Liczymy pasujące modele…
Tool to tighten/loosen ring securing cartridge in a Moen Sense faucet. Mine kept loosening up and I was trying to turn in the ring with a screwdriver which didn't work so well so I designed this. Hope it helps. Hex grip for hand…
This additional mount point for the Moen Engage Magnetix handheld showerhead was designed for those that sit on a shower bench and need a close place to hang the showerhead without standing to use the original mounting point or dropping…
Bought an aquarium vacuum that uses the flow of water from a faucet to start the siphon. We have a big fancy Moen Pull down faucet and none of the included adapters connected to the hose where the sprayhead/fauct unscrews. Thanks to the…
This is a tool to disassemble the sprayer head on a Moen faucet to access the aerator and clean it.
Viel Spaß! Category: Signs & Logos
Needed a replacement Moen install tool, to remove my Moen faucet. This took the place of Moen part 118305. I uploaded the OpenSCAD file as well, which will let you customize it to your own size or for some other project. You can comment…
I had a broken faucet retainer that kept leaking. So of course 3d printing to the rescue! it saved me $50 in the end, considering you cannot buy just the piece that was cracked. You'd have to buy the entire handle ($50) or replace the…
Moen cartridges last a long time and are pretty easy to get out – unless they've been in there for decades. This tool will allow the twisting action to get it free. If the cartridge has been in there for decades, then you will need to…
Same size as Moen Kit #180158 https://shop.moen.com/products/180158 This fits the aerator in products like Moen Graeden One-Handle Lavatory Faucet - Model 84136.…
I've made a few improvements from the original design, and hopefully should be a bit beefier than the original which had very thin walls seemingly prone to cracking at the top. Also included a place to snap the mesh filter into the print…
27 OCTOBER 2024 UPDATE: V2 with slight tweaks and used Fusion threads instead of the prior process. Added STEP and draft files for gaskets. I printed with the faucet side down and slim tree supports for the inner lip area.
Overview: This is, mainly, an OpenSCAD design so you can adjust all the parameters of the design as desired or needed. The following are provided: One .scad file containing the parametric model. You will need OpenSCAD for your OS of…
I grew tired of the sprayer button breaking endlessly on my kitchen sink so I designed and printed this replacement. Print instructions Category: Replacement Parts Summary I grew tired of the sprayer button breaking endlessly on my…
Still somewhat a work in progress. Updates may happen. Replacement parts for the handle adapters/connectors that come with the Danco brand Tub/Shower Trim Kit for Moen faucets. I have made models for both Type A (Posi-Temp) and Type B…
Hand tool for tightening the spindle retaining nut on a Moen single handle kitchen faucet Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 25 Filament: eSUN PLA+ Category: Hand Tools
This project's scope was to catch drips from children's wet hands operating the faucet and optional soap dispenser. The design is for an 8" spacing Moen Eva faucet but could work for other 8" faucets. The soap dispenser tray was designed…
The faucet handle in my rental house fell apart so I printed this replacement in Colorfabb Glowfill PLA
I created this to adapt my Moen Monticello faucet assembly for use with the newer Moen 1225 replacement cartridge after the original cartridge model was no longer in production. The recommended handle interface part#109113 included in the…
I have a Moen Magnetix shower head which is OK. I purchased a cheap Tiktok shower head that suprisingly works very well. I designed an adapter for the Magnetix system. This adapter uses a 30mm x 3mm magnet that I assembled with super…
Its a sleeve to protect the sharp corner of the bathtub faucet. I also added a mickey face at the end for fun.
I printed this with thick walls (~1.8 mm) and light infill (5% gyroid) using PETG. ~0.6 mm bottom layer ~0.9 mm top layer Also made a spacer to fill the gap back to where the mounting screws attach so it's less likely to deflect under the…
Our original acrylic handle for our Moen Posi-temp shower was looking worse for wear after many years of use. The original handle had a teardrop shape that was not only difficult to turn with wet hands, but especially at times for my…
Upgrade your shower with this custom-designed knob tailored for Moen 1222-style valves. Featuring a precise 10mm D-shaped stem slot, this knob ensures a snug, reliable fit for your valve. The ergonomic 45mm diameter and 35mm height…
Moen 6410 EVA Valve Stem Extension. If you happened to break the Valve extension for this model, Moen wants you to buy the entire Handle assembly (they do not sell the extension seperatly). Print small side down with a full brim and 3-4…
Wanted to re-position my shower head a little higher and at a different angle. There is a retail version of this available but this was more fun and customizable. I used 2 stacked 15mm x 3mm magnets to hold the shower head in place. A…
This is a tool to disassemble the sprayer head on a Moen faucet to access the aerator and clean it.
This is a place I made when we had the tub-spout replaced. The previous contractor thought a hole needed to be WAY bigger than the copper pipe. This allowed the hole to be covered and sealed with a little silicone.
Two large grip points on each side make pulling the handle forward to let water flow easy and safe for those with grip related handicaps. The large lever rotates the knob clockwise / counterclockwise to adjust temperature. The large lever…
Upgrade your shower with this custom-designed knob tailored for Moen 1222-style valves. Featuring a precise 10mm D-shaped stem slot, this knob ensures a snug, reliable fit for your valve. The ergonomic 45mm diameter and 35mm height…
This is a place I made when we had the tub-spout replaced. The previous contractor thought a hole needed to be WAY bigger than the copper pipe. This allowed the hole to be covered and sealed with a little silicone.
This is a fixed version of the Moen 90274 valve stem extension for two handed tub and shower control. It does not have the stop for easy no support printing - I made this as a temporary fix until my part came in. You will also need to…
A simple little print to help get off the nut to a moen kitchen sink faucet when it's in a super tight spot
Male adapter for Moen's weird proprietary 5/8-16 UN 2B kitchen sink threads to a 5/8 garden hose female. Probably print in PETG but my PoC is working with PLA and I'll re-print with PETG once that breaks.
This holder allows quick and easy access of your Moen workstation cutting board near the sink without having to be on the sink at all times There is a slight angle to it so after you clone the model mirror one of the two so that they…
Simple shower knob for a Moen shower valve. Mine broke so I made this. The inside diameter of the outer wall is 49mm. The center portion inner diameter is 9.8mm, and flat to flat measures 8.23mm. Category: Bathroom
This is a fixed version of the Moen 90274 valve stem extension for two handed tub and shower control. It does not have the stop for easy no support printing - I made this as a temporary fix until my part came in. You will also need to…
Replacement cap for Moen Kingsley facet handles. I have painted the model to match my oil-rubbed bronze finish (114343ORB). Used small o-rings I had laying around: 011 Buna-N O-Ring, 70A Durometer, Black, 5/16" ID, 7/16" OD, 1/16"…
Made this to change the angle of the shower wand when installed in smaller showers.
I had a heck of a time with a plastic nut that holds the faucet to the cabinet. It was tight space and I could physically see the plastic nut under the faucet. That an there's not much to grab onto and it was screwed in tight. I created…
This is modeled after the COLD side (blue) the HOT (red) side may need to mirrored to fit correctly. Unsure if this may work with other models. Check your own. The handle and it's stem unscrew from the base of the faucet. The handle and…
Moen Shower Replacement Eco Performance You can scale it to your desired size if u have a different shower
Moen's Attract with Magnetix shower head comes with low pressure fittings in the grip. This causes water pressure that is too low for most consumers. Conversely, removing the fitting entirely results in excessive pressure that can also…
The side spray of our Moen faucet was leaking. I made this plug to replace where the side spray hose plugs in so that we could still use the faucet. I slipped the o-ring from the hose connector to this plug.
This is a replacement plastic insert to the Moen 1417BN. Mine broke after I dropped something on the hand shower head and it snapped off, but don't tell the wife that. To my horror, the list replacement price for the whole elbow is a…
The knob for my shower broke. The parts are Moen. So I needed a new Knob. It was $50 at the Home Despot, and I had just finished building my own 3D printer from scratch — so when you have a hammer, everything is a nail. It probably costs…
Minimalist Shower Valve Back Plate for Moen Valve DISCLAIMER: I can't be liable for any damages. The model is available for free download and use. If you still want to invite me for a coffee for my effort, troubles and time, you can do it…
I needed an adapter to clean my fish tank (I have one of those python attachments). But we just got a new moen bathroom faucet and it didn't fit. The threads on the moen seemed to be about 21mm wide and 1.5mm pitch. The hose part is about…
Summary I had a failure of one of the wall mounts for my Moen Eva towel bar. After scouring the web and calling Moen, the part alone is not available (you must re-purchase the entire item if not under warranty). So, I took some time and…
# Moen Soap Dispenser Locker Nut <br> ## What This is the locker nut that clamps the soap head to the sink base <br> ## Printing This is the fifth revision. I printed on * 100% infill * Fine mode in flashprint * Took just over two hours…
I recommend printing from PETG with a 0.15 mm layer height. This adapter is designed specifically for the Moen Boardwalk 18" towel bar sold at Bed Bath & Beyond.…
I made this in college when my landlord failed to replace the shower knob after it had broken the 2nd time in a month. This is a replacement shower knob based on the Aperture Science logo and a Moen single shower knob. Higher levels of…
Moen bathtub faucet handle's center cap was missing when we moved in. The white part of the center cap was printed in PETG with .1 mm layer height. It press fits into the faucet handle. The colored inserts for hot/cold were printed in PLA…
Moen toilet paper holder template for drill holes and use for leveling, 16” center to center.
Got annoyed one day that my Moen shower knob snapped for the 2nd time and so I created a beefed up one for 3D printing. In retrospect I probably just needed to replace the stem and/or lubricate it a bit but oh well. Unfortunately I…
My Moen shower head has the main head and also a magnetic mount wand. There is a little handle that diverts the water from the main shower head to the wand. It turns about 120 degrees back and forth to change the flow. The ribs act as a…
My shower handle was too loose after the center rod was extended. The extra play made the shower leak if turned to far. I made a longer version of the internal plastic piece in the shower handle, and now everything works great! Printing:…
Special mounting washer for some Moen kitchen faucets. This is for the faucets that have an extendable hose sprayer built in. It's used to mount the faucet to the sink and the metal one that comes with it rusts out after 6-7 years. It's…
