19 modeli
this is a housing for a usb-serial converter I recommend ISO7380 M3x6mm screws, but the print also provides clip-in without screws Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0,2mm…
A case for a FTDI Adapter FT232RL. Pretty tight fit. https://cuitbuilts.wordpress.com/2018/03/04/ftdi-adapter-ft232rl-case-3d-print Print Settings Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: No Supports: No Resolution: 0.2…
i changes it a littlefit to make it suite to my ft232rl board
A minimalistic case for the USB-TTL module HW-417, which uses FT232RL. This is widely available on AliExpress and co. The modul needs no support and assembly is done without screws or other tools. Printing: Layer height: 0.2mm Infill:…
The enclosure is for the FT232RL based USB-serial converter board sometimes referred to as YP-05. It has a six pin header at the short side, with pins for GND, CTS, VCC, TX RX and DTR. A jumper allows selecting 5V or 3.3V for VCC. My…
Just a small case for the Case for Hailege USB zu RS485 TTL Serial Converter Adapter FT232RL 75176 https://www.amazon.de/dp/B07Z1V5WQS
Snap fit, no hardware required. It's a tight fit for the PCB, which ends up helping hold it in place.
A simple case that I remix for the FT232RL board with USB-A.
Snap fit case - keeps it on securely, but can be pried off to change voltage level from 3.3V to 5V :)
I needed a case for my Gimx adapter, so I built one. It consists of three parts: the main case, a separator and a cover. The used parts contain: - Arduino Pro Micro Type C - FT232RL - Small wires - And the 3d Printed case parts…
A housing to fit a cheap USB-C to UART adapter. This is a remix by modification of the original FreeCAD files of the mini-USB version. Changes: redrawn the USB-C connector opening added recess with generous clearance around connector…
For the realization of this small box you will need: USB converter: https://www.gotronic.fr/art-convertisseur-usb-serie-ft232rl-gt1125-26140.htm Wires with their X6 connectors of your choice. Model used in my case:…
A OpenSCAD case for AZDelivery FT232RL adapter, to fully enclose the adapter, with "pad" to ZIP-tie the jumper cables. Originally the ZIP-tie pad was flat, but it was way too easy to break it off. Then I changed to this triangular-ish…
A small box for the Sparkfun FT232R breakout board, useful when you need just the Tx and Rx lines. Printed in transparent PETG, so the lights are still visible. Make sure your board fits, as the box is quite tight. The OpenSCAD source…
Just a small case for the Case for Hailege USB zu RS485 TTL Serial Converter Adapter FT232RL 75176 https://www.amazon.de/dp/B07Z1V5WQS
Snap fit, no hardware required. It's a tight fit for the PCB, which ends up helping hold it in place.
A OpenSCAD case for AZDelivery FT232RL adapter, to fully enclose the adapter, with "pad" to ZIP-tie the jumper cables. Originally the ZIP-tie pad was flat, but it was way too easy to break it off. Then I changed to this triangular-ish…
The enclosure is for the FT232RL based USB-serial converter board sometimes referred to as YP-05. It has a six pin header at the short side, with pins for GND, CTS, VCC, TX RX and DTR. A jumper allows selecting 5V or 3.3V for VCC. My…
A housing to fit a cheap USB-C to UART adapter. This is a remix by modification of the original FreeCAD files of the mini-USB version. Changes: redrawn the USB-C connector opening added recess with generous clearance around connector…
