Liczymy pasujące modele…
GYRONULL Pick up any spinner you own. Get it going, then turn your wrist. Feel that? The way it pushes back and wants to stay in its own plane? That is gyroscopic torque, and it is the reason a spinner feels alive in your hand. Every…
Remix of a remix :) The original part didn't last a week - the tab on the outer ring broke from fatigue. Here's a redesigned version with a stronger (and simpler) mount. Enjoy! Print instructions Use supports
This is a fidget gyroscope. It spins and doesn't have any pins so you can rotate it in any orientation Notes: The proportions change as the number of rings increases. The smaller the number of rings, the smaller (in height) I made the…
Nuevas versiones del mate giroide. Una version de finas lineas y otra de forma de panal. actualizacion v4.0: nuevo encastre conico
This simple gyroscope fidget prints in about 45min and spins remarkably freely. I usually carry several of these to give away as gifts, and they are some of my most popular prints
This is a modular stand to hold the XSC G600 electronic microscope. I designed this because the original stand was terrible. Use 4 x m5 nuts and 4 x m5x30 bolts with hex head to assemble the stand. Important The arm-1.stl (orange x 2) and…
Tired of your drink tipping over while you're zooming down the sidewalk, weaving through traffic, or just trying to enjoy a cold one on your ride? Meet the Gyroscopic Can Holder. Designed for 22mm handlebars (bikes, scooters, strollers,…
I designed this hook to hang bags on our Mountain Buggy Duet stroller. This is a version with gyroscopic cupholder. To assemble it you need 4 M2.5 screws with nuts and to secure them I use Loctite glue. Hook_with_holder should be printed…
MEMS Gyroscope 100:1 scale model of a MEMS Gyroscope. https://en.wikipedia.org/wiki/Vibrating_structure_gyroscope For demonstration purposes only, but doubles as a nice fidget too :) Printing: Printed in PLA. Print without scaling for a…
This adapter allows you to mount any finite RMS microscope objective (i.e. objectives that are marked with "160mm" rather than "infinity") on your Sony A, Sony E / FE, Canon EF / EF-S, Canon RF, Canon M, Nikon F, Nikon Z, Fujifilm X,…
This is my fourth iteration of the fiendishly clever walking toy invented by my friend John Jameson back in 1981. It mechanically gears a spinning gyroscope (made of 104 pennies!) to a cam which pushes a pair of feet up and down. When one…
DESCRIPCIÓN DEL MODELO 3D Llavero simple con función giroscópica. PARÁMETROS DE IMPRESIÓN 3D Plástico: PLA Soporte: Si Alto de Capa: 0.2 Temperatura Nozzle: 205°c Temperatura Cama: 70°c Relleno: 0%
This is a 100% 3D printed phone holder for microscopes, designed to make capturing images and videos simple and precise. The mount allows smooth adjustment left, right, up, down, and forward and backward relative to the microscope lens,…
Keep your drinks stable and spill-free with this innovative gyroscopic can holder! Designed to attach securely to your belt or pocket, this holder uses gyroscopic principles to maintain your 33cl can in a level position regardless of your…
These are a couple of gyroscope fidget toys I designed and after playing with/testing them I think they are ready to share! Both the disk and cog at 100% are about 80mm in diameter and 24mm tall. 0.4 or 0.6 nozzle, No supports, 3…
En este stl van a encontrar el ya clasico Mate Giroscopio pero esta vez todo cerrado y con un mejor agarre.
I Remixed this for the Extruder as Mini. Press fit a 8mm x 6mm Magnet or I used two 8mm x 3mm Magnets. Enjoy and have FUN! 50 Pcs 8x3mm Neodymium Magnets https://a.co/d/ai8vfr1 The Provided G code uses a filament swap. I have provided the…
A simple but fun Gyroscope Fidget. It is Print in Place and should work after breaking the rings free. Rinse it slightly with water for smoother movement.
A simple but fun Gyroscope Fidget. It is Print in Place and should work after breaking the rings free. Rinse it slightly with water for smoother movement.
When the 4x microscope objective available from “Reakway” is mounted 150mm away from a camera's sensor, it works wonderfully for photography, covering a full-frame image sensor with a nice sharp image. You can find my standard…
13 llaveros que representan cada uno un signo del zodiaco. Dimensiones de 50mmx50mm y diseñado para imprimir a 2 colores.
Check the published mods, you may want some of them right from the start! The improved stage movement is ESPECIALLY recommended :) This project is about an affordable, expandable and customizable microscope based around basic hardware, 3d…
A gyroscope fidget toy. It was printed at 0.2 layer height an 10% infill. It should be able to spin right of the build plate.
This is an another USB microscope adapter for my modular stand. Modular stand: https://www.prusaprinters.org/prints/48589-modular-stand-for-electronic-microscope Designed in FreeCAD 0.17.
A fun little fidget toy gyroscope with each layer showing whole notes, half notes, quarter notes, and eighth notes. I had hoped to use more authentic looking music note graphics, but they involved too many overhangs that would have…
Have you ever thought of combining a bearing, a gyroscope and a gear fidget toy? Probably not, but here it is, and it is a true adventure for both your fingers and your drifting mind. It is easy to print and assemble, and it needs no…
This 3D model is a coffee cup holder that attaches to a stroller, making it a must-have for parents who enjoy a hot drink while on the go. The holder includes several parts that can be 3D printed and assembled with the help of some…
A simple holder for microscope slides. A fast-to-print rack. Do you like it? Please consider to buy me a cup cup of coffee . Thank you! Print Settings Printer Brand: MK3, Prusa i3 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill:…
Gyroscope Fidget toy (keychain) Keychain with ring or without. Printable at the size you prefer. If anyone has any questions please contact me, THop3D
This adapter is based off of the other universal microscope adapters, which didn't use M3 bolts or have the ability to easily set the distance between the eyepiece and the camera. This is my complete redesign. I have also added another…
A small gyroscope fidget toy Print flat, on its side, recommended to use either no adhesion or raft , do NOT use brim! Mines was printed with 0.15 layer heights, 3 walls thick Should take around 30 minutes to print
Being newer to RC flying, I crashed my AeroScout hard enough to fracture the wooden servo & battery tray. It features a built-in lap joint for strength when gluing. I originally tried an existing design by TeslaScorpion , but ended up…
When you take it off it might not be spinning so easily. So just keep playing with it and it’ll spin.I have also made a 5 ring gyroscope https://www.printables.com/model/605104-5-ring-gyroscope-smooth-spinning
All files are in .3mf (because its far superior to .stl). Thingiverse requires a .stl file though, so I added my retraction calibration .stl to the list. Anyways, took ekaggrats .3dm file and heavily remixed it. Solid rack so that print…
Supports required! Edit: I recommend using Tree supports, and utilizing a support blocker between the two toes. This will help make supports not cross between the feet! (see image of support blocker between feet if you need some help.) If…
A simple multi-piece print-in-place heart that rotates within itself. Two versions included, one with an embossed name, and a blank file too. Print instructions Highly recommended to print this with a raft as any elephants foot on the…
Summary: This is a gaming themed modular drink and snack holder. It is perfect for keeping your drink from spilling while on an uneven/level surface, such as a couch, chair, or bed. It includes a storage compartment perfect for holding…
Small disclaimer: Since Dr. Allen Mehr lives in Hawaii and I am currently in germany I had not real laparoscopic instruments at hand and therefore used some wooden rods for my fotos xD Heyho Last year Dr. Allen Mehr asked me to help him…
An elegant and original spiral fidget spinner 3D printed for stress relief! This innovative toy features a spiral structure that spins smoothly around its axis. Perfect for relaxation, focus, and keeping your hands busy, it’s ideal for…
This is a simple little gyroscopic keychain I designed in Fusion 360 following the Product Design Online tutorial as a guide. I took it a step further and set it up as a multi-color MMU print.
Nice little print in place (PIP) keychain fidget toy for all VOLKSWAGEN fans. There are different versions available with different gap widths between the rings. Have fun! Material: PLA Layerheight: 0.2mm Infill: 15%
Heyho Some time ago I published a laparoscopic trainer that can be 3D printed for medical students. The advantage is, that this design is cheap to create, very versatile and portable. Perfect for students!…
Horoscope medallion. Used for a keychain. Not all animals have been included. The models can be printed with 0.4 nozzles and lower.
This mod addresses some useability downsides with the dual M5 screw movement of the standard module. The independent rack and pinion movement for x and y prevents the binding issue of the two interconnected knobs, and the new gears…
I remodeled the original model to make it much more sleeker and use a lot less plastic. there are two slide models . depending on the calibration of the printer one is a bit tighter than the other. you need m2.5 x 6mm x 5 thread inserts…
I scaled the original model and created a stand for it. All axis points are smooth and able to rotate freely.
This mount only requires 1 screw in the ceiling and consists of multiple parts that can be printed flat to optimize layer orientation. I found other RC plane mounts lacking because either their hole spacing required mounting into drywall…
CMF Phone 2 Pro + CASE by Jon Prado Follow me, leave a comment or message me for Design Requests/Add-ons to this project or to collaborate. The inspiration behind the Design is a focus on Self Expression, Modularity and Utility. About the…
It uses 18mm M4 screws and 7mm M4 nuts. I recommend to use nyloc nuts for the outer ring. There are different attachment options, see the original for more details. I added a custom rod which lets me insert the holder into my bicycle…
Gyroscopic cup holder designed to clamp to boats or offroad vehicles and prevent beverages from spilling. The beverage holder is designed to accommodate an average sized can. The hardware used to assemble the initial prototype were 1/4-20…
I've always loved these kinds of spinners, but they can be a nightmare to print. Ball-based bearings are the best for spinning, but printing spheres is an ongoing challenge. So I thought I'd have a go to design something that is easier to…
As you may know, microscope arm is stupidly expensive. So I design this for an alternative, for the pipe I use a cheap monitor arm that has diameter of 30mm. I also design the holder to be compatible with 25mm(1 inch) and 32mm(1 ¼ inch)…
A small box for working with microscope slides. Designed to hold 10 slides (75x26mm) and 10 cover slips (24x24mm). Four receptacles for 13mm dia' vials. Removable dust cover to keep slides clean, and can be used as slide mounting surface.…
New to the 3D printing world and design. I was inspired by others who designed similar fidgets. So i took on the task to design one and test myself. This is what i ended up with. This print is very large and measures 105mm X 46mm and will…
A awesome stressing toy and smooth spinning rings.
I wanted to mount my DSLR to an old Olympus VMT microscope. Found a fitting camera attachment (on ThingiVerse) and made a remix with a fitting cylinder for the microscope. Also made one for a cheap Bresser Microscope (but it doesn't…
3D print your own Transmission Electron Microscope (TEM) ! This model is designed for FDM printing, but probably works okay on SLA printers with some smart placement on the buildplate. ✨ Features : The microscope column opens up to reveal…
project based on research from me (@V_saggiomo) and Benedict Diederich (@beniroquai) *update April 2023 - we are testing external (battery-powered) LED. These LEDs are usually used for decorations, can be on for 2 weeks, and are quite…
For a small Christmas tree Ornament
ACTUALIZACIÓN 3-4-2024: Añado un soporte extra para accesorios (leds, pinzas, etc) donde se pueden roscar dos tornillos de sujección. Hay que usar dos insertos para 3 mm. He diseñado un sencillo soporte ajustable en altura para mi antiguo…
A simple model of a box holding 25 microscopy slides of 76x26 mm. The front is recessed to place a label. The 'Microscopy slide box lid label.pdf' can be used as a label inside the lid of the box.
Just combined 2 projects from here to fit the necesities of my usb microscope, its fully printable, needs no support and added some changes to fit on printer area of 190x190mm, also modified the base to be a little more flat, and smaller.…
I made this gyroscope looking puzzle to enter the Brain Teaser Puzzles contest. You can play with the dimensions (parametric table) but be careful with the width on small diameters because the “key” can be blocked and the puzzle unable to…
Gyroscopic Christmas ornament. You can print each circle in a different color or just like me, change colors on layers :)
Remix of the Extruder Gyroscope Print in place with press fit magnets This gyroscope snap onto the Prusa Mini+ x-axis shaft without any magnets It is made for the Purse Mini+ but should be compatible with the MK3 / MK4 If not, let me know…
Nice little print in place (PIP) keychain fidget toy for all BATMAN fans. There are different versions available with different gap widths between the rings. Have fun! Material: PLA Layerheight: 0.2mm Infill: 15%
I printed the original stand, but it was too wobbly and jank, so I remixed it. Parts needed: 2x M4 countersunk screws L=12-20 mm 4x M3 countersunk screws L=8-12 mm 2x M3 button/socket head screws L=12-20 mm 2x M3 countersunk screws…
Heyho For the MakerFaire in Hannover I did need some tools for the visitors to thest the laparoscopic trainer. https://www.printables.com/model/864261-laparoscopic-trainer-for-students-and-surgeons-col Sadly the tools my friend Allen Mehr…
C/CS Mount Extension Tube (8mm to 65mm) for Microscope, Raspberry Pi HQ Camera, TV Lens, Macro, etc. Print at 0.1mm layer height for best results. No supports needed for printing. May need brim when printing long extension tubes.…
Start by making my 4x microscope adapter for your camera: https://www.printables.com/prints/143754-microscope-adapter-for-4x-macro-photography-with-s Then add this particular 4x objective (only this one is supported) to it:…
The second version of the “matchboscope” https://www.printables.com/model/412753-esp32-microscope-matchboxscope Here we introduce the ESPressoscope, a microscope as big as an espresso cup :) We moved away from the ESP32-Cam and are using…
Ornament= 0.4mm space Ornament2= 0.2mm space Ornament2 no logo= without star 0.2mm space original from https://www.thingiverse.com/thing:207632
Always annoyed by commercial SEM stub holder for four stubs, while I can have five samples in one run. So I decided to design an holder for five SEM stubs (standard stub with a diameter of 3.2mm) The cover fits perfectly on top of it, but…
Enhance Your Lab Organization Effortlessly Perfect for any laboratory, this design is available for free download to help you keep your slides safe, accessible, and well-organized. Key Features Durable and Lightweight: Ensures a robust,…
I remixed this to use M5x20mm button head screws, as I didn't have any M5x30mm bolts. For hardware, you'll need 4 x M5x20mm button head screws and 8 nuts. Be sure to tightly screw one nut onto each M5x20mm screw (adding some Lock-Tight is…
This is a fidget that you can put on your key chain to add some personality, or keep as a standalone toy. It can be easily customized through your choice of the different provided STLs, or even further by using the provided blend file.…
Modello portachiavi a forma di microscopio stilizzato
Andonstar AD407/AD409 soldering microscope mount for Rode PSA 1 microphone boom arm. Re-use the thumbscrews from the original mount to attach this mount to the microscope, then attach to the microphone arm, see photos for my setup. PLA or…
Remixed the remix of another remix ;) I liked the original model a lot, but it got loose and boiled randomly. So I decided to make my own version including a rail to pass a zip tie arround it. Now it doesn't move at all and it's really…
This spinning top prints without support or other special configuration. The three parts can be easy assembled without gluing, simple snap in. And yes, this thing looks like the sign of a German car brand. Print instructions If you like a…
Stackable tray to hold microscope slides on their long edge. My intended purpose was to be able to hold/store slides that have pre-cut tissue controls for easy access during microtomy. There is an area at the front for a label to identify…
Designed to attach on this Canon EF/EF-S Adapter With Screw Holes . The Canon EF/EF-S adapter extends the mechanical tube length (MTL) slightly, and makes the spacing between the Canon sensor and the flange of the microscope objective…
Remix of a remix of a remix :) I draw the socket that fits the MK4 Motor and keeps the gyroscope steady.
This remix includes both the gyroscope and the optical illusion You can print and use them separately or mix and match them to use together The connectors are made for the MINI but i added an adaptor for the MK3 No magnets required Print…
if your lens are heavy, use the type A mount. Use type B if your lens are lightweight. for BOM, LOOK AT THE CAD! I won't provide guide. should be easy to understand. for the lens mount, pinion, rack and knob, get it from the original…
A set of "filters" to be used as 32mm darkfield filters for microscopes Category: Parts
I created this stand to hold my cell phone steady while viewing dates and mint marks on coins, but you can use this for anything you need to zoom in on. The phone tray is sized for an iPhone 14 Pro, but should hold many different brands…
Microscope arms are expensive. What isn't expensive are the multitude of vesa monitor mounts available. I wanted to use a vesa compatible gas spring arm for my Eakins digital microscope. I also wanted the ability to use standard…
This accessory replaces the standard single objective nut with a three positions rotating turret. This way you can "zoom in" or "zoom out" selecting a different magnification objective. Bill of Materials One set of printed parts, printed…
Putting a gcode, but in case: 100% infill .15-.2 resolution Any material should be fine(PLA- 205-210celc) Lower print speeds(PLA- 40-50mm/s) Supports on plate only upside down If you enjoy my work, don't forget to like!
I recommend using PLA for this print and use a 0,2 layerheight. This print doesn't need any supports. Happy printing
Gioco progettato per il concorso di design Fidget Toys Stampa sul posto Piedistalli con doppia funzione, per appoggiarlo sulla scrivania e per tenerlo fermo mentre si gioca Cornice esterna con piedistalli, tre cerchi e una sfera centrale.…
Made for my Mini+. I found that magnets want to stick to the edges of the opening instead of the spinning part in the middle. I noticed the top of my Z axis rod had a small 2mm hole in the center of it so I modified this to press into…
Revision 0.6 - RMS male better toleranced, Z axis up, add height and logo, added M25 This is a set of parfocal extenders and adapters for microscope objectives. 1) They have RMS thread, both male and female. It is also called "DIN"…
This remix includes both the gyroscope and the optical illusion. You can print and use them separately or mix and match them to use together The x-axis connectors are made for the Prusa Mini+ but should be compatible with the Prusa MK3.…
Awhile back I acquired a digital microscope and found the default base that came with it incredibly useless. I had acquired the microscope after reclaiming some one GameBoy Colour games from my childhood home, and needed to do some…
Vytištěno z materiálu PLA, výška vrstvy 0,25 mm. Pro zuby hřebenu, pastorek a osu výška vrstvy 0,15 mm. Matice přilepit do jednotlivých dílců dle výkresu. Výkres sestavy stojanu (výkres ve formátu pdf uložený v souborech): Typ mikroskopu…
You can find all other parts at the original project: https://www.printables.com/model/48589-modular-stand-for-electronic-microscope
