Liczymy pasujące modele…
DJI RC-N1 mount adapter with QuadLock receiver. Use four M4x5 screws and M4x3 nuts to mount the two together. Print with PET-G, 0.2mm layer, 0.4mm nozzle, 50% infill. Use supports for the QuadLock receiver part - print it flat on the bed.…
Connector for Chicco, Baby Hug 4in1 v4 .3mf file has two components(you can separately regulate the length you need for each side). I printed these connectors with 40% infill and the middle section with 100% infill for more strength and…
Can be used to connect a D100 hose to a DN110 system.
Here is a sheet of the hoodoo hex pattern, wilI l update it with a few sizes and the parametric model when done.
Knob for Caravan Truma Vent. Truma Trumatic Vent TN1 TN 1 Drehregler Regler für Lüftung / Ventilator 220V
this elongates the linear rail in case you have a shorter one to use. it fits the table top cut out as well.
Here you will find really basic alignment tool for 2020 profile with the MGN9 & MGN12 linear rails. Proper alignment of linear rails especially on a 3d printer is VITAL to help give your 3d printer the best chance of both working &…
There are 2 versions: The regular, if you love simple things. The clip, more useful in vertical configuration, especially if you need it to stay fixed without holding it with your hands. Every stl contains both versions in order to limit…
在转换到板版后，它更容易保存，可以作为礼物送给孩子，就像乐高一样。
🎯 Silicon PRO 3in1 è lo strumento definitivo per ogni amante del fai-da-te e per i professionisti della sigillatura! Con il suo design ergonomico a freccia e le tre punte intercambiabili, questo accessorio rende ogni lavoro di silicone…
Very simple alignment gauge for mounting an MGN12 on a 2020 or 3030 extrusion. Will work on any 20mm or 30mm T slot extrusion face. Put the linear rail on the extrusion with bolts fitted, place a few of these over the rail / extrusion and…
Complete set of metric nuts. The diameter is 0.2 mm above the nominal diameter in order to compensate for filament printer tolerances. Print with 0.15 mm layer thickness or less. I recommend to print perimeters outside-in, not inside-out…
Quick designed stand for drawing and watching on my iPad
Unfortunately, I must point out: I WILL CLAIM ALL LICENSE/COPYRIGHT VIOLATIONS. Elevate your collection of sports memorabilia with the 3D model of the Airless Basketball, meticulously designed for 3D printing enthusiasts and basketball…
Made some changes. The tube now holds filament roll better in place and does not require any supports and screws. The baseplate is upgraded so it's a little smaller and actually saves more space, now standard-size filament spools fit more…
* v.2.1 made slot support thicker so it doesn't break anymore, requires a little more force to go together but its much stronger. *v.2 Changed dimension to fit Creditcards and can be used as a wallet Perfect for professionals,…
Lets you slide the block off the rail and put it back easily. Tested them with Magicphoenix MGN9H and genuine Hiwin MGN12H blocks and they fit perfectly. Print as-is (on the side) with default settings and make sure you don't have an…
This Upgrade gives you the Ultimate 3018 CNC Machine - PCB's and Aluminium can now be milled accurately. Build Steps: Remove the old X-axis rods and Z-axis carriage Loosen the vertical X-axis mounts and slide them as far rear as they'll…
20mm x 40mm MGN12 Linear Rail Alignment Tool for the WorkHorse 3D Printer but this tool can be used for any 20mm x 40mm frame extrusion and MGN12 linear rail.
A remix of RepresentativeBlink mount for the Afterburner on an Ender 3 with an MGN12 rail, for StealthBurner also changed Added tie wrap holders to the top for cables Removed nuts that hold the two sections together and replaced them with…
Simple alignment tool to install MGN12 rails on 2040/4040 extrusions. Printed myself with PETG-CF , because I was lazy to change filament, but all other filaments should be fine. .STEP-file included, if you want to edit the model. If you…
A rail stopper to screw to your 2020 extrusion at the end of your linear rail to stop the carriage from falling off. It needs an 8mm M3 screw. Remixed from the Voron trident design, and step/f3d file included for modifications.
I just modded the XY Joiner for the Gantry to fit MGN12H Rails instead of MGN9C. WHY? Cause i don't have 9C Linear Rails in stock :) Just the lower part has to be changed, upper joiners still stock. Print Settings Supports: No Resolution:…
A remix that adds a stop to one end of the rail. So the carriage can only be removed from one end, and will not fall off the other. Print on their side, as per the original. I found the MGN9 rail was slightly too loose, and the MGN12 was…
I recommend use 6 bottom layers and 6 top layers to increase the strength of the part.
Sharing my custom 3D enclosure design for the Lenovo M90q Gen 1, featuring the MSI RTX 3050 LP, a 3.5-inch LCD screen, and an RGB fan. This project involved designing the 3D case model using SketchUp and printing it with PETG filament on…
*Please note that this FREE release is the GEN 1 DESIGN. Please visit https://www.printables.com/model/1264527-cbk-skull-rose-commercial-license for the most update-to-date and easiest-print version of the model that includes lifetime…
Was having a hard time finding a good looking and functioning clip for my Apple Pencil, so I made my own.
Ein Gitter, das in die Muffe eines DN110-HT-Rohres passt. Das Außenmaß der Einsteckseite ist 110mm, was dem Normdurchmesser eines DN110 HT-Rohres entspricht. Früher wurde dieses Rohr mit DN100 bezeichnet.
More options and upgrades available soon, free version includes very basic features! Free Version includes: Clean Cooler Grooved with Spout Model Features: Layered STEP files so under the objects tab you can easily color customize without…
EVA3 dropped support for MGN12H and here I am adding it back in! Keep an eye out on www.3dpandme.com for full installation pictures and content. BOM: 4 x M3 inserts Support me by buying your dragon hotend (or any other 3d printer…
this can be used on the Trident This Requires 2 M3 heat inserts in the Key to work properly. 3 M2 heat inserts for the pcb Klicky version This a Mount for the Voron Dragon Burner on a MGN12H. Can be used on any printer with the belts on…
Useful print to have when washing MGN12H carriage blocks in IPA in an ultrasonic bath or when you want to thoroughly clean/lubricate your linear rails without accidentally knocking the carriage off and having to pick up all the little…
This is a installation/allignment guide for MGN12 linear rails on 2020 extrusions. The fit is quite tight so there is no play when installing the linear rails.
I enlarged the model to open the wings of the X Wing and display several spaceships on top of each other in combination with the original print. Orinal model : Display Stand for LEGO Star Wars X Wing by P1R4M4X | Download free STL model |…
Just remodeled the Voron Trident Z Carriages to fit MGN12H Rails, as i'm reusing some old parts for my build. Please NOTE THAT, Positions are all the same, nothing changes. As MGN12H Carriages are wider than your extrusion, you should use…
These linear rail MGN12 and the block MGN12H objects with exact dimensions, are intended as help tools in prototyping and designing. There are 2 types of rails, one without holes, that can be elongated/stretched to any desired length by…
::edits again:: So I've come across a much more elegant solution for the Orbiter 2 mounting setup @ https://github.com/elcrni/Voron-Mods/tree/main/Orbiter_2.0_SB_CW2_Enclosed I recommend this over the one in here. So skip the orbiter…
DN150 lid for IBC containers, with an added ¾" connector (around 26mm outer diameter). The added 3mf file has a negative part to ensure the hole, make sure to open it is Prusaslicer/Orcaslicer if you cannot see it. I am using the existing…
Want to use your 2021 11" Ipad pro as the interface for your DJI mini RC-N1 controller instead of a phone? Don't want to remove the Ipad from the Logitech Touch Combo case ( https://www.amazon.co.uk/gp/product/B07W4DH1Y5 but are ok to…
designed these to fit in the drive drawers for my HPe Blade center. not perfect but they work. they fit a wide variety of HP servers gen8-10. tried to make a version that was easy to remove, but kept the older model in case they really…
Tested on SE. Fits KE. Updated V4 with spot to attach your Input Shape Sensor (WARNING: this mod is not meant for beginners. Nothing wrong with being one but you might be over your head with this one. I am an experienced Machinist and…
made a wall mount for my lego mandalorian N1 starfighter Lego set 75325 probably could use some improvement but it works i printed at 20% infill with supports with my anycubic vyper
Hook for your bag with three position- way to use. 1) Tension on desk board 2) Hook with small diameter (upto 3cm) 3) Hook with big diameter (upto 6cm) Tolerances depend on material you will use, like PETG si more flexible than PLA :)
Top for EVA 3 MGN12H instead MGN12C. For sensorless homing.
This mount is made to accept a dragonburner/mini stealthburne for ender 3 neo printer with linear rail in the x axis. Print with minimum 4 wall and +40/50 infill you can go 100%. Height of cr-touch can be changed when you want . Made an…
What can I use it for? Handle for drawer Print the base model and a additional pole in the size you need. Filament Swatch Just print a few of the base models and use them as samples . KeyChain You will also need paracord for this. Print…
EDIT 7/9/24: Added beefed up design (v5) to resist sun/etc. Use this design instead! Here is a basic AMPS pattern mount to replace the terrible double sided adhesive hand mic holder for ham radios, cb, etc. Print in something that will…
You can use a screw and nut in the top hole to secure the cart for storage https://a.co/d/5vAbloZ I used these grease nipples. I needed to heat the nipple and screw it into the cart. might need to make the threads bigger
My own version for aligning MGN rails. MGN9 and MGN12 version for both 2020 and 2040 extrusions.
A thin comb for hair and beard 2mm thicknes(0.6 mm minimum), 20.6 cm long, 7cm wide
A simple way to mount a BLTouch to voron 2.4/trident/ Ender 5 Mercury one X mgn12H version IMPORTANT: it is recommended to wrap the bltouch in some kapton tape and use a silicone sock to reduce heat transfer to the bltouch
It's my take of linear rail kit I've designed for my Anycubic Vyper. The kit includes the left and right MGN12H mounts that replace the V-roller bearings and original Y-axis endstop mount for 2020 extrusion. [UPDATE] Through some changes…
Update: Added 120mm fan version A revised version which enables 120mm case fans to be mounted as lid has been added. I ran this setup with a fan powered by the AK2 Plus board directly for over a week without any stability problems. Read…
This remix allows you to easily mount an Eddy probe on a Dragonburner toolhead. I used Chirpy's 'Carriage_Base_Short' as the base for this design, making adjustments to fit the probe securely. It keeps the probe at an optimal distance for…
Use 1xM3 screw from your rail or carriage to secure the carriage in place for store or lubing.
Very simple MGN12 Linear Rail plug Can be printed in most any filament. Example is in PLA. Also great in a semi-flex TPU. This is printed in 0.25 layer height with 0.4 nozzle. 0.20 or 0.30 also works well.
I wanted to make a simple case for the smallest ESP32C3 that I could find for use within a Mitsubishi AC. There is a CN105 port on several Mitsubishi ACs that allow you to control the unit remotely without spending $100+ on an official…
My take on the Duender by Sergei Irbis. This version uses MGN12 linear rails with H size bearing blocks and adds mounting points to use end stops if you prefer those to sensorless homing. For the configuration I used, you will need the…
Blank cover for the VW Polo 6N1 or SEAT IBIZA, INCA, CORDOBA
You'll need four M5x12 and eight M3x6 for the linear rail block (M3x8 might work too, not sure) To install it, partially screw in the screw into the hex nut (use the stock ones) to lift the nut, and place the mount over the rail block…
Стационарный кѾрпус для Heltec V3-V4 c воможносью установки энкодера, клавишного переключателя, двух аккумуляторов 18650 либо один 21700. Клавишный переключатель: https://ali.click/hl1puq Рекомендации по печати: Высота слоя 0.2 Без…
I printed it in ABS with 2 walls and 3 bottom layers. The layer height is 0.2 mm. You can enable regular supports.
******************************** Update: I've added a cut out to mount an end stop as I personally need one and I like having the option available for others :) ********************************* This is a remix of Gulsifer's wonderful…
Update (15.06.23) - Now works with the Orbitor, you will need to print Orbitor Bottom Back Brace Orbitor Filament Sensor Orbitor Top Back Brace Orbitor EBB Mount Update - I have added an additional version of the base (withgantrybase),…
Tablet holder for DJI RC-N1 controller (shipped with e.g. DJI Mini 2) Designed to fit an iPad Pro (gen 2018) with Apple Smart Folio on it. Original design by blue_canyon21
CR-6 SE Y-axis Linear rail and MGN12H carriage mount This conversion method DOES require you to replace the Y-axis belt, but unlike some other projects doesn't require you to cut the rail. Required Supplies: 2x 350mm long MGN rail with…
MGN12 Linear Rail Alignment Tool for 2040 extrusion
This is a pretty straightforward design. It covers the end of your linear rail to both align it during installation and prevent the carriage block falling off accidentally. There are two files, they are identical with the exception of the…
It started by finding the original model of the “ Heat Insert Press ” by BaGooN, which I really like! since I still have some iglidur i150 filament lying around, I thought, hey why don't print the rail and the carriage by myself? but the…
Simple and easy. I use the no-screw version, but if you prefer to make it with “ceinture et bretelles”, use the screw version with an 16mm M3 screw and a T-nut. Nothing special to print these things, I just used supports from buildplate…
UPDATE - Included new (untested rear plate). I wasn't very happy with the clamp version to hold the belt. This is more HeroMe-ish. If you try it out, please let me know how it works. I have one ready to test but I just haven't had the…
A Cover for the DJI RC-N1 remote that locks the control sticks in neutral position. This cover makes it possible for you to pack your remote control into your backpack while your drone automatically follows you.
This is a remix of the Prusa MINI Y Axis Linear Rails Mod by Ryper3D that I re-created from scratch from the original Prusa MINI Printable Parts with the following differences: Clean and pleasant aesthetic. No personal logos, crazy lines,…
Hier stelle ich meine Handyhalterung für die DJI RC-N1 Fernbedienung vor. Ich hatte das Problem das mein Handy im Bumper zu dick für die normale Halterung war und ich es immer aus dem Bumper nehmen musste. Ausserdem musste ich immer…
ABOUT MGN12 RAIL BLOCK ASSEMBLY TOOL Precise, printed rail block assembly / servicing tool for MGN12 linear rail carriages. In short - this will allow not to drop your balls :) SUPPORTED RAIL BLOCK CARRIAGES MGN12H; MGN12C Printed Parts…
DIY mini PC NAS DISCLAIMER: this model was built over the Beelink EQ12, however after some research I think it should also be compatible with the Beelink ser5. Hi Makers! I had some 2.5" HDDs laying around my lab gathering dust and I…
I didn't want to buy limit switch PCBs, so I designed an upper mount with an inbuilt limit switch
3in1 Silicone/Caulk Tool What are the three functions? It includes a scraper to remove the old silicone, as well as two round edges with different diameters, to smooth the new silicone once applied. Three versions There is a Mini, a…
Lets save our K1s :-) This is my linear conversion for X axis. Every version i found was complete makeover. Not this one. This is cost effective coz you reuse most of your stock hardware. Designed for STOCK or POWGE idlers. No software…
This is a remix to attach a neck strap to the Dji RC-N1/N2/N3 controllers both for safety, to prevent drops, and stability to make flying a bit easier if you're used to hanging your rc controllers off your neck. Changes from original: I…
I wanted a design to fit an MGN12H rail that I have on my custom printer so I thought I'd alter the existing top on EVA 3 to accommodate both MGN12C and MGN12H
A 120mm fan mount for the “fanless” Topton N100 router PC. It lets you securely mount a fan without case modification.
Remixed backplate to add extra strength, holes for nylock m3 nuts, and flush cap head screws for the linear rail.
Muffenstopfen DN110 nach Norm Zur Abdeckung von Rohren
Remix of thrutheframe 's excellent MGN9C heat set insert press for MGN12 and MGN15 rail. I originally designed this for MGN12 rail, thinking I had some spare. It turned out I had MGN15 and so redesigned the parts for that size. Both C and…
Replace the V-Slot-Rollers on your Sovol SV05 with MGN12H linear rails using these adapters. The belt tension on the Y axis will increase slightly with this mod, but this shouldn't be an issue. You will need some additional hardware to…
X Endstop for Creality Ender 3 / CR-7 made to fit with mgn12 linear rail
Scroll down for English language ;-) ---- Ich benutze ein Iphone 11 Pro mit dicker Handyhülle und kann es nicht an der Fernsteuerung befestigen, da zu groß. Mit dieser Halterung ist es möglich, ein Iphone 11 Pro mit Handyhülle zu…
It is better to print it with structure, and besides the neck is very small so when you print it give it a layer of glue
Minimal print area loose. No end stop adjusting... This project is based on SK-Tank CF BMG Dual 5015s Mount by declinox. https://thingiverse.com/thing:5182358 ) I find his design while looking a project for “MGN12H rail system, BMG…
Stückliste: Linsenkopfschrauben oder Zyl. Für den Halter 2x M5x8 Für den Schlitten 4x M3x6 Für die Winkel 6x M3x8 Für die Winkel 6x M3x14 Einschmelzmuttern 7x M3s Einschmelzmuttern 2x M5s Linearführung MGN12H…
Větrací mřížka pro potrubí HT DN110.
This is a printed adapter to mount the Micro Swiss Direct Drive Extruder for Ender 5 on a MGN12h linear rail carriage that utilizes the CoreXY belt configuration on the Mercury One.1, Voron 2.4r2 and maybe others. When doing the build,…
Shout out to @Bendandsend_757774 for originally designing this MGN12 mount for the Dragon Burner.
Beelink Mini PC 12th Gen Intel Alder Lake N100 tried to keep it accurate to 0.02% mm
Volkswagen Polo 6N1 central console USB charger Insert · Background: I've recently installed a dashcam in my VW Polo, before this I had only the phone holder and I used a cable to charge my phone from one of these car cigarette lighter…
Halterung um einen 20V / 40V Akku von Worx oder Pattfield am IKEA Skadis System zu befestigen. Es werden zwei der Universal Hooks des hervorragenden Sets von CSD_Salzburg benötigt. Die Universal Hooks sitzen bewusst sehr straff in der…
![Alternative Case for AK2 Plus Intel N100 Mini PC (Firebat, Kamrui, NiPoGi) [Updated 120mm Fan Version]](https://media.printables.com/media/prints/926938/images/7229417_abf8bd94-445d-400a-9f74-0e1abaf2ebbb_0b6333b6-85d1-470d-b564-e040aaa0a8b8/ak2-plus_case_120mm_main.jpg)
