P
Printablesalexb
Asus WiFi Antenna Holder with Cable Management for Louqe Ghost S1
It allows you to roll up and hide the excess cable, and to snap its 4 feet into the top ventilation grid.
- Pobrania
- 385
- Polubienia
- 52
- Ocena
- 4,8
Wyniki wyszukiwania: louqe
Liczymy pasujące modele…
P
Printablesfrankgreens
Louqe Raw spacer for Noctua 120x25mm fans
10.5 mm fan gasket for the the Louqe Raw rear exhaust. Remixed from the official Noctua 120mm fan spacer. Changes from the original design: Cutouts to fit around the raw's outer rails. Increased height to 10.5mm. Enlarged the 8 centering…
- Pobrania
- 140
- Polubienia
- 14
- Ocena
- 0
P
PrintablesIconic FAB
LOUQE RAW S1 Slim Fan Top Hat - lines and hexagons
Raw S1 Slim Fan Top Hat - Lines and Hexagons versions with fan top and bottom braces. Recommended print settings: Layer height: 0.2mm. Extrusion width: 0.4mm, forced. Infill percentage: 42% Infill type: grid, gyroid, honeycomb, triangle,…
- Pobrania
- 129
- Polubienia
- 15
- Ocena
- 0
P
Printablesabcpdo
Louqe Raw S1 Top Hat
This is a mod to add a 120mm x 25mm fan on top of the Louqe Raw S1 case. Print the fins facing down. Use some glue on the printer or the edges will lift. In addition to the screws included with the case, you will need 8 m5 fan screws.
- Pobrania
- 122
- Polubienia
- 17
- Ocena
- 0
P
Printablesdrewman
Louqe Ghost S1 Case Feet with I/O
This is a set of feet for the Louqe Ghost S1 PC case that add front I/O using the motherboard's USB3 and USB2 headers. These are modeled for specific hardware, but it should be fairly simple to modify these to your needs with the included…
- Pobrania
- 104
- Polubienia
- 30
- Ocena
- 0
P
PrintablesDrew Heavner
Louqe Raw S1 Stand
This is a stand for your Louqe Raw S1 small form factor computer case. Due to the design of the case the GPU exhausts its heat out of the bottom which leaves only a small gap from the feet and a small opening in the back that is shared…
- Pobrania
- 96
- Polubienia
- 13
- Ocena
- 0
P
PrintablesMaven
Louqe Raw Top Mounted Fan Adapter
Intended to mount the Noctua NF-P14r 140mm round fan on top of the Louqe Raw S1 case for improved air flow and heat extraction. Remove the aluminum top plate of the Louqe Raw S1 case to reveal 4 holes in square pattern that the pins of…
- Pobrania
- 64
- Polubienia
- 6
- Ocena
- 0
P
PrintablesMartin.Ö
Louqe Ghost S1 feet and handles (Mac Pro inspired)
Decided to change the look of my Louqe Ghost S1 mk3 and add spacing between the desk and case to give it more airflow. I opted for a Mac Pro type of styling with carrying handles on top of the case. The handles are mostly for aesthetics…
- Pobrania
- 64
- Polubienia
- 13
- Ocena
- 0
P
Printablesrodoca
Louqe Raw S1 Stand (Parametric)
Stand for Louqe Raw S1, standard model increases height by 30 mm. Contains Fusion360 file with parametric variables, just change the “Height” variable, leave all other parameters as they are.
- Pobrania
- 50
- Polubienia
- 2
- Ocena
- 0
P
PrintablesKert
Louqe Raw S1 Rear Fan Bracket - FDM Optimized
This is a 3D printing optimized version of thearamadon 's rear exhaust bracket for the Louqe Raw S1. His bracket allows you to mount a gasket on the fan much easier, for much better temps in the case. You will still need to print off the…
- Pobrania
- 36
- Polubienia
- 1
- Ocena
- 0
P
PrintablesHackolyte
Feet for the Louqe Ghost S1 case
Simple M3 mountable feet for the Louqe Ghost S1 case. Gives slightly more space for the case to breathe without looking too ugly. I've also heard reports the original, sticker feet have a tendency to peel off over time. You'll need 6mm or…
- Pobrania
- 30
- Polubienia
- 7
- Ocena
- 0
P
PrintablesKert
Louqe Raw S1 Top Plate Spacers For A12x15 Fan
Need: 4x M3x10 for spacers. 2x M3x5 or M3x6 for block off plate. This is a mod to install a Noctua A12x15 fan on top of a Louqe Raw S1, while still using the stock top plate. This moves the top plate off the fan, but keeps a low profile…
- Pobrania
- 22
- Polubienia
- 0
- Ocena
- 0
P
Printablesntpham
Louqe Ghost R1 - Mobo Standoff Sleeve
This is a sleeve around the troublesome mobo standoff of the Louqe Ghost R1. This part provides more surface area around the standoffs so that users cannot over-tighten mobo screws to the point of shredding the mobo. 2 models are provided…
- Pobrania
- 21
- Polubienia
- 3
- Ocena
- 0
P
PrintablesDuncan Idaho
Louqe Raw S1 3D printed PSU Bracket with M.2 Holder
Remix of a remix of thearamadon's PSU brackets. Allows the PSU to be mounted vertically. This makes it much easier to access the power switch and shortens the distance between the PSU and motherboard. Contains a holder for an m.2 drive…
- Pobrania
- 13
- Polubienia
- 3
- Ocena
- 0
P
PrintablesZilver
Louqe Raw S1 Power Button
Replacement button for the power switch, which is prone to being destroyed. Print in TPU and remove the original rubber and rubber gromet, but leave the tape attaching the metal bridge of the switch. Then attach with double sided tape.…
- Pobrania
- 7
- Polubienia
- 0
- Ocena
- 0
P
Printables
Louqe Ghost R1 Top Hat
A very rough update from jonathan's design to allow for the additional length, width and hole placement. Design still needs correctness for spacers and a way to keep the sides hooked. 31mm and 40mm stls available but easy to scale.
P
Printables
Louqe Ghost R1 - GPU Support Bracket
This GPU support bracket is designed to be installed on the open rail of the motherboard tray. This part will require 2 M3 heat insert (up to 8 mm thick). Please print on its side as in the last picture. No support needed. There are 2…
P
Printables
Louqe Ghost R1 power button bracket
Here's a 3D printable power button bracket for Louqe Ghost R1, since some of the buttons at least for this first batch are not aligned properly. This model allows you to adjust the placement of the button both horizontally and vertically.…
P
Printables
Louqe Ghost R1 - Replacement Feet
Made these because case feet were missing from my Ghost R1 batch 1 order. Printed mine in TPU. I went with the 5mm size but 7mm may be better for giving a touch more breathing room especially if using the case in a non-flipped layout. As…
P
Printables
Louqe Ghost R1 - Replacement Button
Available flat (as original) or with a slight chamfer. Print facing down on textured PEI, no supports needed. Use with ➡ Ghost R1 power button bracket by Levis | Download free STL model | Printables.com
P
Printables
Louqe Ghost S1 Feet
A friend wanted feet for his Louqe Ghost S1 and use the original holes on the bottom. Category: Computer
P
Printables
Louqe Ghost s1 Mods
A couple holders for 40mm case fans and a spot for the wrench they give you. I printed in PLA and found no warping but your results may vary. I wanted to mount a few 40mm fans in spots around the case to play with cooling. I didn't notice…
P
Printables
Custom Top Plate For Louqe Ghost S1
This Custom Top Plate is for the Louqe Ghost S1. It helps to reduce unnecessary noise from fan turbulence. Keep in mind to have a clean cable management (risercable and GPU powercable), otherwise the cables might reach into the fanblades.…
P
Printables
Louqe Ghost S1 Vertical Stand
A vertical stand for the Louqe Ghost S1 small form factor computer case. Should work with any case version, any top hat, both orientations. It's designed based on official 3D case model. Included are several versions, which differ by leg…
P
Printables
Remix - Custom Top Plate For Louqe Ghost S1 with added fan guard
My fans were hitting the PCIe extender and the power supply cables so I added some fan guards to stop this.