Liczymy pasujące modele…
Introduction I purchased a used Berg trampoline and some of the knobs to fix the round, green mattress were missing. So I purchased some flexible cord (5mm, weatherproof) and designed my own knobs. The print file A file for printing in…
Trampoline net post brackets that use 3/4" EMT conduit to replace stock trampoline net posts. For my trampoline the EMT was cut to 80 inches long then bent at a 20-30 degree angle 20 inches from the top. I used the bottom bracket to mark…
After getting a request to transform a design into a printable object I've created this trampoline. It's based on the design of Christopher Jeschke which had the smart idea to use a balloon as base part for the trampoline. I've optimized…
The parts shown in the picture broke on my trampoline I modeled a replacement for everyone to use. Print settings don't matter almost at all, the part is made for 3d printing and should be printable with the vast majority of materials. I…
The key to the bouncy surface is to use this hack! Print Specifications Filament: PETG Specification Value Estimated Print Time (Ender-3 V2) 30 Minutes Filament Used 5.2 g Layer Height 0.16 mm Wall Thickness 5 perimeters Infill Density…
1.step: print Trampoline-guma Material - TPU Layer height - 0,2mm 2.step: print Trampoline-ram Material - PLA Layer height - 0,2mm IMPORTANT - stop on layer 19 and insert part “trampoline-guma”
Trampoline net holder. Designed for a 26mm pipe and a 6mm net holding ring. Print instructions Tested with PETG Resolution 0.2 mm Infill 80%
To protect the automower from be stuckt at the trampolin.
print 3 pla parts (bottom part glue together)….. ten use flexi material for TPU file (you can play with infill for diferent flexibility)
A model trampoline currently is in a state that will not bounce.
I lost a few of the plastic spacers which are used to screw the net poles onto the main trampoline body over the last winter, so i decided to give it a go and print the replacements. They worked perfectly without for a compelte summer. I…
Hi, to download Handle Trampolines End Cap, the end caps are on the 25mm tube, I had to make new ones because the ones from the trampolines are falling apart, my are stronger :) Handle Trampolines End Cap is my project, printed and works…
Our trampoline and the robotic lawn mower are not best friends. These brackets are designed to help them get along better. With the bracket installed on all edges of the trampolines w-shaped struts, the mower isn't lifted anymore.…
These spacers go between the Acon 16 trampoline legs and the net support poles. I broke and lost several when I was disassembling and moving the trampoline, and printed out some replacements. PRINTING I printed it in PETG with 70 percent…
Die Netzbefestigungen bei unserem Trampolin waren von der Sonne ganz brüchig geworden und zu einem Großen Teil schon defekt. Ich habe diese gezeichnet und ausgedruckt. Jetzt ist das Netz wieder fest und sicher.
This is fairly simple recreation of caps that you can buy for your trampoline. Ideal for pipes with ~26mm of inner diameter fairly simply to print - with bit of care also without supports. PLA or PET should be ideal
Classic roblox trampoline
The spacer places the safety-net pole (25 mm outer diameter) at a distance of 5 mm from the base frame tube (39 mm outer diameter), with a center bore for an M6 screw. The FreeCAD file is provided to allow for adaptations to different…
End cap for trampoline Category: Sport & Outdoors
Abstandhalter für Netzstange Durchmesser 25mm und 38mm
I made this out of boredom hoping somebody might want to download it! I think if you would want to print this you may want to move the ball somewhere else and flip the trampoline upside down because it may just be easier to print that…
Normally I'd post a link to the stream where I designed this part, but unfortunately I didn't stream this one, so all you get is this link to my channel where I design things like this: https://www.youtube.com/c/ClarkSchaefer/videos .…
This is a simple Model i designed because the net-holder of a friends trampoline broke down and he couldn't find a replacement for it.
Replacments net caps for our outdoor trampoline. They also hold on to the protection net. I used a big zip tie to attach the net to each cap. See picture for model comparison. A diameter of 25.5mm suited perfect for me. Print instructions…
Upper rod cover originally made for trampoline, but can be used for any rod and also model parameters can be adjusted based on requested rod diameter. This one is for rod with 25 mm inner diameter. Print instructions Supports needed at…
For trampoline Gofit. Print instructions I used PETG, but if you want print this by ABS/ASA you must have box for 3D printer.
inspired from https://www.thingiverse.com/thing:4539088
Height is 67 mm and diameter is 62 mm. Replacement for poor quality original. Printed from PETG
This is a replacement end cap to go on the top of the vertical poles, supporting the top ring which holds the safety net. Many of my original brackets snapped off after a few years so I designed this replacement as EXIT will not sell you…
This model is for use with 25mm (~1 inch). It is intended to support Safety Net. If the Trampoline is outside you should print it in with PETG so its hard and it resist weather conditions. You can print it without supports. Print details:…
Trampoline – Gravitrax compatible Here I present my trampoline with TPU net. There are two versions available for download: The first version is based on a normal building block. It is twice as high and can be used anywhere. The…
Replacement net holder top caps for Plum trampolines. I've replaced the metal spring button with a designed-in clip, though it's not a great success and might snap depending on your material. However, I've found these fit in and hold a…
Modeled against my own trampoline Pole cap. Photo is only for reference
This piece goes on top of the post that hold the safety netting. Print vertically with supports or horizontally without. 100% infill for best results.
This is a trampoline spacer, used to hold the net support arms to the frame. I built this model to print after a wind storm damaged our trampoline. Ours was purchased from Sam's Club. Print Settings Printer Brand: LulzBot Printer: TAZ 5…
step for 78mm pipe, for easy access to trampoline, without ladder, perfect for those who have a robo-mower
This is a replacement locking clip / top cap for the pole holder on a BERG trampoline safety enclosure. The part clips over the enclosure pole and locks it into the base holder that is attached to the trampoline frame. The original…
if you download the model pot it to 40% size
Mushroom part used in the EXIT trampoline. It is little bit reinforced than original one. Spring hole works. Print Settings Rafts: No Supports: No Resolution: 0.35 Infill: 10% Notes: 2 perimeters, 3 solid layers
I needed a replacement for lost trampoline footpad. Made in TPU at 210 degrees, 30mm/s speed
This is a wall mount for little tikes trampolines with the large red feet. The feet snap securely into the cups and keeps the trampoline close to the wall. I used 2 mounts on the feet that have the handle bar attached to them.
trampoline net holder diameter 32mm easy printable easy customizable for other diameters Print instructions you can print it with a thick nozzle no support needed you can use PLA, but ASA might be better for the outside using
Trampoline Leg Barrier for Robot Lawnmowers Prevent your robotic lawnmower from getting stuck on trampoline legs with this practical 3D-printed connector system! This model allows you to attach wooden slats to the legs of a trampoline,…
This is a replacement part for a trampoline safety net. Diameter up to 26mm is suitable.
3D PRINTING SETTINGS PA12CF Infill: 30% Outlines: 5 schmeißt eure Sachen nicht weg versucht sie stattdessen solange wie möglich zu erhalten!
Designed with WSA measurements, these trucks will allow you to practice your streetboarding grabs, spins and flips on a trampoline, without worrying about damaging anything. The test pair I've printed so far have been in PLA (20% infill).…
Original broke, needed a replacement. Printed in PETG, as this will get a lot of sun and weather exposure. FreeCad model is a bit messy, but supplied if anyone needs to make changes to fit. Oct 9th: Added a last picture. Petg just fine…
This is a part for the Skywalker 8' Trampoline sold at places like Walmart. It replaces the plastic tops of the net poles (it protects you from landing on a sharp pole, and attaches the net to the poles). The nut slot is slightly larger…
This is a foot created to pressure fit over a 1 inch trampoline leg to keep it from marring the ground, but could be used for any pipe really. Printed preferably in TPU for its softness to not scratch the ground, although any material…
Alternative net holder for Ultrasport trampolines that you can use instead of the cap, that comes with the trampoline. It is designed for tubes with an outer diameter of about 25.5 mm. I use it with an 8 mm elastic cord that is fixed with…
Bei unserem Tupelo Trampolin, ist nach 3 Jahren oben am Netz ein Verbinder gebrochen. Da es leider kein Ersatz zu bestellen gibt habe ich dieses selbst nach konstruiert. Gedruckt habe ich es aus ASA
My little boy tried his hand at tinkercad. He designed these leg caps for our trampoline. I told him may be someone else can benefit from his design. So here it is. It'll totally make his day if someone else can benefit from it. Inner…
Made this trampoline as a voucher for a friend. Text can be easily added in the slicer. Can be printed in multicolor or a single color, or color change depending on the height. Should be printed with the feeds to the top, but its easier…
Leicht zu drucken und sehr stabil durch optimalen Faserverlauf.
https://youtu.be/46oyP1UV6fY These NeoPixels makes you wanna jump! Learn how to upgrade a cheap trampoline with interactive NeoPixel LEDs. Use Adafruits ItsyBitsy and a vibration sensor to make a trampoline light up when you jump on it.…
Mit dem Spannring kann ein aus Gymnastikband hergestellter Bezug auf dem Trichter fixiert werden. Prima zur Reparatur, wenn das Original gerissen ist, oder um aus Trichtern zusätzliche Trampoline herzustellen. Kurzes Video der XM…
Rubber trampoline foot for a mini trampoline. The actual foot has two washers inside to prevent the feet from pushing through the rubber. They are about one inch diameter. You would print this using flexible filament. Category: Toy & Game…
Just a few models of the plastic parts used to assemble a springfreetrampoline.com trampoline
Clips to allow a Veriflite time of flight sensor to attach to a EuroTramp bed. They don't work well on Nissen beds but Continential beds with the metal anchor bars work fine too.
The elastic bands to keep the buffer/cover in place broke, so I made this as a replacement to keep the buffer in place using laundry drying rope. To tigthen the drying rope around the buffer I used the rope tensioner found here:…
A simple trampoline net holder. It is recommended to print out with PETG material.
save your floor with (TPU) feet for your kids trampoline
The slot to enter the rod is tight fit but prevent the rod jumping out. I printed it flat laying on side to have the forces across the layers.
Spare Distance Insert for Trampoline was created for broken replacing originals. We have a lot of broken inserts after few months jumping. It should be printed from some strong filament like PC or PP.
My kids’ net on the trampoline keep coming off. The plastic cups that held the net up became brittle from the sun, so they fell apart. They were also a pain to put on and thread the screw through. With this solution, you can simply pop…
I created a Trampolin Mobil Mount for a Xiaomi Mi 8 Pro The Size of the Mount is: 164,40 mm x 82,417 mm x 12,90 mm (LxBxH) All parts are printed in PLA with 15% infill You need 2parts of the Mount - the Punchhole ist 30,8 mm Print…
Replacement washers for the bolts on the legs of a springfree trampoline. I printed in TPU/Flex at .3 resolution and 0% infill. I don't know how many I actually needed so I just printed 30.
Net holder T joint for a trampoline made by Smyth Toys. It is recommended to print with ASA to be UV resistant.
Update 12.07.26: mit Filament PEBA 90A getesetet, deutlich bessere Sprungeigenschaften. (siehe 2. Video) Dieses Trampolin hat eine größere Fläche und einen sehr kleinen Rand Das Sprungtuch ist umlaufend 0,4mm kleiner um eine Grundspannung…
Id recommend printing solid infill, or at least the screw part make infill solid.
My trampoline feet broke so i had to design some simple feet. I have tried with PLA and it holds pretty good so far. I believe with petg or tpu will be even better How about buy me a coffee buymeacoffee.com/spank7
Bei regelmäßigen und intensiven Gebrauch eines der günstigen Trampolins geht schon hier und da mal was kaputt. Aber wozu hat man denn 2 3D Drucker?
A friend was missing 2 top caps for a trampoline. So I measured one of the original top caps, modeled it, printed 2 new copies and it all fit first try.
For bars with a diameter of 26mm. PETG, 4 obvody, 15% výplň
TPU foot for small trampoline on the inside a big washer has to be placed
Print with PETG or better for outdoor use. The printed one in the picture is white. Printed with 100% infill in PETG
A STEP file is included, allowing you to easily adjust dimensions to fit different trampoline models and pipe diameters.
made these so my robomow RM1000 could pass below the trampoline :)
After a few seasons the net of the trampoline got holes where the metal tubes were holding them. So I designed these end caps which slide on the metal tubes on top. I added a small loop to hold the net with a cord.
Designed for replacing the plastic holder for the pole of the the safety net form a trampoline print it in abs for strenght and durability
The kids got thirsty jumping on the trampoline and their water bottles placed on the rim constantly fell down or rolled away. So I designed this mug holder which is easily attached using one or two zip-ties on the trampoline safety net…
My trampoline hook broke, so I made this. It's nothing fancy, everything should be visible on pictures.
Replacement top for a Trampoline pole, should fit most makes/models.
I printed it in Anycubic ABS 100 celsius bed temp and 250 hotend temp. its my first thing i uploaded. Hope you like
This part holds the safety net ring in place on top of the trampoline poles. Original replacement parts are ridiculously expensive print your own solution. Original part dimensions: - Outer diameter: 30mm - Inner diameter: 26mm - Height:…
Heavy-duty lacing posts designed to secure a trampoline on a catamaran. These mushroom-shaped fittings are built to handle significant lateral loads and are intended for use with M5 countersunk machine screws. These have been on the boat…
End cap for mounting the net to a trampoline of make "Super Jumper". This is a USA based producer, but their trampolines are sold around the work. I bought my trampoline ( Super Jumper 3x4,6m ) at Europris in Norway, and they are still…
plug the holes from removing the safety net so they are no sharp edges
These flags are designed to help stop robotic lawn mowers from trying to climb over low trampoline legs. They create a taller, more obvious obstacle that is easier for the mower to detect before reaching the horizontal frame. They were…
trampoline hook for safety net but little bit bigger and stronger. original one broke quite fast at least 80% inflill and please use at least PETG or ABS. PC blend would be better or any other strong material
I printed it with plastic from PET bottles . But PETG also can be used. Don't use PLA since it may melt due to the sun. Have fun!
A trampoline net holder for Jysk Summen. All mine have broken when taking the net up and down. It is just to print it. This only works on certain models since the cylinder goes inside the net post.
A simple cover for our Trampolin including a fixation possibility with a screw.
I found it really too long to make knots to attach the spring protection foam on my daughter’s trampoline.
Um den Kindern an heißen Tagen eine Abkühlung zu spendieren, haben wir als Trampolinzubehör Wassernebler gekauft. Diese sind mit einem 6 mm Schlauch verbunden. Um den Schlauch demontierbar am Trampolin zu montieren, habe ich diese…
Slide from left or right. Print it from PETG.
This is a heavy-duty replacement cap for the safety net enclosure poles of the Alice's Garden 250 trampoline (compatible with other models using the same pole structure). The original factory-injected plastic caps are prone to snapping…
Bracket for Airtime TOF sensors and Magnet from Princess Auto Category: DIY
mare de devoir nettoyer des déjection d'oiseau en tout genre sur les plage d’accès de votre trampoline ? voici LA solution
