Liczymy pasujące modele…
Printing Recommendations: Use adaptive layer heights (up to 0.2mm max) for optimal surface quality and faster print times. Tree supports recommended for clean and easy support removal. Components: Heltec LoRa32 V3 NEO-6M GPS Module…
09.02.2026 Update: add new Front part with new necenano support, which uses low-profile USB-C connector. 18.02.2024 Update: add Base.stl file and upgraded step file In relation to the original model: - the profile of the adjoining surface…
M5Stack Cardputer is interesting piece of hardware. It's quite hard to use when flat on the desk. This angled stand will raise it by 15°. Stick rubber feet to bottom to stop it for sliding. The stand slots into LEGO-compatible holes on…
This is a CC1101 case to use it with the M5Stack Plus 2.
After trying various webcameras in different positions, I’ve learned that ultra-high definition isn’t necessary. And placing the camera away from the heated bed or toolhead may not capture the most exciting angles, but it’s definitely…
09.02.2026 Update: add new Front part with new necenano support, which uses low-profile USB-C connector. 18.02.2024 Update: add Base.stl file and upgraded step file In relation to the original model: - the profile of the adjoining surface…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
This model is a 3D‑printed rear enclosure (back box) for the M5Stack Tab5, featuring an integrated storage compartment with a sliding lid . The M5Stack Tab5 is shipped without a rear cover , leaving the battery protruding and exposed.…
M5stack atomS3 and S3R enclosure. if you want less tight add 0,1 or 0,2 mm in size.
Created a spacer so I could add GPIO headers and a bit more space for larger battery. Short M2 screws needed to hold the spacer on. Make sure there is enough clearance as the front cover screws use the same thread. You can probably…
Based on my euro modules , this version is designed to hold an M5Stack Atom S3, but could easily be adapted to work with the other Atom modules. I've included two models based on my two euro plate designs (one with two clips, one with a…
I designed this magnetic mount to bolt to the Rubigrid inside my truck. It prints in 3 pieces. First, the AMPS mount base, which can be installed on an appropriately sized Rubigrid or mounted to a dash with VHB tape. (If mounting to a…
Slim enclosure for Heltec Wireless Tracker & M5Stack CardKB with Battery An enclosure that fits in Heltec Wireless Tracker, M5Stack CardKB Keyboard, a battery (up to 38mm x 70mm x 5mm), and a cutout hole for the LoRa antennae. Mainly…
Box for Stamp Fly, Atom Joystick and short USB-C cable. Stamp Fly and Atom Joystick link: https://shop.m5stack.com/products/m5stamp-fly-with-m5stamps3 https://shop.m5stack.com/products/atom-joystick-with-m5atoms3 Printed with Bambu X1C in…
The M5Stack Cardputer pins extender, gives to opportunity to use 8 extended pins [ 5V, GND, G1, G2, CLK, DAT0, CMD, 3.3V ]. Throw this pins you can easily attached CC1101 , NRF and more other modules. For assembling process and additional…
The M5Stack Cardputer Modular Expander is an extension board designed to enhance the capabilities of the M5Stack Cardputer. This expander provides you oportunity to add add additional modules: WIFI external antenna, CC1101, IR Transmitter…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
AMF Grader - Open Source M5Stack Weight Sorter for Fruits and Vegitables. Summary AMF (Aizu Matsubara Farm) Grader is an open-source fruit sorting machine designed specifically for persimmons but adaptable for any fruits,vegitables and so…
A case for the M5Stack Atom Thermal Printer . I love the cardboard case that's supplied with the Atom thermal printer but mine started to tear after a few weeks so I decided to design something that could hold the printer and 2 rolls of…
Back plate for M5Stack Cardputer enabling easy modifications (via provided .f3d file) , or change with origial one. Remix it as you like. You maybe will need to increase tolerances becouse I tried to make all holes as tight as possible.…
Warning: In asembly you will NEED hot glue gun for glueing battery module to the plastic frame-thing also be aware and do not overtight screws otherwise screw holes will break off. Antena mod for cardputer providing extended wifi and…
Print tips: Lay the faces of the surfaces flat on the build plate. If you have a well dialed in printer you will not need to use supports. If you don't, use tree supports. Please see the readmes in the original. You may want to increase…
This is a NRF24L01 case to use it with the M5Stack Plus 2. I did the case but the unit i bought sadly does not work propertly.
Casing for electronics: m5stack Atom Lite Battery Pack RFID module (or RFID2, they are the same size physically) Uses m3 heat inserts to keep the top and bottom secure. Lid is recommended to be printed upside-down (such that your heatbed…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
Deutsch: Dies ist ein Adapter, um einen M5Stack Tough an einer Quadlock Aufnahme zu befestigen.Dies ist ein Adapter, um einen M5Stack Tough an einer Quadlock Aufnahme zu befestigen. Danke an @fabilandwehr für die Bereitstellung der…
This stand features a compact footprint with integrated 16 mm mounting studs, providing secure attachment for M5Stack 16 mm modules, including the Atom Lite. The base is designed for both tabletop and desktop use, offering stability while…
Wanted a small holder for the AMG8833 without opening up the M5stack so this one just holds onto the rear of the M5 with 4 magnets that hold onto the ones in the original battery case. Nothing fancy, I just wanted to protect the somewhat…
This is a box that slips over an Anker 511 USB charger and is intended to hold the electronics for a minimal ESPHome analog sensor reader using the M5Stack NanoC6 ESP32C6-based MCU and the ADS1110-based ADC module. I have included build…
This is to magnetically mount the M5Stack NanoC6 . It is designed for 6mm x 2mm magnets . I include STEP and Fusion 360 files for easy remixing. Features: Nice friction fit; arms are slightly tapered so they flex a little and maintain…
I put port covers on everything I know, but normal silicone ones aren't available for many ports and connectors used across the Maker / Electronics / Arduino / RaspberryPi world. So this page is where I put all the connector cover models…
See-thru design is simple, keyboard text show thru, yet provides protection. Print using clear TPU on smooth build plate. Heat stake bottom edges with soldering iron set at 220C or lowest setting possible.
A simple remix of hippazoid case but for the Cardputer ADV version and the M5Stack logo. I kept the original parameters for the print: 2 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height.
Simple wall mounting bracket to hold the ATOM Matrix with clearance for HY2.0-4P connector. My use case didn't require access to the pin sockets on the back so I left them blocked off. Sized for a #8 screw but it's a fairly close fit…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
This model is a 3D‑printed rear enclosure (back box) for the M5Stack Tab5, featuring an integrated storage compartment with a sliding lid . The M5Stack Tab5 is shipped without a rear cover , leaving the battery protruding and exposed.…
Case for people who want to use a keyboard with their T114. This requires you to have small battery terminals to insert into the battery housing area, wires to solder onto the terminals, and the 1.25 molex pico blade connector to connect…
M5stack atomS3 and S3R enclosure. if you want less tight add 0,1 or 0,2 mm in size.
I have lost the top cover of my M5Stack PoE CAM and designed a new one. Snaps into place. Printed at 0.20 layer hight.
ein Aufsatz für das M5Stack Atomic TF Card Modul für ein eigenes OLED, dass über I2C angebunden wird. Info zur Hardware unter https://cool-web.de/esp8266-esp32/m5stack-atom-lite-vorstellung.htm
A magnetic case for the M5Stack StopWatch ( Store , AliExpress ) for a better Grip. Uses 4 6×3mm round magnets for holding the device. Has a passthrough for straps and cable, protects the power button from getting accidentally pressed.
A friend of mine uses a M5Stack ATOMS3R to point his Arrow II antenna directly on satellites. With this adapter, the M5Stack can be used as a scope to point the antenna directly on satellites or fixed points in the sky.
M5Stack Paper Color e-paper Display (SKU: C151) Stand, with integrated USB C cable management. A portrait version stand is also available . Designed to integrate with the display's built-in clip indentations. The display is angled for…
A desk stand for the M5Stack Dial, angled for easy viewing and tapping while you're typing. Features: - Angled mounting bay holds the Dial at a comfortable viewing/interaction angle - USB-C cable cutout in the back for power without…
M5Stack Paper Color e-paper Display (SKU: C151) Stand for portrait device orientation, with integrated USB C cable management. A landscape version stand is also available . Designed to integrate with the display's built-in clip…
This model is a modified (Remixed) version of an original work I found on Thingiverse made by daffniles. The modifications were made to be able to house the M5Stack GPS unit and to return the Groves cable back into the unit so it would…
Give your M5Stack Dial a permanent home with this custom-designed workbench mount! Created for an interactive Sparkle Motion demo featuring Adafruit's LED technology, this mount securely positions the M5Stack Dial along the edge of a…
A storage case for the Cardputer ADV with the LoRa Cap (with the included stock antenna). External case can be printed using your choice of material-PLA, PETG, ABS, etc. The inserts should ideally be printed in TPU for shock absorption…
MLX90640 thermal camera cover for M5Stack locator for solder MLX90640 on pcb. Print Settings Printer Brand: Deltaprintr Printer: Deltaprintr Assembled Rafts: No Supports: No Resolution: 0.15 Infill: 33.3% How I Designed This Try Thermal…
Mounting plates/covers for M5Stack Atom Lite ESP32 IoT Development Boards. I use these awesome little and cheap boards for measuring water levels in my tanks, light control, remote buttons and more! I couldn't find any covers. cases or…
camera 5M is small PoE Camer what could serve for any purpose, I need simple holder for “ Articulated Arm ” . Enjoy :)
These mounts are designed to work with M5Stack modules and the cameras. They are very simple in design but work very well. I haven't tested the camera tripod mount yet, this one needs a square nut inserted for use on a tripod. I designed…
Just a test of some new skills. multimaterial and magnet insertion using the logo of a favorite microcontroller company. Pause to insert magnet at 3.4mm. Color change to blue at 5.2mm and then to black at 5.8mm. Started with glow in the…
Revision history: V1: Initial release The case is for this camera: https://docs.m5stack.com/en/unit/timercam_x Photos show it next to the original. The case has a hole for a m5 nut so that it can be fixed to something.
CAD of the M5Stack ASR6501 LoRaWAN module, with antenna. Useful if you want to design IoT modules and just import external components. I haven't modeled the interior. .F3D, .STEP and .3MF included. .STEP and .3MF without antenna. .STEP…
M5Stack is set of electronics development modules. Some of them have cute magnetic stand, but most does not. This one isn't magnetic, but is parametric, so you can change its height, angle... Use M3 screws for attaching the unit to the…
Mettre une pause a 6,6mm afin d'ajouter les rondelles pour faire contre poids Ne surtout pas mettre de support J'ai utilisé deux rondelles diametre 26,5 épaisseur 2mm
Add a pause during the print at 9mm to add washer to give more weight and stability In the holes at the upper add no head screw (M5x15) to have more grip
Gridfinity dashboard module for two M5Stack dials Requires interface plates and magnets to connect to a Gridfinity base plate . Print bracket on the side. No support material needed. You need angled usb-c cables (or just connect power…
An easy way to mount your m5stack core basic to flat surfaces. You will need 4 M3 threaded inserts . I used the inserts from CNC Kitchen , you can allso buy these from many resellers . I designed 2 versions , a thinn one with wall…
Hi everyone! This is my first upload and my first true 3D model edit. This is a protective pelican style case that holds two M5Stack core units. It will hold Core, Core 2, and CoreS3, as well as modules like the Battery 13.2, PM2.5, etc.…
ummary I remixed the very nice M5Stack Wall Mount by Aoshimak. I added a cutout to allow the unit to stay connected to the USB-C port. I also covered over the screw holes and used basic mounting tape instead. Covering over the screw holes…
A bipedal robot built with M5Stack and SG90. PCB gerver and sample code is uploaded to my Github. https://github.com/tomorrow56/M5Stack_Walk-chan/tree/main Product description(note.com) https://note.com/tomorrow56/n/nf83f81b76e1e
Gridfinity dashboard module for 8.8" 1920x480 ultra-wide touch screen and 3 M5Stack dials I used this display: https://nl.aliexpress.com/item/1005003014364673.html (with touch) Requires interface plates and magnets to connect to a…
This is a simple little casemount for the M5Stack ATOM ECHO.
M5Stack AtomS3 Halter für eine 3,5 Senkkopfschraube ---- M5Stack AtomS3 holder for a 3.5 countersunk screw
I am making another model that uses the ESP32 Basic Core IoT Development Kit 2.7 from M5Stack and didn't find a mount I could remix, so I thought I would make one that everyone else can. This mount has holes in the right place for the M3…
Info This Adapter is made for the new m5Stack Unit CamS3. It fits any ov2640 module with a 120* viewing angle lens on it. Just pop open the original housing, and change the module as well as the adapter! Like what you see? Consider…
Mounting frame for installing the M5dial into a standard 57mm avionics hole.
M5Stack Card Computer (Cardputer) Mount compatible with Ikea Skadis Pegboards. Designed in FreeCAD. “split” 3mf file splits model into two pieces if a higher infill percentage is prefered for the back. Otherwise use the STL.
Here's a quick model for anyone looking to design their own keyboard case for the CardKB
Reference model for making cases and such, keep in mind that I measured the physical device with calipers, so it's not perfectly accurate, but that's what you get when a DIY company doesn't release any real specs.
Designed for: Amazon.com: DeWalt DWST14830 - Organizador profesional de 20 compartimentos con divisor extraíble, amarillo/negro : Herramientas y Mejoras del Hogar
Inspired by the flowing lines of muzi's H1 case , my case allows for the following components to be used in your Meshtastic setup: BME280 module for reporting temperature, humidity, pressure, air quality, ... Buzzer for audible…
A replacement bezel for the M5Stack Dial - print in any colour to fit in with the rest of your build. I didn't like the orange and grey scheme, so measured up the parts and designed simplified replacements.
※Need support in the shoulder area. Original works https://x.com/cofelatte_latte https://x.com/skylark_mmm https://x.com/oicchahan/status/1817958229885993281
I wanted something to protect my Cardputer when I carry it in my jacket pocket. Buttons, power switch and SD card are all accessible on the back without removing the device from the case bottom as well as the USB-C port on the right (the…
3D model of the M5Stack CoreS3 loT Development Kit, probably not 100% acurate but is sufficient enough for most things
You can keep the whole logo blue/black or choose to color it with the original colors like i did (in your slicer). I printed mine in PLA/High speed PLA using 3 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height on a…
