417 modeli
I love the look of these shelves, check how Tom created them: However, I wasn't a fan of the uneven and paper-thin back (even though I believe mechanically it doesn't matter). So I've made it completely flat and a bit thicker. I also went…
Wydruk około 7,17 €–8,76 € nettoWstępna wycena jednego wariantu
The bottom in the original pot can be a little flimsy, being only 1mm thick. It gets even thinner when you scale the model down, so in this version I made it roughly two times thicker. Otherwise it is identical to the original.
Wydruk około 4,67 €–5,71 € nettoWstępna wycena jednego wariantu
This is a remix of John's card to put under the kickstand when parking on soft ground. As per original description: “If you lose or forget it, you can just print another one.” As the original was too thin, I created a thicker one. While I…
Wydruk około 1,36 €–1,66 € nettoWstępna wycena jednego wariantu
I wanted a handle with a similar form factor as a condenser microphone, so I could use it with a traditional microphone arm, or to handle it myself while talking to the camera. So I went and remixed one of the models by @365Prints…
Wydruk około 2,03 €–2,49 € nettoWstępna wycena jednego wariantu
A stand made for ~20 cm height FumoFumo plushies by Gift. This stand was made with sizing referencing the standard FumoFumo Koishi Komeiji plush. This stand fits loose, and is only meant to keep the plush upright on a stable flat surface.…
Wydruk około 1,22 €–1,49 € nettoWstępna wycena jednego wariantu
I increased the clip dimensions to allow for the thicker edge that I wanted it to slide onto in my Mustang Mach e. I also designed a slide on cover for aesthetic reasons. I printed the bin with a .6 nozzle to shorten time to print, but…
Wydruk około 2,33 €–2,85 € nettoWstępna wycena dla PETGMateriał u źródła: PET
These side brackets are for my Venezuelan red tail boa to have something to climb on in her tote! I use bamboo for Snips to climb on so far so good. .30-layer height and 150% print speed. I used a solder iron to burn holes through the tub…
Wydruk około 2,26 €–2,76 € nettoWstępna wycena jednego wariantu
Also check out this chamber reinforcement :) Print settings material: PETG, also enable brim for the lid only and set to brim_width=10mm, brim_type=inner+outer lid : 9 perimeters (to make it 100% solid along the top sloped part) lid's lid…
Wydruk około 10,39 €–12,70 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Modified blade to be thicker With the original blade model, the blade pieces kept breaking whenever I swish-flicked it open because of how thin the walls were, both in PLA and PETG. So I increased the width of the walls of the blade…
This is a remixed/edited phone stand that I configured to use at my desk for my iPhone XR that has a thick case on it - the original just fit the bare phone without a case. Widened the body a little too for support. Printed on my prusa…
I have received a lot of backlash on Reddit, calling this "gooning content", so before anyone calls this “gooning content,” please consider this: X: We must respect women and their bodies! X: You drew a woman with large breasts, you don't…
Keep Your Filament Tidy – Now Stronger Than Ever (V2) An improved, compact, and user-friendly clip designed to secure filament ends on spools—preventing unwinding and tangling. Now in Version 2 , featuring thicker walls for enhanced…
I like the design of the original caliper mount, but I managed to snap a supporting vane off mine while removing it from the print bed. I remixed that model to thicken those vanes slightly, and now I have no troubles printing robust…
This is remix of https://www.thingiverse.com/thing:4596529 by thomasotwo@thingiverse I wanted those mountains higher and thicker. So I modified it in Blender to make it thicker and then I scale its height to 133% (10mm). It's still fits…
First layer at 0.20 Print rest at 0.15
Someone in the comments mentioned that original canopy is too thin for TPU so I added 0.5mm thickness for it
This is a quick remix of the Prusa provided spool holder (B4). Added an extra 10mm thickness to the overall width of the original design to add more rigidity. The clip on portion also benefits from an additional 10 mm to snap onto the…
i put both halves of the coin together, added a middle layer, reduced the depth of the minting and added a stand. Print upright with copperfill, age it with vinegar or ammonia. have fun! ++ UPDATE ++ Added one with no stand for custom…
Having long hair has its challenges, it often does not behave and makes frequent escape bids from hair elastics. I wanted to find an easy hair clip that can control thicker hair without applying any tension which might cause headaches…
I took Matt Germans beautiful Lord's Prayer art (https://www.printables.com/model/711044-ourfather-cross), added Jerry Lee's extended tabs (https://www.printables.com/model/722193-lords-prayer-cross-hanging-wall-art) and shortened them…
This is a remix of the model by Derailed3D. Schnipp already did a remix with a thicker tail as well, but I changed the shape of the final bump a little so you can decide between the two which you like best. Please disregard the different…
(Thicker) Mini Shoe Horn with HONEYCOMB Cut-Out | REMIX Made a HONEYCOMB Cut-Out remix from the great original model and added a hole/honeycomb version for the thicker version of the shoe horn as well, the original hole was a bit too…
Original Qidi filament adapter given to me from Qidi. I have posted the original and a simplified version I have created with a much lower file size. Both files create the same adapter. These work great for leveling the bed, so keep an…
Slight modification to make the walls thicker to make it more durable when printed using ABS. Scale to your needs.
Version with a thicker border so it isn't so flimsy, modified connection points for easier parts removal, rounded corners of catapult arm for comfort, reinforced pivot pins, condensed assembly guide to two pages per sheet.
Wings are now more than one layer thick, more durable. BEND THE TAIL TIPS UP AND ADJUST THE ELEVATORS.
This remix adds a bit more material around the bolts for the hinges and latches so that they are less prone to breaking when adding the M3 bolts. I used the original 4mm latch. I printed the case in PLA and the hinges in PETG. You will…
Headphone holder like the source model, but with a large enough mount to fit on thicker desks. Made to fit on a butcher-block counter slab standing desk conversion.
I seem to have not very good orange PETG filament and when I tried to attach the legs to the body, the thin legs always used to break. I printed many legs on Ender3V2 and broke them all. Finally I've contacted reddadsteve and he suggested…
Remix of Jaatinen's Safety glasses holder for the honeycomb wall storage. Made to be capable of holding thicker glasses
I really like the original model, but the roof of the pacman mouth was very thin and it delaminated, so I designed it from scratch trying to be as precise as possible with the original model, fixing the mouth roof. This is my first model…
Keep Your Filament Tidy – Now Stronger Than Ever (V4) An improved, compact, and user-friendly clip designed to secure filament ends on spools—preventing unwinding and tangling. Now in Version 4 , featuring thicker tip. Ideal for storage,…
Loved the original by Bieraugel but really wanted a thicker base and the logo. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: .12mm Filament: Inland PLA+ black and white Notes: Did a…
Prusa's original y-rod-holder has a very thin section above the y-rod, which is prone to breaking if over-tightened. Furthermore, if printed in ABS, the top may show unsightly stress marks after tightening, even if it is not…
Same as original remix but for spools with thicker walls (thanks to WhatWouldAnEngineerDo for pointing out that cardboard spools are a bit thicker). The first remix is at:…
After a month of growth update V2 -realized that wall are too thin and Sun gets to roots. Walls thickened by 22%, recommend to print with 5 loops for essentially 100% infill. For V1, using black spray paint to do two coats of inside fixes…
I've been printing this lovely little trilobite with a 0.6mm nozzle and I've noticed that with any small extrusion error the vertical sections of the links appeared quite thin. So, I thickened the links a little to make sure there…
Multiboard plier holder for my kingcrome pliers which are 22mm thick at the handle. It just utilises the snap fitting. I printed mine in esun PETG on my Elegoo Centauri Carbon sliced in the Elegoo Slicer with stock settings. I decided to…
I got tired of trying to print this in ABS without the deck plate splitting, so i thickened it 2mm and added 1mm x 2mm strakes to the sideplates. You may need to round the corner of the slider feet to clear the strakes. If they don't work…
Edit: Today I wanted a thicker moon, these first ones are quite flat, nothing matter with that and I perfectly love them still, but some days you just need more moon. So, there's those new .stl's that are, hmm, various and two of them are…
i just custom the perfect stl from Boogie I just add a few millimeters to the honeycomb pattern in order to make a nicer color change. I added supports only in the center for a perfect rendering. Use a M3x8 screw That's all !
A quick and dirty remix of the adjustable Endstop Trigger for the Anycubic Vyper by Einlander, I made in Blender. Basically, I just made the body thicker, so it can be used with the original screws. Also, I doubled the thickness of the…
Support me: Post a Make and Comment PayPal Venmo: @paulorfo Cash App: $paulorfo ------------------------------------------- I printed this incredible foldable bow, only to have it tear apart during the folding process. Recognizing the…
slightly thicker version to improve stability
I felt that the original knobs were too thin and difficult to turn, so I remixed them to increase their thickness for easier gripping and turning. By designing the knobs to match the style of the Tensioner Knob and Display Knob, it also…
I love that extruder guide, it's one of the first upgrades I've printed and installed on my machine. After few months the base is now deformed in the thinner side, (said I've printed it in PLA+), so I've thickened it, and also made two…
I noticed that my phone would overheat if I set something on-top of it while charging, and the lack of places to put things bothered me anyway. I designed this shelf so that my phone fits underneath it, and I can set stuff on the upper…
Combined x-1 and x-2 files, then scaled Z thickness to 2mm and z thickness of outline to 2mm also for more dimension and to make sturdy Croc charms.
Change log: V4 (1/10/24) - Update hinges
Updated April 24, 2026 What's new More durability with thicker walls (2 walls) Completely redesigned geometry for cleaner file Updated lid now matches the shape of the container Printing Tips 3 Walls Save filament: 0 Top/bottom layers 0…
I printed the rugged case for my TS100 (https://www.printables.com/model/345083-rugged-multipart-pinecilts100ts80-case-v2) and noticed, that the stand for the soldering iron would not snap securely into the top of the case. Also the…
Improved thicker mounting bracket, to avoid breaking
I liked the original model for its minimal look, but the clip snapped off after printing it. I remix it with a stronger clip after snapping the original. I make sure to do the remix to be printed with no support. It turned out alright…
THIS HAS NOT BEEN TESTED ON A HUMAN PLEASE REVIEW THE SOURCE INFORMATION AND DISCUSSION THREADS REGARDING THESE SORT OF DEVICES. I used Andrew's original model to create this variation. It should result in a stronger splitter for those of…
The standard hooks only work for very small bike racks with thin tubes. a lot of ebikes have thicker ones. Aparrently you cannot buy them in other sizes. So I made a model. The small one can also be used to replace the original, even if…
Remix of the awesome desiccant box from @chrisd with just a bit thicker (1mm) lid and base.
Adaptation of Rubomake's fan adapter, with thicker walls so that it's suitable for print in larger nozzle sizes and more durable. Category: 3D Printer Parts
After I broke the original ones, I designed thicker springs for this Heat Insert Press . It needs M3 X 15 mm minimum lenght bolts. I printed them on PETG with many perimeters.
I made both parts a bit thicker around the thread for better strength and to hide the thread when printed. Every time I printed it, thread was visible. In this edit it is hidden when printed.
This is a remix of a bottom part of the Dragon Egg to make it slightly thicker.
the original was too tall and did not fit my ender 3 pro, so here is one with better clearance so it does. there is also more space in the case to accommodate for any y axis belt tensioner mods. my last issue with the original one was…
Had a work phone with an Otterbox cover so needed to extend the lip to allow for a thicker phone.
Hi, if you open the .m3f file in Prusa Slicer, you will get the original design and two cylinders. Current setting is that internal diameter is 114mm. The negative-volume cylinder defines internal dimensions. If you scale it, ensure it…
The original model is GORGEOUS. Very well made. However I feel like it works better as art. In my own case, my child wants this, so printed it. While removing supports one of the wings split on the weakest part, so I decided to make the…
this is a remix of “Dice Tray V2 for Contemporary Dice Tower/Storage”. I made the model thicker and removed the sharp edges. Because it is now thicker and heavier it also can be used as a standard dice tray without the tower. The small…
This reduce the chance of snow building up around the charging plug. Printed mine in PETG-CF.
I just made some adjustments over Thing 191652. This one is thicker and has a flat bottom. So it should be easier to print. Category: Sculptures
I printed the record coasters and the holder, but noticed that te coaster holder broke easily. So I designed one with thicker walls and deeper cutouts, so you can take the coasters out easily. This originally can hold 8 coasters, but you…
+Improved ventilation (vs no stand) +Still can store some stuff under laptop (with other stands you get improved ventilation, but you are still losing the space under it) +Front hooks should ensure that it will work with most models…
This is a 3D model of an iPhone and Apple Watch stand remix that is based on an existing model made by Daniel. It is a simple and elegant way to organize and charge your devices. It has a flat and thicker bottom for better stability and…
Honeycomb storage wall with thicker outer walls for all printers with a print bed of at least 215x203mm.
I personally have it at 101 mm/4 in long axis, 51.5 mm/2 ish in wide and 3.6 mm/.14 in tall
BOM: 2x D2F-L switches 4x M2x10 screws (I use self-tapping to thread easily into the plastic) 1x PC4-M4 fitting 1x PC4 fitting (I think any size thread will work because the thread isn't used, but I'm using an M10 one) PC4 clip Whatever…
to be attacher with 3M VHB 5952 1" double sided tape
Big buildplate holder for wider slots for glas, carbon and PEX/dual sided PEI buildplates: 2x glas (thickness of the buildplate: 3,5mm - slotwidth 4,5mm) 2x carbon (thickness of the buildplate: 2,8mm → slotwidth 3,8mm) 10x PEX/dsPEI…
Visar78 did an excellent job with the organizer for the Gaia Project! However, editions around the world can present differences, and this was the case with the Brazilian edition from publisher Grok, whose tiles for the "The Lost Fleet"…
I printed mine with (Prusament Signal White) PETG and 30% infill, except of the shell, which I set to 4 perimeter walls (which makes most of the cup solid). !!! NOTE !!!: The Holder Shell is tapered on one side. This side is meant to be…
The original snaps are quite flexible and not stable enough to be fixed with a single screw. This version has a much stronger bridge, providing enough rigidity to mount it securely with just one screw in the middle. Print settings: No…
These trays are a sturdier version of the original with more sizes and larger grid options.
I liked this design, but felt the ring would not be sturdy enough. So I made it thicker. Without the original design, I just modified it in the slicer. With PrusaSlicer, I added a torus as a part and adjusted size and placement.
This is a remix of Antilop Footrest from Tom Ewig but with thicker tabs. The original fastener works.
So I searched for a fitting wallmount for my Xbox One S controller and I couldn´t find one which allows me to mount my controller, because I am using a battery pack which is slightly thicker than the original cover. I am using the MoKo…
just a litle bit stronger version Added version with smaller angle. Print instructions Print with 0.3 or O.2 layer heigth from PETG. Carefully remove from bed.
Migrating from thingiverse https://www.thingiverse.com/thing:4362267 Remix the large one to be able to hold thicker devices, especially the ones with a case on. Original here https://www.thingiverse.com/thing:3146835 gap for the devices…
Thanks to @ArtDesign for realizing it's absolutely essential to protect the Snapmaker U1 electronics compartment (PCB) from the heat of the printer chamber, especially if you plan to enclose your Snapmaker U1 with a TopHat or Lid and…
My sister rescued a guitar from a trash heap in the rain one day, a Yamaha FG-335 from the 70's. Surprisingly, it was in very good condition-except that it was missing a string and a bridge pin. I printed a few bridge pins from this site…
You can print this on PLA but I printed it on ABS and ASA. I printed with the following settings: wall loops: 4 bottom layer: 5 layer height= 0.2mm Infill 40% for strength with Adaptive Cubic pattern
This model is a remix of the charging handle by N8than (loose tolerance version; which is still nice and snug, as the original was incredibly tight). The only change here is a thicker top shell for added rigidity, since the original was…
This is a remix from https://www.thingiverse.com/thing:2737639 I remixed the small and large antiroll version of the original. It fit's for my Google Pixel 7 Pro including bumper. Supports should be used.
All of these pieces were printed with TPU 95A, 0.28 layers, 25% grid infill, 2.5 mm3 flow, 240C nozzle, and 140F dryer. TPU can stand the torque of firm twisting into place, but the flimsier pieces (eg, slotted guides), need more work and…
Simple Laptop stand for laptops with 22mm thick base.
Made the shell 5mm wide to prevent the thin shell from warping, should also improve the sound quality by dampening influence from the back. There was a variable in the original CAD file for this, but the file needed some additional…
A thicker version of my previous phone stand for thicker covers.
Original had a couple walls too thin for 0.4, ended up as a hole. This remix is thicker
To print the canopy, print it vertically with the nose on your bed. I used slim tree supports and it worked out very well. For info, I printed the canopy at 0.16mm layer height and the grommets at 0.2mm layer height. Use 3 perimeters or…
This filament holder is multifunctional. You can use it for a cardboard spool but also for a small one I hope it will help you I must say that I have not yet tested the nut and pin, but I have tested the spool holder this is especially…
Increased thickness of focus to wheel to 3mm to make it feel less flimsy. Note: the faceplates are not modified but only included for completeness. Print instructions Category: Camera
Simply added an extra mm to the bottom base so it's not only 2 layers thick by the tray.
This is my remix of Maple Leaf Makers Modesty Mesh for my Voron V0. The two key changes I've made are: It has a thicker border to them from bowing once installed. The clips are offset to allow running wires between the chamber and the…
I was asked if I could print out a base for a Triton TRA001 router but "two or three times thicker" This one is 6mm thick Remixed from a model found on thingiverse
![Rode Wireless Go Handle - Shorter and Thicker (Condenser Mic Form Factor) [remix]](https://media.printables.com/media/prints/708849/images/5560717_ae14a831-061b-4090-9d33-a60d35514964_04cd4bb4-c195-4a5b-b810-5629f3b2daa1/perspective.png)
![Honeycomb thicker outer walls [215x203]](https://media.printables.com/media/prints/580575/images/4635119_1ad4682c-bfab-4777-9b72-abd9570be0cb/honeycomb-walls.png)
