2512 modeli
For the most up-to-date version of this design, check out the Makerworld version. It's the original threaded dragon egg, great for Easter egg hunts, gifts, and Game of Thrones fans. This is my made-from-scratch design from 2022 that has…
***UPDATE*** I've had a couple of suggestions come in (thank you @Roman_1037762!) that I'd like to implement over the next couple of days. The first of which is a clockwise flow for folks south of the Equator. Or maybe you just have a…
I added holes to allow fixing this Zipper Slider Jig with clamp . Clamp can be used on the sides, front or back
My old Version of a low poly Jesus was garbage. Hopefully this makes up for the old versions lack of inspiration.
A very minor improvement to the screw mount remix of the honey comb screwdriver holder. This version Has fillets/chamfers around the outside edges to make it more pleasant to touch. The screw holes are slightly widened for M4 countersunk…
The famous disc shooter has three issues that this remix improves upon: The last disc in the magazine has poor shooting performance because it is deflected by the lever. This is resolved by adding a disc-shaped lid to the end of the…
This is a fan cover for the FLSUN v400 that is a bit further from the fan (+4mm) and should reduce a bit of the noise. Modified the file to add more structural support to the side-pins and also added a few more slots to enhance airflow.…
This design is a further development of my model 646358. Sometimes I need to sand or polish a small area. I don't like to prepare then my belt or vibration sanders. That is why I designed this very simple flexible disk to be used by a…
I created these Plant Pot Spacer Rings to tackle a common problem: stagnant moisture building up at the roots of plants in flower pots. After noticing some of my favourite houseplants struggling with soggy soil, I designed these rings to…
Custom cover to improve Microtik CRS310 cooling and meaningfully reducing noise by replacing the original 40mm DC fan with a pc case 140mm one.
This is a remix of the silica gel container by the user TC! I used the container A model that fits Prusament spool Diameter 50 mm Height 70 mm - fill the container with silica gel perls - add a sensor module - put it into your filament…
Based on the FlexiRex improved, this variant is getting ready for St. Patrick’s Day. In addition to the normal Rex the model also has a Jaunty Hat, some terrible facial hair and is holding a Shamrock. In the pre-sliced models fuzzy-skin…
This pair of models is a replacement Beyblade arena foot and mounting plate. Stock height is maintained The design should also allow repair of an arena whose mounting squares have split or broken, as it uses the outer two holes and…
Redesigned parts to use on the A3+ Drawing Machine uploaded by nicom1234. These use nuts instead of inserts in locations where I found my inserts were too annoying to install. I uploaded only the modified parts, you can download the rest…
Rubber Duck combined with realistic Virginia Class Submarine parts and cool sunglasses for style points! A fun collectible for rubber duck fans with submarine interests. Use the .3mf “modular” file paired with the “accessories” file to…
I remodeled the glide from the linked model. The original glide has a cutout and ramp to more easily allow the drawer to be installed. There's a bump in the track on the drawer that presses down on the glide. The ramp makes the drawer…
I had to very slightly increase the size of the circuit board mounting holes, just using a drill bit by hand, to get the board to drop into the bottom of the case. I printed with PLA and have had no heat issues running the circuit board…
02/05/2025: Improved version! There was an issue with doing print-in-place. The offset was not large enough to prevent fusing of the two parts during printing. This has been fixed. Use a screw driver through the middle opening to work the…
I had a doozy of a time getting the original version printed. I preferred printing Mr Otter sitting up, as pictured, but the bottom of the figure is rather not-flat. After messing around and trying to find a solution, I threw in the towel…
The original slide switch knob is not very ergonomic - so break it off and replace it! You have to break off the original knob. So do this at your own risk! I have printed the new knob in red PETG using tree supports and 0.15mm layer…
The added cutout makes it easier to remove the Speedmarker from the holder without risking damage to the plastic knurled
Door handles are a custom design with: Magnets very close together for max strength The same 20×6×2 mm magnets as the rest of the enclosure Printed screws Hinges are modified with: Reduced magnet distance Printed screws Allows moving the…
This design improves the original Bambu Lab reusable spool holder in the following ways: Allows you to see how much filament is left on the spool and uses less filament to print the spool due to the hexagon pattern on the sides. Also, the…
Projectvideo: https://youtu.be/SNWnS3XnjX8 I have been experimenting with a breakaway wingtip to improve on the silhouette of my design to match the real F14 better, while still being print-in-place and articulated. The wingtip breaks of…
Remix of Tronnic's bridging tower, with the temperatures from highest on the bottom to lowest on the top. This way, you shouldn't experience clogging issues if the lowest temperature is not enough to properly melt the filament. Many…
Print, assemble and play directly, no screws needed 8-11
Introduction How to read: The current hour points to the current minute. This is a rework of the wandering hour clock by clockspot : https://www.printables.com/model/69885-wandering-hour-clock I changed the mechanism, they did the concept…
Counter Bin - Improved Design for Effortless Kitchen Clean-Up Model Overview: Introducing the Counter Bin , a refined and enhanced version of existing kitchen counter cleaning solutions. This model combines the best features of two…
Improved Auto Coin Sorter - Coin Roll + Classic Version New in latest version 7.528: AUD - Australian Dollar update only. 50 cent coin dimensions increased to match the circumradius of the 12-sided coin. Should sort and stack just fine…
If you would like to download this, please do so from MakerWorld - https://makerworld.com/en/models/96340
The 🥰 BoxTurtle's 4-in-1 hub can be a bit “ temperamental” 😖 when loading filament in certain situations (especially on lane 4 ) with the filament getting caught and stuck in the bearing recess at the end of the filament path. There is…
To support me the most, please download from MakerWorld Link: https://makerworld.com/en/models/170277#profileId-186972 Hate having to use a plyers to remove the bit? Well no longer. This remix has relief cuts on all the corners meaning…
This was made for use with the DIY enclosure available here . HEADS UP - 1 of 3 - new better version of this! I've published a new, improved remix of my popular side-mounted spool holder — PLEASE NOTE: it's not just about the four…
All props to Pattersaurus on Thingiverse for this. * You'll need THREE M3 x 8mm Screws / Bolts (no nuts) to attach this to your machine. * ****PRINT ORIENTATION**** - fins and holes face down on plate: Just as the first photo, place it on…
So I just received my new Sunlu S2 Filament Dryer and it had the chance to be better than my current favourite, the Eibos Easydry. It gets hotter internally and heats evenly from all sides. There are however two major design flaws that…
Please leave a like and rating and consider posting a make if you print and enjoy the project! Also check out these designs of which I offer hardware kits for: Zc Aus Znc Aus Znc Aus Cosmetic Part Variants Zinc .50 Zinc .50 Cosmetic Part…
Found with a heavy plate that I wanted to display that the original felt like the balance was off and could easily fall over when bumped. I have copied the summary from DanRom624 (original from Thingiverse:…
I got some Sunlu Gold PLA for Christmas and I knew what I had to print with it. It won't kill any werewolves (yes I know those are silver bullets don't get mad at me you can print it in silver), but man does it look sick. I changed the…
I was looking for a silencer and a protective grille for my K1 side fan. There is a wide range on offer here, but any grille in the airflow can increase or decrease the noise. As I didn't want to test everything, I constructed my own. My…
FAQ Q: I printed your enclosure and I can’t figure out how to install the filament sensor / spool holder. I’ve looked on YouTube for installation videos and still stuck. Any help would be greatly appreciated. A: Not long after the initial…
This is a completely redesigned fan shroud for the Prusa i3 MK3S/+, which not only delivers fantastic airflow like the old Mk3 shroud did, but which also sits far away from the heatblock and will not melt when printing at high…
I attempted to use some 3D-printed 18650 spacers, but they weren't ideal. The injection-molded design you can get from aliexpress has two identical tabs on each side, which makes the other printed alternatives weaker. This updated module…
A Remix of McGybeer's classic articulated lizard, with wider clearances so it can be printed smaller (my Ender 3 can consistently handle it at 0.55 scale with no issues). The ankles are also improved because the original looked a little…
I took David6722's genious OTF Design and tweaked it a bit, I added places for screws, a pocket clip, altered the button and made a few more improvements. Prints very easily but may need some supports on the newly created overhangs. Print…
This fan duct improves the air flow so the overhangs are better (up to 70º with very good quality, 3rd picture) I recommend to use Prusament PC Blend-Carbon Fiber or PA11-CF, because they are heat resistant and to reduce weight mainly,…
Projectvideo (F14 with breakaway): https://youtu.be/SNWnS3XnjX8 I have been experimenting with a breakaway wingtip to improve on the silhouette of my design to match the real MiG better, while still being print-in-place and articulated.…
The original model was already pretty good, but I wanted the same style of drawer for everything, whether I want to use it with or without bins. Also I absolutely wanted a pull-out-protection. I also wanted labels, so I added slots for…
This updated version of my Zoom Phone Tripod tilts to any angle, including tilting forward for those awkward zoom yoga classes. Collapses nicely for storage. This version fixes a few issues: the legs snap into place more firmly, the jaws…
Improved FLSUN V400 Fanduct Note: Fans are glued to stock fanduct but they can be peeled off easily with a cutter blade. Edit 05/11/22: New Fanduct allowing an overhang of up to 70/75° to be achieved
Make sure to enable "detect thin walls" for printing! Hi, this is my improved Version of my Fidget Toy. It features a lighter and more consistent spring design which can also be removed. If you are not happy with the resistance you can…
Put simply - So easy to remove they fall out. UNTIL you put something into them, then so tight they might even hold tighter than the original design. How? Magic of course. The inserts for attaching to the wall also have the same cuts to…
V5 For P1P and X1C As this is skipping the LIDAR but keeping the Bed Leveling if desired. Date : 5 March 2023 Improvements: -Improved the overall speed of the start gcode -Reduced the purge of filament by a factor of 21 times 5mm vs 105mm…
Since i was a little bit disappointet of the relatively low noise level of the original V29 whistle, i had to improve it. This whistle has larger cavities and therefore a lower pitch. The interval between the two tones is larger and more…
This is a remix of ricktu's Fractal Pyramid on Thingiverse that is more reliable for slicing in Cura 5.1.0. When sliced in vase mode, the original model had thousands of retractions on the first layer. So I edited the original models in…
More stylish! More functional! More printable! This is an improved version of my earlier guitar capo that includes a number of improvements: Rubber in the presser bar frets the strings with no buzzing and with less force. (I've also…
Version Two of my reimagined spool winder. Les Kaye's model is really nice, but as I mentioned in my previous remix I ran into several issues (some mechanical and some cosmetic) that I felt could be improved, hence my Reimagined Spool…
Most Rocktopus have a very rough transition between head and body. I rebuilt this Rocktopus from the original Dr. Smolder Bravestone and the latest version of the mini octopus and made a nice smooth neck. The 3MF file is from Bambu Studio…
Improved Auto Coin Sorter - Coin Roll + Classic Version New in latest version 7.527: Improved geometry to increase reliability and accuracy of the sorting. Improvements: Sorts into removable coin tubes to facilitate both general operation…
The arm file is a 3mf that modifies the arm joint by adding a negative sphere body to make it attach better to the torso. You will need a slicer like PrusaSlicer that supports this. I've also attached a head and face insert that may need…
lundiplutzmus created a brilliant design to hang sock, face-cloth, handkerchief, etc. on the rod of a dryer rack (aka airer). But even brilliant doesn't mean there are no details that can be improved ;-). So I tried a few: I rotated the…
Drop in replacement for the hips. I know there are already improved hips for the dummy 13 but these are different I swear! I always had trouble with the other improved hips either with printability or with assembly. So here's my take on…
Version 2 - moar magnets: After feedback about the camera not sticking - probably due to weaker 6mm x 20mm x 2mm magnets than the ones I had available, the model was revised with the following changes: The 6mm x 20mm magnet is…
This is remix originally by RoboCop0815 ( https://www.thingiverse.com/thing:4441407 ) Improved trigger via handle. For left handed or right handed - your choice :-) Use PETG if you want it stronger. How it works: Standard print settings:…
A small modification of the bearing-less mini wheel by mrplasma ( https://www.thingiverse.com/thing:4498704 ) which is based on the pixel2 design ( https://www.thingiverse.com/thing:3049220 ). Details I noticed that in the original design…
These are ultralight boxes, yet they're durable enough to hold heavy items. When gripped by the sides, they don't feel flimsy. They lack magnet holes and have a flat bottom, making them perfectly compatible with the cost-effective…
Magnetic to attach to the metal bottom of a toolbox and hold the ratchet better. Modular design allows for customization to your needs. The integrated linking pin can be easily cut off with flush cutters. Should fit most ratchets, 1/4…
This is an improvement on the rather popular "Floating Cup (smoother look, foolproof assembly)", https://www.printables.com/model/164778-floating-cup-smoother-look-foolproof-assembly . See that model for some notes and directions of how…
Summary This is an improved version of the iPad stand. Here is what I changed: Added the knobs to the inner part to keep it in place when the stand is folded Reduced the gaps between the moving parts to make the model less wiggly Rounded…
FAQ Q: I printed your enclosure and I can’t figure out how to install the filament sensor / spool holder. I’ve looked on YouTube for installation videos and still stuck. Any help would be greatly appreciated. A: Not long after the initial…
An improved version of the OEM cable clip on the x-axis of the elegoo neptune 4, 4 Plus, 4 Pro and 4 Max. It doesn't pinch the cable like the original one does and has an angle that prevents the cable from touching the z axis' lead screw.
Redesigned holder (V2) with improved threads that do not need to be scaled down/up. Just print all parts 1:1. Less material and shorter print time. Recommended print settings: Layer height: 0.2 Mode: Speed Infill: 10% Material: PLA (PETG…
New improved version for 2026. It is broken into three parts. https://www.printables.com/model/1622682-ufs-170-ultimate-most-accurate-eiffel-tower-for-it Please send me your feedback. Thanks. I visited France this year and I was in Paris…
This is an improved version of the print-in-place dispenser for lickable treats for cats. It reduces the messines of using such treats and allows to retrieve every last drop from the tube. The model was tested by printing in PETG using…
Cover the fan cable. Better magnet fit to prevent it moving, I hate the “clic, clac” sound when opening and closing door. Center better my improved fan duct Lighter weight I recommend to use my Improved Fan Duct:…
Improved version of the 3D Pull Copter Finger Ring with a different rotor design. NOTE: Models not compatible with original design Features: Improved rotor design (bigger and angled differently) Somewhat longer key for easier use Uses M3…
Here's my wire and cable holder, specifically designed for the Skadis storage system. This innovative holder is designed to fit into your Skadis board, providing an elegant and practical solution for cable management. Its design is…
alpokemon did a great job modeling the outside shape of the 'Among Us' characters ( https://www.thingiverse.com/thing:4595212 ); however, the joinery I felt could use some improvements. I changed the Legs, Heads and Guts. The major…
bunckle sam (sorry for using the original pic wanted it to be recognizable as pretty much the same thing)
I was trying to find a model like this, but I couldn't find it, so I decided to make it myself. Very easy to print, Under 20 min. HOW TO USE: Gently insert at the top of the strawberry, where the crown is fixed to the strawberry. Make…
Remix of earlier designed privacy cover. Improvements is that the base/holder fits better on the camera, and the amount of material required is lessened.
Changes: I was getting feedback that the tail was very delicate and you needed to be careful while pulling it off the build plate. And it also looks kinda wonky with the small head and massive arms. So I upscaled the head and tail parts…
NOTE: Do not print with supports. The model is designed to print without the need for supports Print settings (example) Rafts: No Supports: No Layer height: 0.2 mm Infill: 100 % Thank you @SpiderGod_2164882 & @Chris_Walnut_3378485 for the…
Based on the original Thing from K_Lab - thanks for the source Fusion 360 files: https://www.thingiverse.com/thing:3533859 and the remix from Theo Tinjum:…
Hello 3D Printing Enthusiasts! This Thing is my version of Soldering Tweezers! Simply print the long base, 4 handles, assemble, and you get a super versatile wire holder for your soldering station! The original tweezers design was remixed…
I was frustrated by the need to re-attach the screws to the standard Creality bracket whenever I need to run input shaping with my Sonic Pad. So I created a version which simply slots in (firmly) to a semi-permanent bracket on the…
The original model was good looking and very sturdy. The only problem was that when printing on its side a part of the “upper” edge of the charger cutout would be printed into thin air. To be able to print it without supports or without…
Improved Auto Coin Sorter - Coin Roll + Classic Version New in latest version 7.527: Improved geometry to increase reliability and accuracy of the sorting. Improvements: Sorts into removable coin tubes to facilitate both general operation…
This is a new, improved version of my original vase-mode desiccant container. I changed the side holes to extend inward rather than outward, so the outer surface is much less likely to poke holes in your filament storage bags. Total print…
See description over here: https://www.printables.com/model/39810-improved-all-in-one-temperature-and-bridging-tower This is a remix for Prusa Core One / Core One + / Core One L. 05.06.25 : Added MMU3 profile. 28.12.25 : Added optimized…
I like the vertex fruit washer from Perinski , but it requires support for nearly the complete bottom. This model is a fixed version. It requires minimal support and prints nicely. If you wonder if this really works, it does. Kids love…
For a lot of helpful details/info please consult the main Teaching Tech listing here: https://www.printables.com/model/864950-open-source-spacemouse-space-mushroom-remix This final assembly video explains all about my remixes in this set:…
This is a remix of this: https://www.thingiverse.com/thing:2999507 I just made some of the overhangs more printable while maintaining the aesthetic. Will print then upload photo. For this type of model I recommend variable layer height if…
This is a remix of Prusament spool bird feeder by Enos. The original model has holes in the roof and small food capacity. No supports needed, print with non-toxic filament (ABS or ASA might not be the best choice). Simply glue the main…
This is a remix of falangy's bunny ring holder with an improved tray to fix an overhang issue. I’ve also set the bunny back from the center of the tray I have a few other similar remixes: Cute bunny (you are here) Sleepy fox Dancing fox…
When you wash your car with a bucket of soapy water, the dirt that comes off the car ends up in that bucket. This grit guard captures that dirt and keeps it from getting back on your sponge and scratching the paint. It was inspired by the…
Accurately bending leads on radial, through-hole components like capacitors and resistors has never been this fun! :D Inspired by the fancy tools used by the talented Marco Reps in his GPS Nixie Clock video , I modeled a Biegelehre from…
This is just an improved Printer Profile and Print Settings for the Kobra S1 that increases printing speeds significantly, while not loosing out on quality. I have increased the max speeds for the motion limits of the printer as well as…
I flattened the base of the claw for better adhesion, and re-oriented it to remove the need for supports. PS The symbols on the Gold claw are not correct. They are actually for the Emerald Claw. - thanks to TacoScientist for pointing that…
This design optimization is for people who has cooling efficiency problem with his S1 and you don't want to add any weight to this super heavy Sprite thing. Since I found that the S1 has more stringing than the V2 has. I made some…
Lots of little changes for a better print! See below for a list of edits. Includes a 3MF file for Bambu Studio. The arms have a ball and socket and can be posed in lots of directions. Arms and one-piece skull print with supports.…
![Skyrim Dragon Claw [improved printability]](https://media.printables.com/media/prints/192164/images/1786079_8aa72619-5f92-466c-9a64-627303046a56/abd3bfabd2f6f1685f666f3cd719b3eb_display_large_19.jpg)
