat exchanger—ideal for classroom demos, scale‑model process plants, or just nerdy desk décor. The design has two end covers which clamp a stack of corrugated…
Summary This fan holder is suitable for standard 80 mm PC fans. It allows you to click the fans into place on your refrigerator's heat exchanger. Thanks to the improved cooling, the compressor runs for less time to maintain the…
This is an Intake/Exhaust Grille for standard air exchanger exhaust ports. My air exchanger kept getting cluttered with bugs. This cover is held on by friction and 8mm magnets. I've added mesh small enough to keep the bugs out if the…
DAMMIT BOBBY! Add to your collection with this 1:12 scale propane exchange station. I included my label template in the photos so that you add the labels to your build. I'm not sure if that will work but its worth a shot! Enjoy!
Underware/Multiboard-compatible mount for attaching the ADSBExchange Blue USB SDR dongle. Top clips helping to secure the dongle are spaced out wide enough that you can add a heat sink to the dongle if needed.
3D printable topographic miniature of Jersey City, Exchange Place - 🇺🇸 United States Capture the beauty of Jersey City, Exchange Place 's city landscape with this topographic miniature! This 3D model represents the geographic area around…
Thanks to https://www.thingiverse.com/thing:6332706 I was able to quickly create a slightly different version with some other types of actions. The rules for the game are that everyone starts off holding the wrapped present that they…
Folding utility knife. Liner locking design. Takes standard utility knife/razor blades. When you blade goes dull, don't sharpen it, exchange it! Requires one M3 x 10mm screw. Prints as one assembly with built-in supports. Print Settings…
I made this for our bearded dragon enclosure. We live in a cold climate so circulating fresh air all the time can make it difficult to maintain constant temps inside the enclosure. We already order these activated charcoal filters for our…
I made the bottom and sides solid instead of vented. Used the original lid
This clip is used to hold the flapper door of the air exchanger in place.
Introduction I liked the air exchanger model from user gwg, but I thought I would be able to make some changes. I hope you find them useful. The top has been changed to a solid peice, and you must use a modifier to use hexagonal infill to…
Just half a year before I puzzled over the problem how you could tell the internal angle of a n-corner-shape by how the shape corner touches an outer circle. :-) (I intended to solve it in my head, just for the fun, not by looking in…
How it works: Everyone form a circle with all gifts (wrapped) in the middle. Start with the youngest/oldest/tallest/shortest (whatever qualifier you want). Roll the die. Do whatever it says to do. If you have no gift to pass or unwrap,…
My dryer stopped drying after four years. After cleaning it, I decided to do something about it so I wouldn't have to go through this again. I couldn't find anything interesting in the pre-made models, so I designed my own attachment for…
Just half a year before I puzzled over the problem how you could tell the internal angle of a n-corner-shape by how the shape corner touches an outer circle. :-) (I intended to solve it in my head, just for the fun, not by looking in…
Here you can find 3 Minifigures. You can exchange the hats. Print instructions Category: Toys & Games Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: 0,2 Infill: 10%
This is the water cooling setup I use in my CorEssentials BETA for the E3D Chimera Aqua. Obviously this will fit most other printers. You can find out more about the machine on GITHUB: https://github.com/MacNite/CorEssentials To built…
This is a tripod system that has twist-lock mounts to suit many applications. I currently have a case/mount for the Arducam CS mount camera , and in the future will add other camera mounts. Also different mounts with a ball joint, gopro,…
I needed a quick fix for our old bedroom were right now renovating. So i designed a hook in Fusion 360, together with a pin system so it doesnt rotate with only one screw. (You basically drill a 3mm diameter hole right next to the hole…
Customized version of https://www.thingiverse.com/thing:1919974 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=1919974 Instructions Using the following options: pipe_inner_diameter = 8…
This is a remix of Gaba Ghoul's great painting holder, but with printable screw-on-top exchangeable bases, so you can switch between several minis without ever touching them. Sources This was inspired by…
Soap holder with exchangeable bottom. Bottom has a diameter of 113.6mm and 3mm height, in case you want to make your own
🇩🇰 Velkommen til Danmark Welcome to Denmark! ---------------- Update, April 16, 2024 - We are devastated from the news that a most unfortunate fire destroyed this building of such historical importance. We hope our model brings comfort…
Be the king of whatever you want to be... With this crown! This crown comes with a slot for a tag where you can insert a piece of paper, to become whatever king you want. Originally designed this for a friend of mine but thought you might…
Designed this for desk at work. It is designed after an A-Type Heat Exchanger Channel. The Filler Files slide into the pass partitions. You can scale them to allow longer or shorter items to fit into the pass partitions. I Assembled parts…
This is a bundle from a Heat Exchanger I am working on. I modified it for the Business Card display contest, but was too late. I have included a picture with locations of where I recommend putting supports. In my pictures you can see I…
The coaster consists of two parts, the base and an exchangeable plate with text on it. The plate can either be printed in with color change at font height or be painted afterwards.
Stand your extruder upside-down with this, to aid in the exchange of the nozzle.
I liked the idea of the EAB knife I remixed, but as a print-in-place design the tolerances were pretty floppy. So I ended up redesigning the mechanism and making a few other minor changes while I was at it. I went to a non-print-in-place…
Modified version of Zacbond 's Bentusi Exchange for large scale printing. I've made two changes here: Resized to be in-scale to the Kushan Mothership. Split into sections for easier printing. Joiners included, everything should…
My design for AntiCovid mask with exchangeable paper filters Print instructions Anticovid-19 3D printable respirator The respirator is supposed to be use for individual protection of healthy people. Do not use a respirator for patients…
I've gotten tired of gothic terrain and wanted something different. I'm using for Battletech but ruleset agnostic. I'll continue to put more models out in the line. Prints fine without any supports. Prints as one file or split into two…
Newly designed articulating arm for Raspberry Pi camera V2 module, inspired on existing designs but fully remixed for the purpose. Fits the original MK2 and MK3S Prusa printers. Arm with 4 degrees of freedom, for perfect positioning and 4…
A small fixture to fix the Cover during the exchange of the HotEnd - No more annyoing during change of noozle And also put no stress on smd plugs, cables pins, .. Easy to print , need only 2 M4 bolt, fixing is done by Slot and magnet It s…
Mount for Gerber EAB (Exchange-a-Blade) folding utility knife. Fits both Original and Lite versions of the Gerber EAB knives. https://www.amazon.com/dp/B002RILCLY/ Includes slot for integrated 6x20x2mm magnet (optional) to retain the…
Small Dead Blow Hammer for model building, etc… The TPU faces can easily be put on / switched out. The handle screws on. Handle size: 125mm Hammerhead size with faces put on: 80mm Printing tips: Print the faces in TPU, 100% infill (I used…
I have often thought a fully automated version of RoboRally would be incredible. This is my first step on that path. I have converted the six boards from the 1995 version of the game into a static board. This is broken into four 6"x6"…
My new YouTube Channel: https://www.youtube.com/channel/UCnnw56J\_TeOsF4M\_F5pPPJQ Hey! It's getting hot! Do you have one of those cheap-o mini-fridges that plug in to your car's power socket and keep all of one can of soda moderately…
For my Living Room Ventillation from Envervent the Pulley for the Heatexchange broke. I printed it with PETG 0.4 Nozzle 0.2 Layer 30% Infill 4 Perimeters on my Mk3s+
It's the same fit as https://www.printables.com/model/302219-customisable-stamp-seal-stamp. There you can find a blank stamp to add your own hanko seal. The base model has a ~21mm size and the seal itself shoud be the size you want, matbe…
This is a case for a RaspberryPi Zero W or Zero 2W and an RTL2832/R820T2 Stick. It is used as an ADSB Tracker for Flightradar24, Flightaware, ADSBExchange. To make it as small as possible, you will have to take the Stick out of the…
Since I'm driving a van, I've often had the problem that I can't reach easily machines at barriers or toll stations. They are often too low because they are made for normal cars. Sometimes there is also a higher control panel for trucks,…
Wall mount to hold two ADSBExchange SDRs (Blue & Orange). I built this to clean up the wiring for my ADS-B feeder in the garage. These SDRs can get warm, so I printed this out of ABS. We are moving into winter now so cooling isn't an…
Printbed Scraper that uses a 85x54mm plastic card. The plastic card can be replaced without tools and both sides can be used. The advantage is that the plastic card is harder then printed structures but soft enough to make sure there is…
The prints from the OpenPress Print Exchange are 7x7 cm. Hard to find frames that fit. OpenPress never published the files for their frame design. I remade theirs and a second “floating” style frame. That one comes with an inlay to give…
Needed something to label the keys for my XP PEN Deco 01 V2 as I tend to forget what's on what key across different programs. The labels can be replaced by different stripes. Buttons can be replaced from top. Thus, you can use…
The Samsung tumbledryers equipped with a heatpump have a heat exchanger component that requires periodic cleaning. Samsung supplies a brush for this with a lovely suctioncup to attach it to things so you can be certain it comes falling…
Storage box for the original tools that arrive with the K1 printer. The box has the basig grid from gridfinity (no magnets) and is stackable. I divided the nozzle storage space into 5 areas and left a flat surface so you can add a sticker…
This part is prone to break on all Lancia Betas the white one) This specific one is modeled for the first series. You may need to slightly adapt the narrower part for fit with a file as the available space is very limited.
Our lab only had one rack suitable for small protein purification and buffer exchange columns, so I had to come up with a solution. The openings are designed to accommodate, for example, Cytiva Miditrap or 5 mL gravity flow chromatography…
I'm using a Mele Quieter PC and the Pegasus Astro Powerbox Micro on different scopes: a Celestron Edgehd 8, a TS Optiocs CF Apo 90mm and a Lunt LS60Tha/B1200/CPT. I wanted a solution to quickly switch the computer to a different rig. I…
