Liczymy pasujące modele…
I designed this vent system for the WhamBam HotBox to vent fumes out my office window, particularly when printing filaments like ABS. It uses a 75mm 12V blower fan, some 1/2" ID flexible tubing, and optionally hose clamps to help keep…
Made this as I wanted to use the LACK table I had. The HotBox is slightly larger than the table surface, so it was not possible to put it directly on. There will therefore be a small gap between the table and the box. Have tried to…
I used flexible PLA for the insert. This will provide protection to items that are often made of glass. Has room for tools you might need on the go as well. The insert is a snug enough fit. I did leave wiggle room incase you wanted to…
This design is released to the public domain for the starving people in [[your country]] or to heat water for a temporary solar shower. A solar collector made with waste aluminum foil and a standard Amazon box. The foil has been water…
I created this press-fit adapter for Wham Bam's Hot Box for resin printers to fit a noctua 92mm fan for the exhaust instead of using a 60mm fan. I assume this might work for other 92mm fans as well. This attached to the base print file…
I love Wham Bam Hotbox for my Prusa, so I am designing various accessories for it from time to time. This time it was spring sheet holder, which accommodates all three sheets while keeping each easily accessible and which plays well with…
HotBox - a tiny enclosure heater A compact 200W PTC enclosure heater designed for Klipper-based 3D printers. Just 100mm wide, 52mm deep and 177mm high. WARNING: This project uses a resistive heating element inside an enclosed space. Built…
Chamber Heater Mount for RatRig V-Core 4 (QIDI Plus 4 Heater) This mount is designed to install the QIDI Tech 220 V chamber heater (the same one used in the QIDI Plus 4) inside a RatRig V-Core 4 enclosure. It provides a clean and solid…
I recently got Wham Bam Systems' “Resin Hotbox”. It has a usb extender that mounts in the front facing, but with it installed, it can't be folded up nicely, and without it there's just a hole. Since I won't need it at all in my setup, I…
The main body of the adapter wiggles into the exhaust port of the HotBox. I'd recommend screwing the provided nut so that the flat side faces the main body. That should hopefully make the connection a little more airtight. I could only…
I created this simple bracket to hold my Wham Bam HotBox on top of the 24x24x0.79-inch porcelain paver my Prusa MK3S+ sits on. It's a pretty loose fit so the HotBox can slide on and off easily. The paver provides a little friction so the…
If you have a Prusa and a Wham Bam HotBox (or other chamber with a slot at the top), this riser will lift the Prusa filament holder above the HotBot. If you like my designs, please consider supporting me on Patreon.…
Here is a simple, two-piece cup that allows you to turn the vent hole in your Wham Bam HotBox (v2) into a catch-all for small accessories. Printed with Printed Solid's Jessie PETG, but PLA would work fine as well. No supports needed. The…
I wanted to prevent my Wham Bam HotBox from moving around when I open it up. These slide under the bottom walls and can be attached to your table with double-sided tape. Prints four nicely at .3 layer height, 15% infill, no supports.…
Simple plugs to stuff the filament holes of the Wham Bam HotBox. In one plug I have added a hole that serves as a filament guide.
The HotBox is slightly wider than the Ikea Lack table, so this mount extends to support the HotBox. I have an Ender 3 S1, so the height was made to just barely clear it. This does leave a gap around the bottom; not ideal for chamber…
I did not make the foot file included with my upload. That was made by psdesign and posted to Thingiverse at this link . I made the 50mm extension block. I bought the Wham Bam Hotbox Mega for my Ender 3 Max. I was pretty sure it would be…
I purchased a hotbox after I installed my case. this will allow you to use this wonderful case and mount it directly ontop of the hotbox.
English: I treated myself to a small PTC heating block along with a temperature control module from A... (they are also offered together). The goal was to assemble the part as compactly as possible, so it could easily be placed in the…
