Liczymy pasujące modele…
The Fosi Audio V3 Mono is an incredible piece of engineering, but it uses its entire aluminum chassis to dissipate heat. When sitting flat on a desk or stacked, airflow to the bottom of the unit is restricted. This stand helps solve the…
Add another level of customization combined with a boost in performance by adding or stacking this modular cooling block to your Corsair Dominator Titanium memory modules Variants Single or dual fans 10mm or 20mm fan heights Fan Mounting…
MonoBlock v3.12 (6MM & 8MM) axis This block will not only enable you to convert your standard Ultimaker print head from 2.85mm filament to 1.75mm filament, but will also enable structural integrity and rigidity for higher quality prints.…
The Fosi Audio V3 Mono is an incredible piece of engineering, but it uses its entire aluminum chassis to dissipate heat. When sitting flat on a desk or stacked, airflow to the bottom of the unit is restricted. This stand helps solve the…
A 1:1 replacement for the stock SV06 Plus carriage, printed in one piece! With all the screw holes at the back retained for mod compatibility This whole design sits within the stock footprint of the stock carriage, no more compatibility…
ANYCUBIC MEGA-S convert to Titan-type Direct Extruder. ==ATTENSION== Not compatible for Original E3D Titan Extruder, MEGA-S's Titan-Type Extruder has different dimension E3D's Titan Extruder. Not compatible for E3D V6 Extruder, MEGA-S's…
The Fosi v3 Mono can get pretty warm (uncomfortable to touch). The V3s have ventilation ports on the side. These stands will hopefully result in better ventilation. Note though that the ones sitting in the middle of the stack have no cool…
Add another level of customization combined with a boost in performance by adding or stacking this modular cooling block to your Corsair Dominator Titanium memory modules Variants Single or dual fans 10mm or 20mm fan heights Fan Mounting…
My aircon monoblock has a square hose adapter for the hot air exhaust. In order to be able to move the aircon but leave the window adapters and hoses in place, I needed another adapter. Maybe this is something you need too :) I printed it…
Monoblock for Ultimaker 1, 2, 2+ This block will not only enable you to convert your standard Ultimaker print head from 2.85mm filament to 1.75mm filament, but will also enable structural integrity and rigidity for higher quality prints.…
MonoBlock v3.12 (6MM & 8MM) axis This block will not only enable you to convert your standard Ultimaker print head from 2.85mm filament to 1.75mm filament, but will also enable structural integrity and rigidity for higher quality prints.…
This model represents a typical modern railway fence and is designed as a single solid piece , avoiding complex assembly. The comb-style structure ensures strength, precise alignment and easy printing , even on small FDM printers like the…
I was wanting to replace the X carriage mount on my SV06. I liked the monoblock that SilencedFrost had created and wanted to adopt it for the LM8UUs used on the SV06. I mostly stayed true to the original, I fully recreated this rather…
this replace all the 4 lane with a single piece, you may require a M3x70 rod instead of using single m3 screws for each lane. in my case I didn't had a m3 rod so I just cut some screws head to fill the shaft area with them
A quick model for a Koenic Monoblock AC to redirect the cooled air into a 150mm hose. Use tape to secure the Hose inside. Split it in half inside your slicer if you have a normal sized printer. The halves can them be reattached with…
Für die Abdeckung für die Ansaugseite werden längere Schrauben benötigt, hierfür habe ich 3,5x16mm verwendet. Teilweise sind an der Seitenabdeckung aber auch lange Schrauben verbaut obwohl hier kurze verwendet werden können, evntl. kann…
Not much to add. Be aware, that 150mm to 100mm is quite a big reduction in surface area. I've used this for a Kibernetik / Coldtek / Nanjo / TCL unit.
My HomeDeluxe MOKLI XL Monoblock AC had an exhaust adapter which was not very stable with a 150mm Hose (the hose was "secured" inside the adapter). With this adapter, you can mount a 150mm hose using a clamp, which is way more stable than…
This is a Corne 36 layout put into a monoblock design. Designed to fit MX switches and a Seamicro controller. Printed at 75% infill to ensure it was stiff and deadened the sound. Uses M2 heat-set inserts in the top plate, and M2 x 4mm…
Micrometer stand monoblock, 0.3 Print it from the side! It has a flat side for that purpose. Sturdy, stable, minimal material. Loose derivative of the nice design of Wehrenseb It is a single piece + the knob Prints without supports from…
This is a remix for Mega-X. https://www.thingiverse.com/thing:3954252 Attach the extruder to the fixed plate. Category: 3D Printer Extruders
Update 2/01/24 It seems that the 15.2mm or 15.3mm versions of the NEW design work best for getting the right size for the bushing holes on most printers. I would say use the 15.2mm. Worst case, if you have a dremel and a large sanding…
Another variation of the tented Dactyl Manuform keyboard
Update 2/10/24 If you guys need anythingspecific, please message me. Leaving it in comments doesn't notify me at all for some reason. If you message me, I get an email and I will respond much sooner. STP file added. Update 12/12/23 I…
With the exception of the holes for the set screw on the lower bearing, I kept all the original proportions of the original block. You probably only need to enable the supports in the bearing and shaft insertion holes. I added a version…
