24 modeli
MegaXL Spigot SCAR The MegaXL Spigot SCAR (or Silly Scar) is a SCAR attachment for 16mm OD aluminum Nerf hobby barrels that stabilizes darts, is easy to attach and detach, is fully air-sealed, and it allows you to fire MegaXL darts off…
Just a simple model to print to test your bed level. Such a large bed is hard to get on the first shot, this should help you calibrate it. I find it is good to go through the normal procedures for leveling; preheat the bed to your average…
This is a belt tensioner for the X-axis used with ANYCUBIC MEGAX. It will probably work with the CHIRON as well. This is the easiest belt tensioner to install in my opinion. Simply attach the belt clips to the ends of the left and right…
A Bowden to filament sensor adapter to connect your dry box to your filament sensor with a Bowden tube. I use the PC4-M6 version on my Anycubic Mega X together with my filament sensor spacer:…
Important Note: Downloaded file(s) are for personal use. Do not resale. These are inserts for the Nerf Rival Pilot, Knockout, Forerunner, Takedown, and many other Rival blasters. It might bend the hop up tabs a bit on some blasters, but I…
This model is a friction-fit barrel insert for the Nerf Rival Knockout that allows for firing MegaXL darts. No mods to the blaster are required. Just insert into the barrel until it snugs the hop-up (or until you can't go any further).…
The meme machine I've always wanted in real life; a nerf Whizz Banger. See a demo of the original prototype (using ahakelly plus motors) below. This original hits 130 fps! (ridiculous) I've since then been tuning it for Dutch Legal Nerf…
You can use this simple tool to mount a cheap dial gauge to your 3D-printer. This allows you to accurately level your bed surface to an accuracy of .01mm to the z-stops (you still need to set up the Z-offset afterwards) I used this dial…
Print a set of these models and one of your preferred Silly Spigot Nut . You can use 1-½"x3/8" insulation pipe foam to fill the void
This is a pic rail Nerf MegaXL dart holder. I personally use this with SillyButts SCAR barrel to quickly fire off MegaXL. Model should not require supports for printing. Three holders (for a total of 6 darts) can fit on one rail. The…
Update 2024/08/13: Update to all files to now use my Cruller thread profile for printability and QOL. These will have 0 backwards compatibility, so print only v4 options for use together and you'll need v4 for my future expansion parts.…
Remix of the sliding part to a pump grip for comfort and ease of prime. It does go past the rear of the blaster now, so it will need a bit more room behind for the prime, but it's not too bad. I found it best to print it with supports, in…
Cutting jig for creating/trimming Nerf Mega XL darts Are you stuck in a place where you cannot get MXL darts, or just want to try your own luck making them? You can use this guide to help you cut the foam pipe covers to the proper length…
I had an issue with the original trigger that made it so you had to push it on an angle to fire. Just made the part that touched the bungee slightly longer so that it should fire just by pushing it straight up. Should not interfere with…
To be paired with my Marshmallow Blaster Modular Breech , I've created a super simple method to attach a 31mmx33mm aluminum tube (Greg barrel) to launch Mega XL at frankly frightening velocities. Simply thread the 33mm_adapter onto to the…
To be paired with my Marshmallow Blaster Modular Breech , I've created a super simple method to attach a 31mmx33mm aluminum tube (Greg barrel) to launch Mega XL at frankly frightening velocities. Simply thread the 33mm_adapter onto to the…
Remix of the sliding part to a pump grip for comfort and ease of prime. It does go past the rear of the blaster now, so it will need a bit more room behind for the prime, but it's not too bad. I found it best to print it with supports, in…
The meme machine I've always wanted in real life; a nerf Whizz Banger. See a demo of the original prototype (using ahakelly plus motors) below. This original hits 130 fps! (ridiculous) I've since then been tuning it for Dutch Legal Nerf…
Update 2024/08/13: Update to all files to now use my Cruller thread profile for printability and QOL. These will have 0 backwards compatibility, so print only v4 options for use together and you'll need v4 for my future expansion parts.…
Did you know the Big Bad Bow is almost perfectly compatible with MegaXL darts? Ditch those 9-inch arrows and increase your capacity at the same time! I designed this mod to be reversible, but I'm not sure why you would want to remove it.…
This is a blank adapter mount for a Megax MX-70 Tripod. I designed it to mount an outside laser light onto my tripod to use inside for a party. It can be modified to add any bracket of your choosing. I have included the STEP file for use…
A remix of the Anycubic MegaX x-axis belt tensioner by penguin-holic (https://www.thingiverse.com/thing:4908450) The tensioner is 10mm longer, enabling using it on just the left side (from back perspective) instead of having to replace…
This part was designed to replace the barrel/spigot of the Lanard Max Shot. I didn't have any of the original missiles this blaster came with, so I designed this part to make the blaster compatible with MegaXL darts as well as standard…
Blast three MegaXL darts at the same time. Here you go! No support required, but you might need a brim.
