Liczymy pasujące modele…
a JIG inspired from the already not available JIG SV 45 from Tormek, as they replaced it by the new KJ-45 JIG, proposing a better centering of the knife and as a consequence a symetric angle of sharpening for both sides. However, offering…
A remix of the drip tray for Tormek T8, but customized for using with the FVB attached. Made 2 versions of it, one that is optimized for PETG and one for PLA - difference being the diameter of the holes that clamps ontop of the rods from…
Tormek T-4 Rotating Base Tormek sells a rotating base for their sharpening system for $70, which I guess is reasonable if I had any money left over after buying all the damn accessories for this thing. Couldn't figure out how to print…
Printing: Main Gouge Clamping Body - 40% infill or higher, print on flat backside Lower Hinge Post and Assembly - 75% infill, 10mm brim, print vertically Main Clamping Body - 40% infill Horizontal Base - 20% infill Follow JL Designs…
A ruler to adjust USB height to Grinding wheel. Instructions for use: Put it between grinding wheel and housing, the small part against the spacer, letters against the wheel, adjust to preferred height. Done! The advantage of having the…
You need a M6 bolt for this knob! Note: If the handle is used for a original Tormek sleeve, an ~M6x9 V2A screw is required If you use it with my own designed Plastik sleeve, an M6x12 V2A screw is required My sleeve:…
My "pointer" was damaged by the grinding wheel. So it wasn´t very accurate any longer. So I printed this spare part and it works as intended :) You need a short 4mm rod as axis. Simply take a wooden rod or brass like i did. Print Settings…
This is my own design of a leather honing wheel. If you have the Tormek T8/T7 drive wheel it will fit. You can Upgrade your old SA-250 or Supergrind 2000 Versions with the original T8/T7 drive wheel as well! Alternative you can drill out…
Small and simple grindstone holders for Tormek stones. There are 3 different versions: 250mm: high: 140x120x30 mm 94g / 20% low: 139.4x110x25 mm 79g / 20% 200mm: low: 120x100x25 mm 59g / 20% The original version is the high profile…
spacer for tormek (all models) tipicaly used for woodturning
This is a simple jig to enable sharpening of router plane blades using the Tormek sharpening system. I also offer some other jigs for hand sharpening of router plane blades . It's designed for cutters that have a square cross section that…
Note that this is for skewed chisels (as used by woodworkers for cleaning out dovetail sockets etc), not skew chisels (as used by woodturners). Skewed chisels ( like these ones ) have a single bevel at a steep angle and make it much…
The original SVA-170 from Tormek is great for hatchets and small axes, but doesn't allow for bigger axes and splitting mauls. That's what this is for The photo shows a comparison between the SVA-170 and the first iteration of the model
This is a set of mounting brackets so you can hangs the DBS-22 Drill Bit Sharpening jig from the wall There are 3 parts One for the base plate One for the drill holder One for the magnifier
I created a drip tray for my Tormek T-4. This collects water that drops off the blade onto the top of the machine and drops it back into the stone wheel water tray below. I made the model to be printed with no supports. I made this with…
Tormek T8 Knife Sharpening Jig - 15° Angle with Magnetic Holder Description Upgrade your Tormek T8 setup with our precision-engineered Knife Sharpening Jig. Designed for a consistent 15-degree angle, this jig ensures razor-sharp edges for…
A replacement knob for the Tormek sharpener knife holders. This is a bit thicker than the original with a little bit larger support base. The threads for the lock screw are printed but needed a bit cleaning up with a tap for the screw to…
This jig can be used to measure projection length when working with the calculator method on a Tormek or similar grinding machine. Example calculator: https://connect.calcapp.net/?app=3fp8xu#/ The jig is designed to work with the Tormek…
Sur une affuteuse Tormek, il faut bloquer l'axe pour utiliser le disque de démorfilage sans la meule (par exemple si elle gène). Pour cela, Tormek fournit un bout de tube facile à perdre… Cette entretoise est sur mesure pour les Tormek T7…
Comment transporter un système d'affutage Tormek T-8 dans un Systainer de Festool ? L'affuteuse n'est pas vraiment faite pour être transportée (15 Kg), et n'est pas un outil Festool. Et pourtant, ça rentre. C'est très juste, mais ça…
Distances made for use with TormekCalc, (by Jan, JVH on Tormek Forum) I made 4 of them, 30, 50, 75, 100 mm in length. If you want to print them with numbers, use split to parts and assign colors, or use as is if you print them solid one…
Leather Honing Wheel for Tormek T4. You need: Natural Leather ~500mm x 25mm x 3mm Glue: Superglue, Epoxy or Siliconglue etc… Sandpaper ~#100 to roughen the surface of leather and disc Sharp knife to cut the leather Triangle ruler
This model uses 1/4-20 Bolt and nuts. ~2" of bolt or so works well. I usually print on the side with organic supports. 15% Gyroid Infill.
Different wall Mounts for Tormek Jigs
Adapter for grindstone with 20mm hole to Tormek. Fits JULA grindstone (243973). It must be pressed in, but fit will vary from printer to printer. It is possible to adjust with sanpaper or simular for a perfect fit. Is designed so that it…
Rändelmutter z.b für Tormek! Note: -A M12 DIN 934 Nut is needed
This bolts on to two existing holes, and for stability you can drill two more. The holes for the rods are 10mm, and I have used regular 10mm round stock as riser bars with the cross bar welded on top. Now you can use Tormek style…
Happy Printing :) - No Supports or brim needed :)!
If you remove grindstone during honing you need to put in a spacer. This is the chosen one ;-) a spacer with included threads! Print settings I used: Filament: Prusament PETG Layer Height: 0,15 Perimeters: 3 Infill: 25% Cubic Top/Bottom…
Print a couple of them in case of emergency… There is a chamfer on the side that goes against stone, that side should be UP when printing! Print Settings I used: Filament: Prusament PETG Layer Height: 0,15mm Perimeters: 3 Infill: 25%…
This is a Tormek LA-122 honing disc holder that fits instead of the normal honing wheel of the Scheppach 2000s. Parts has been oriented in the proper direction for printing. Only the outer part of the inner retaining ring for the big…
Summary: Replacement Rubber for Tormek Drive Wheel SA-250. Maybe it works with other Tormek Versions like T7 and SG-2000 too. Print Settings Printer: Ender 3 S1 Rafts: No Supports: No Resolution: 0,2mm Infill: 65% Filament brand: Filaflex…
Systainer sys3 437 interior for Tormek SuperGrind 2000. Printed the bottom inlay in 4 quarters. Full size stl file also available. It doesnt't fit into a 337 systainer, so I added a cavity to store an additional grinding stone on the…
I´ve printed it with PETg and -0.15 Horizontal Expansion. Printer: Artillery Sidewinder X1 Rafts: No Supports: No Resolution: 0,2mm Infill: 40% Filament material: PETg
These feet raise the Tormek sharpening system up higher. Handy for keeping the machine out of its own puddle. See the video here: https://youtu.be/9Hs2RRfNoJw
An affordable solution to setup the sharpening angle for knifes. printed in PLA black and white, layers 0.2 mm. 2 colors option for 2 items. Only one support required for the "base", other pieces without support. You need 2 M5 30 mm bolts…
Rubber feet for Tormek SA-250 and other/ Gummifuß für Tormek SA-250 und andere Modelle Note: Both parts must be put together only after printing. Use double-sided tape for assembly Materials: Tormek SA250 Fuß Gummi → TPU Tormek SA250 Fuß…
Protective case for Tormek KS-123 angle setting jig. I recently found the jig's plastic to be a bit deformed, due being loose in my toolbox. Not as rigid as other Tormek jigs. Bit of a bulky case, due to additional space reservations. Jig…
Eine Spritzschutzwanne für die Tormek T4 zum Enhängen in den Wassertank . Beim Schleifen spritzt es immer ziemlich herum und so habe ich mir eine Wanne konstruiert zum Einhängen in den Wassertank direkt. Der Spritzschutz geht knapp über…
Print with supports, with the pivotal shaft pointing down.
Labeled jig holders for the Tormek grinding station at our makerspace. Made to be easily readable, and easy for the user to know what is what and where every jig is supposed to hang. Designed so that the jigs sit safe in the holder, and…
Attention: This tool makes no sence for the 44mm tube and does not work with the english form --- i didnt know it until it was made because i am new with the tormek and sharpening ;D ... perhaps someone wants to remix it ;) Happy printing!
Working principle The fork provides an alignment edge through the grinder shaft and centres on the end washer. Use the right fork size for your washer and use the fuller-ed side towards the wheel. This guiding face should be very smooth…
LAGERBUCHSE FÜR HK1212 TORMEK T3 Category: Machine Tools
Držák na kotoučové kameny brusného systému Tormek.
250 mm grindstone holder for wet grinders like the Tormek T8. There is a model for one or two stones. The stones are held securely and can dry on the stand, while not wasting plastic like some very thick models. Printable on a Prusa MINI.…
This SF 60 is one of the first models of Tormek grinders - a greate machine - but after nearly fourty years the friction drive wheel gave up. So i printed a new one if you download it dont forget to leave a like - thanks The wheel itself…
Simple tool as addon for the Tormek SVS-50 sharpening tool. Works for 44mm "roughing-tube" English U-shape like “ Crown HSS roughing tube English U-shape ” For better printability its done by two single parts that will simple pressed…
This adapter allows a filament spool to be attached to a Tormek T8 wet stone grinder. The comparatively slow rotation speed of the grinder allows for a relaxed filament transfer. The adapter can also be used on the older Tormek T2000…
low cost replacement for the EZYlock nut to block the stone on the Tormek T8. Printed as a trial with PLA 0.2 laye 15% infill, I think PETG or other resistant material have to be tested.
I used Michael's model and duplicated it for two of my Tormek stones
An affordable solution to setup the sharpening angle for knifes. printed in PLA black and white, layers 0.2 mm. 2 colors option for 2 items. Only one support required for the "base", other pieces without support. You need 2 M5 30 mm bolts…
You want to teach yourself a new skill, but as a beginner, it is sometimes difficult to pay attention to many things at once. Especially if you are not sure if you are doing things right. To eliminate at least one variable, here is the…
Storage fixtures for Tormek jigs on IKEA Skadis peg wall system KJ-45 Centering Knife Jig KJ-140 Wide Centering Knife Jig SVM-00 Small Knife Holder SVX-150 Scissors Jig SVA-170 Axe Jig SVS-38 Short Tool Jig SP-650 Stone Grader WM-200…
I kept running into the stone of my Tormek T-7 every time I needed a hone something on the leather wheel (knives, long blades etc.). This spacer lets me take off the sharpening stone and and just use the leather honing side uninhibited.…
When you have to remove your sharpening stone to use the honing wheel, you can use this spacer to replace the stone. This should also work with the Tormek T8.
Redesigned to fit KS123 and KJ45 and holder for the spacer when removing the stone, storing the polishing cream and holding a felt marker. Thanks to @knives127 for a great design!
My machine's driving wheel cracked, I printed a new Petg out of plastic, 40% infill. You can take an old rubber wheel, install it from the pulp where there is a thicker edge so that it does not crack in the installation. Or you can…
Inspired by the model made by Luma for the T4, I made this one on the same principle, on Freecad. Two options: balls printed or purchased 10 mm metal balls (30 balls). Both are OK, but I suppose durability of the printed balls could be…
I made this jig for the front attachment section on the tormek t4. I'm using the soft Japanese water stone and I kept chipping it on the other jig attachment. The pins were turned out of t6 aluminum. it also has some small inserts brass.…
You want to teach yourself a new skill, but as a beginner, it is sometimes difficult to pay attention to many things at once. Especially if you are not sure if you are doing things right. To eliminate at least one variable, here is the…
I created a water drip tray for the Tormek T4. The tests showed that it works. Easy to print as it consists of two parts
The nut on the Tormek grinding stones is fairly special: M12 2 flutes / splines 4mm pitch (!) This is a perfectly fitting spare/replacement part, should you need one.
This is an extension of the water container so that you don't have to spill so much water when grinding. When all parts are printed glue them together.
This is my own design for a 3d printable support bar Sleeve for Tormek. I highly recommend to use a M6 or other threaded insert. The hole is 7,4mm wide and 8,7mm deep. I tested this design for my Tormek SA-250. It should also work with…
Horizontal Base for different wet grinders like Tormek. After print you need: -4x V2A countersink screw ~M5x20 -4x V2A washer M5 -4x V2A nuts M5 -2x V2A nuts M6 -2x knob screw with V2A M6x12 -Superglue -maybe you need a 12,5mm drill to…
Gridfinity storage for Tormek T4 basic toolset Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .3 Infill: 20% Filament: eSun PLA Category: Tool Holders & Boxes
Remix of the Tormek Drip Tray for FVB from @Leapstep_261016, this remix has space for the big round nuts used to level the attachments. The design is based on Drip Tray For T7 / T8 In Connection With Vertical Front Base » Schleifjunkies…
Scissor and longknive holder has cutout spaced to far from another (look at the picture) . I recommend deleating the space between the two cutouts interly with e.g. a negative volume in the slicer. I am unfortunetly not able to change the…
Storage fixtures for Tormek jigs on IKEA Skadis peg wall system KJ-45 Centering Knife Jig KJ-140 Wide Centering Knife Jig SVM-00 Small Knife Holder SVX-150 Scissors Jig SVA-170 Axe Jig SVS-38 Short Tool Jig SP-650 Stone Grader WM-200…
Its a new better version of my other XB-100 alternative modell. Now you can use the original Tormek holes. The original 4.8mm holes must be drilled to 5mm. You also need: 2x V2A M6 nuts (Muttern) 2x V2A ~M6x15 screws with handle 4x V2A…
Magnet clip for Tormek SuperGrind 2000 water trough to trap steel particles. May also fit on older T-7 models. Has place to glue 10x2mm cylinder magnets in place. Model is slightly bent inwards to pre-tension the clipping force. Onshape…
I find it difficult to control plane iron camber using just the Tormek SE-77 screws that release the swiveling mechanism. In addition, it is required to manually align the plane iron in the center of the grinding jig. I've created a…
this adapts the tormek LA-120 profile to fit most large bore felt wheels
![[Tormek T4] Water chute (side) // Wasserablauf Rinne für Seite (V2)](https://media.printables.com/media/prints/1f7bfad3-843a-4a91-b3c9-5246e7433d2c/images/9927319_fb942a56-a775-4c31-9230-e56c82e9fc65_9925a01a-f402-4f82-9404-6926f8efc15b/img_8524.jpg)
![[Tormek T4] Water Drip Tray (top) // Wasserablauf Schale für Oberseite (V2)](https://media.printables.com/media/prints/4cfc6f81-3215-4ec4-afdd-27ca08b3811b/images/9927166_835e2bfb-4e8e-494f-8922-04fa86b9e9c0_3e1cdd65-13db-4a9c-a7e6-fe86d425e70e/img_8740.jpg)
