47 modeli
Dieser Halter kann genutzt werden um den Deckel eine Thermo**x direkt an dem Gerät zu befestigen währen man ihn mit Zutaten füttert. You can fix the Lid of an Thermo**x direktly on the Maschine while you add some incredians. 2024-01-03…
I lost the litte handle cover, so i made my own. Should also fit on the TM6.
Made this for my wife, since the original tool from Vorwerk costs €14.- and this part is just a few cents. Since I printed it for her, she's using it almost every time when she uses her Thermomix. Printed in PETG (Prusament Anthracite)…
Give me a Like 💗 Follow Me 😁🤗 40mm Bosch-Siemens = 5mm Hole 40mm Universal Slot Short = 5mm Slot 14mm Deep Universal Slot long = 5mm Slot 28mm Deep Features: The Vertical position is better to clean it. Very neat and organized. Compatible…
very useful to unload pastry of the mix-pot, simply attached to the blade and turn…. ----------------------------------------------------------------- sehr nützlich um Teig aus dem Mixtopf zu entnehmen, einfach unten auf den Antrieb…
Mit diesen Verkleinerer fliegt nichts mehr im Mixtopf herum und man erspart sich das runterschieben mittels Spachtel. UPDATE (11.11.23): Habe eine neue niedrigere Version hochgeladen, da bei der alten der Deckel nicht genau drauf passte.
Spritzschutz für den Thermomix TM5 oder TM6. Kann als Alternative zum Garkörbchen verwendet werden. Sollte in einem hitzebeständigen / lebensmittelechten Material (z.B. PETG) gedruckt werden. Ich habe den Spritzschutz mit 80% Füllung…
Teigblume for easier dough removal on the Vorwerk Thermomix TM5. Not a original part from Vorwerk. For the Print i used the following settings: Filament: PLA, PETG Layerheight: 0.2mm Walls: 1.2mm Infill: 20%
Version 2 now avalible! Updated version has some improvements: the handle hook has been replaced to make it easier to remove the basket from the Thermomix the wall thickness was changed from 2mm to 1mm to improve cooking a larger hole in…
My Thermomix "Teigretter" helps for easier dough removal on the Vorwerk Thermomix TM5/TM6. It is loosely based on the “Teigling” model made by DonBorste but completely drawn by myself - see…
The part comes in contact with food, please use food-safe plastic.
Makita DTM52 wall-mount with added screw holes.
Designed for Makpac size 2 (155mm height outside) Designed in Onshape https://cad.onshape.com/documents/6c8885acbded4393660dad2f/w/ced976dd821b423d755077ca/e/378dd070d238d2d2863483a9?renderMode=0&uiState=63b16e8f08d58430adbfa920
Deutsch Thermomix TM5 – Ersatz-Ritzel V4 für Fehler C142 (Extramassiv & Integrierte Stützen) Dies ist die Version 4 meines Ersatz-Ritzels zur Behebung des bekannten Fehlercodes C142 beim Thermomix TM5. Nachdem mir frühere Iterationen…
2 objects to be printed here - a funnel and an egg splitter that both fit in the hole of the Thermomix cover. I designed them for the TM6 but the hole size is the same so they should also work for TM5. Use FOOD SAFE filament- PETG for…
I printed it with 20% Density and 3 Perimeters. I think 10% Density is also good. 06.07.2019: added this also for gluei
Please print with atleast 80% infill and use proper M4 screws to mount the pieces into the wall or into a wall cupboard. I recommend PETG. M4 screws are used for every one of the three seperate parts.
Mit dieser Drehhilfe könnt ihr das Messer vom TM5/TM6 drehen um z.B. Teig leichter zu entfernen.
Clip on Lid Holder for Thermomix TM5/TM6. Holds the lid in such a position that residue drips back in the pot. Printing: PLA 0.25 Structural Profile with 100% Infill
A dust extraction nozzle for Makita multitool (DTM50Z). Has the same size outlet pipe as their 18V router, or the other dust extraction nozzle I've made. Best to print in something like Nylon/CF I think. Messy design I'm afraid, but I…
Sehr nützlich um den Schmetterling aus dem Mixtopf zu entnehmen, einfach unten auf den Antrieb stecken und drehen. Der Schmetterling lässt sich so ganz einfach entfernen. Auch Teig lässt sich so gut vom Boden lösen. No Support: TM 5&6…
The Vorwerk Thermomix TM5 suffers from a terrible design flaw of its three weight sensors (=WS). These can shift or break out entirely from their internal mount causing the weight sensor(s) to malfunction (e.g. display remains at “Max” or…
My wife wants a splash guard for the Thermomix. So I design this model. The challenge was, to design it printable. So I made the handles as extra parts, which have to be inserted into the splash guard. It's designed with zero tolerance,…
The mixing bowls of TM5, TM6 and TM7 are very similar, yet all share one common and really annoying problem… …as soon as you remove the cutting knife, the bowl will tilt, which is really annoying when you put the bowl in the sink for…
Der Messerdreher macht das Drehen der Messerschraube besonders einfach – perfekt zum Lösen von Teigen aus dem Mixtopf. Einfach den Twister von außen auf die Messerschraube setzen und drehen, bis der Teig herausfällt. ✔ Einfache Handhabung…
Thermomix Dough Tool - 1x for TM31 / 1x for TM5/TM6
This is a replica of Tektronix part number 214-1593-02 which is no longer available. This barrier key snaps onto the EDAC card edge connector that is used in TM500 series power supplies. It prevents incompatible plugins from being…
Extended the neck of the drum by 55mm. This works with the SBF and SBL2.0, and does fit with a bit of persuasion into the FDL not sure what other blasters this will work with. If you test it in your blaster, could you comment down below…
This is a sliding board for the Thermomix TM6. May work with the TM5 - I don't have one so couldn't verify. Requires a 300x300 bed! Print 1 board, 3 feet, 4 rollers and 2 connectors. PETG works for the board. PLA not recommended, may sag…
I dont have the oppurtunity to put screws in my kitchen wall, so i remixed the original design to be able to glue it onto my wall. Category: Kitchen & Dining
This is a simple but effective splash guard for the Thermomix. printed with adaptive layer height for quicker and better results. it uses a modifier to remove the top and bottom layer and Gyroid infill at 20% to create a filter, releases…
Simple wall mount for Makita DTM52 multitool. Not earthquake proof, but keeps it in place on the wall. Plumb walls recommended. Printed in Elegoo PLA+, 0.2 mm layer height, 2 wall loops, 15% infill.
just closed the drilling holes because i dont want to drill in my Splashguard. Used Nano Sticking Tape to stick it to the Splashguard. Sticks like bomb.
OsVac M32 Vacuum adapter for the sander expansion of the Makita DTM 52 Multitool. Printing recommendation: With support material (tree type), only on the print bed
Laser-cut insulator panel and 3d printed brackets for TM501 power supply based on the existing design by NFM.
This replaces the mechanism of a tm500 door handle for RV cargo handle measuring 5" by 4.5". (Might fit others too) Original part are 3 white prongs with snap in/friction connection. I couldn't find the replacement part alone nor a seller…
Spritzschutz für den Thermomix. Passt in den Verschluss zum Aufbewahren. Gedruckt in PCCF mit 0,15mm Balanced Profile. Um 90 Grad gedreht drucken damit mehr Stabilität gegeben ist.
skinny holder for a tektronix plug (AM503 current amp is what I use it with, but any TM500 module ( http://www.barrytech.com/tektronix/tektm500/tektm500.html ) should work. I don't have the tektronix power supply where this TM500 plugs go…
A bookend with three slots for TM5 recipe chips. I added an angled version as well with slightly loser tolerances.
The Tektronix TM500 is a modular test equipment system offering a variety of plug-in modules that fit a dedicated series of mainframes with one to six module slots. This is a blank panel cover for one of its 6 open bays. The inset on the…
kleines und großes MAKPAC-Inlay für Makita DTM52 zur sicheren Aufbewahrung von Zubehör. gedruckt in Sunlu PETG Schwarz
If you want to wash your Thermomix Motor with Alcohol. For repairing of course.
Hi folks , i saw on the internet ,they sell for 10 euro these sliders . in bad 3d print and ect. i had furniture sliders found for 1 euro in the cheap shop. 25mm round and 6mm high. so i made my own , it cost in total 2 euro, design time…
maybe a single stand will follow Category: Kitchen & Dining
Hallo , dies ist für denn thermomix TM5, TM5-Flexy-Abssauger ,ist denn Name , es ist Befestigt durch magnete, alle plastic-teilen kann mann ausdrucken . die teilen die an denn TM5 kommen aus ABS Machen ,weil da wärme kommt . und…
Deutsch Thermomix TM5 – Ersatz-Ritzel V4 für Fehler C142 (Extramassiv & Integrierte Stützen) Dies ist die Version 4 meines Ersatz-Ritzels zur Behebung des bekannten Fehlercodes C142 beim Thermomix TM5. Nachdem mir frühere Iterationen…
Spritzschutz für den Thermomix. Passt in den Verschluss zum Aufbewahren. Gedruckt in PCCF mit 0,15mm Balanced Profile. Um 90 Grad gedreht drucken damit mehr Stabilität gegeben ist.
