Liczymy pasujące modele…
This small piece allows hardware mounting of your ESC switch at a convenient point in the back of the chassis, where you can turn the car on/off without taking the body off. It uses the stock motor wire clamp screw location and fits right…
This simple print can replace the factory sway bar links for the Team Associated Pro4 SC10 (and Rival MT10). I found the factory links tend to fall off pretty easily, especially on the rear. Unfortunately, you can't buy just the links…
This is 3D-printable parts of the enclosure of the SC1000 by Rasteri. The SC1000 is an open source digital scratch controller. 3D-files and renderings made by me. I recommend not to order these files from a service or go through too much…
This is replacement to aluminum bearing block. I used these on heated bed movement, with printed blocks you can reduce 160 grams of moving mass. Bolt grid matches on Reprap Trespa carriage plate sod here:…
This front bumper support for the Team Associated Pro4 SC10 is a rugged replacement for the stock piece that has broken several times on me. As usual, Team Associated doesn't offer this part alone, and only comes with the entire front…
After being unable to locate the battery strap for my Team Associated SC10 RC Truck, I took measurements of the chassis and designed this replacement. The truck has long since been discontinued and I'm unsure if this same part will fit…
Hello, I needed SC10UU with SC8UU holes dimensions, so I created one. You have 3 versions. My original and then lighter and smaller types. Also I created SC10UU with original dimensions. It is also available in 3 versions.
This is a mounting base to allow an MSC10 Garmin Satellite antenna to mount where a prior Garmin GPS24XD was located. The three holes are similarly spaced, but this allows adjustment if the hole orientation on the boat isn't appropriate…
A stock Team Associated Pro4 SC10 does not have a good way to secure ‘shorty’ 2S LiPo batteries, which are popular for racing and come in much higher C ratings than the standard basher style batteries. So I designed these adapters to use…
This design protects the tail light LEDs on the Team Associated Pro4 SC10. The truck comes stock with the LED leads bent at 90 degrees and wires tied tightly to the bumper assembly, which makes them prone to damage. There is no slop in…
This piece acts as a spacer to sit on top of a 2S LiPo battery to make it the same thickness as a 3S battery, such that you can use the same length straps with both battery sizes. The spacer has built-in ‘shoulders’ that are spaced apart…
Original design by Burak Ozcan.
Now that saddle packs are history. Time to go back to the original strap for standard size packs. But wait, what do you mean you lost the original parts? They are not manufactured anymore? Can't find them anywhere? Worry not. Here they…
This allows you to raise the outer camber link by 8mm on a Team Associated SC10 4x4 RC truck Instructions Print at high density, and install on the rear hubs. Category: R/C Vehicles
These simple pieces allow you to use carbon fiber battery hold-down ‘tabs’ in the Team Associated Pro4 SC10 for ‘shorty’ style batteries, like these tabs for the TLR 22x4 4WD buggy : The pieces have a single hole each for a countersunk…
A battery wall (without ESC tray version) to go along with your standard pack lipo battery. Original design by Burak Ozcan
A nice simple 1x5 Gridfinity bin for a Noga SC1000 scraper, can accept 6x2 magnets on the bottom. Its a pretty simple print that should work on almost any printer. Thanks for looking and happy printing!
A nice simple 1x5 Gridfinity bin for a Noga SC1000 scraper, can accept 6x2 magnets on the bottom. Its a pretty simple print that should work on almost any printer. Thanks for looking and happy printing!
This small piece allows hardware mounting of your ESC switch at a convenient point in the back of the chassis, where you can turn the car on/off without taking the body off. It uses the stock motor wire clamp screw location and fits right…
This piece acts as a spacer to sit on top of a 2S LiPo battery to make it the same thickness as a 3S battery, such that you can use the same length straps with both battery sizes. The spacer has built-in ‘shoulders’ that are spaced apart…
I remodeled my original one whose material fatigue-cracked after 5 years of usage. If you print it with FDM then I recommend the model to print in the position shown in the pics: the side-walls around the magnet are pretty thin, you need…
The Team Associated Pro4 SC10 has a couple of issues around the front headlights, one being that the body pops up and on top of them during crashes, and the other being the excessive brightness of the LEDs when looking directly at them.…
