Liczymy pasujące modele…
Needed a stand for my Keystep 37 and found https://www.printables.com/model/57533-arturia-keystep-60o-stand by boomNinjaVanish Unfortunatly the Keystep and Keystep 37 differs by ~5 mm so I drew this one with inspiration from above…
I really liked the Arturia Keystep 45° Stand by 7824c5a4 but 45º was far too steep of an angle for my liking. This remix relaxes the angle to 60º and raises the height by about 50 mm. Print Settings Printer Brand: Creality Printer: Ender…
DCAPS are designed for the Behringer Model-D case and can be used either as table top (perfect with Arturia Keystep) or as an extension of an Eurorack Modular System. To mount the DCAPS on the original Behringer Model-D case, remove the 4…
Korg nanoKontrol2 holder for Arturia Keystep for my perfect DAW setup. You can use the original screws for attachment. Printer: Ender 3 V2 Filament: PLA Infill: 25% Duration: 2h per part Support: not necessary
I wanted a 45 degree stand for my keystep so that it could sit behind my normal keyboard on my desk. The keyboard's 17mm rubber pads fit into the holes on the stands. The left and right sides can use the same model, but the right side of…
Extension of original model: https://makerworld.com/en/models/141454#profileId-154130 A slide-in attachment for the Korg Volca Series Honeycomb Stands. This attachment goes under the Arturia Keystep and will stop the Volca units from…
Adaptation of original model: https://makerworld.com/en/models/127751#profileId-138245 Honeycomb stands for Korg NTS-1 with an extended base to fit the Arturia Ketstep. No longer will the NTS-1 push away with use during play due to the…
With this stand you can mount the Korg Volca series synthesizers on Arturia Keystep 32. This allows you to free up the space on the table, and also in this way Korg Volca doesn't block the cables and ports on the back side of Arturia…
A slide-in attachment for the Korg NTS honeycomb stands. This attachment goes under the Arturia Keystep and will stop the NTS units from sliding around on the table when in use. The extension legs fit flush below the Keystep with the…
Quick remix of nice knob and D-shaped potentiometers. 3 versions of 2 heights, 12mm (two left ones) and 17mm, both fit under the DeckSaver simplest - no marking 1.5mm wide 0.6mm deep notch multicolor Measurement on my old, used Keystep,…
Adaptation of original model: https://makerworld.com/en/models/127742#profileId-138237 Honeycomb stands for Korg NTS-2 Oscilloscope with an extended base to fit the Arturia Ketstep. No longer will the NTS-2 push away with use during play…
I printed these in PLA+ and glued together with super glue. The 3mf has dovetail joints I cut with .1mm tolerances. If I were to print this again I'd do it in ASA or ABS and weld it together with acetone. I used insta set to activate the…
With this stand you can mount the Korg Volca series synthesizers on Arturia Keystep 32. This allows you to free up the space on the table, and also in this way Korg Volca doesn't block the cables and ports on the back side of Arturia…
These are mounts to use on Josh-3D's Eurorack case if you print the “Angled 2 Unit Stand” I printed this to fit my system, which the keystep fits in with very well. Main case 46 HP, 2 side cases 36HP, dual case stand Angled 2 unit Stand.…
DCAPS are designed for the Behringer Model-D case and can be used either as table top (perfect with Arturia Keystep) or as an extension of an Eurorack Modular System. To mount the DCAPS on the original Behringer Model-D case, remove the 4…
These are mounts to use on Josh-3D's Eurorack case if you print the “Angled 2 Unit Stand” I printed this to fit my system, which the keystep fits in with very well. Main case 46 HP, 2 side cases 36HP, dual case stand Angled 2 unit Stand.…
Stand for the Arturia Keystep. You can use the original screws for the stand attachment. PLA. No supports. Layer high: 0.2 Infill: 20% Printer: Ender 3 V2 Print duration: 2h40min
