Liczymy pasujące modele…
I strongly recommend printing the model horizontally to give the snap lock more stability and durability. Feel free to support my work and leave a tip.
Sony NP-FZ100 battery case would be nice if you could post some photos after printing
This is 4x holder for the Sony NP-FZ100 battery. There is also a 2X version in the files. The lid attaches to the holder with 3x3mm magnets. Also attached are the Fusion 360 files. If the fit is too snug, please modify the current offset…
Very practical battery holder for 2 NP-FZ100 batteries + 2 SD cards and 2 Micro-SD cards. I got the idea from the Sony Facebook Group, but the creator removed the file from thingiverse and it is nowhere found again. As i found the Design…
------------------- Sept 2026 Update ----------------------- Following some helpful feedback, the original models have been marked as "DEPRECATED". The updated versions have an improved fit, and should hold the batteries more securely…
I've printed vertical ('sony' face on the plate) with support only for the top retention overhang, the small guides on both internal borders can be printed without any support. I tested it with 0.1 layer and with 0.2 layer, 20% infill;…
The idea was to use one per battery. And write on each side if the battery is full or empty. Push the battery from the open side until it snaps in.
I made multiple Sony NP-FZ100 Batterieholders for Gridfinity. 1xBatterie 1x1x3U (6U) 2xBatteries 1x2x3U (6U) 4xBatteries 2x2x3U (6U)
Sony NP-FZ100 1x2 Gridfinity bin stores 3 Batteries, and stacks when empty.
I have sliced the model in cura and added supports below the notches. Variant 2 has serrations on the sides that were intended to make it a grippy surface to aid removing the cover. But pressing on the side also jams the cover to the…
Holder für two Sony NP-FZ100 batterys. I printed two in different colors to know which battery is full or empty.
BEAR MINI FRAME - Z10 This modification was initially adopted to achieve better results with flexible filaments (using a direct drive extruder) and a stiffer frame for faster printing. Since then, Input Shaper was given as a free upgrade…
Box na Sony baterie NP-FZ100 dvě varianty pro 6kusů a 12kusů (skládá se z vrch, spodek a 2x latch) Adaptér pro SD 5ks nebo CfA 7ks (zabírá místo jedné baterie) Je potřeba použít M3x30 šroubek na jeden box 6ks (4x latch, 2x pant) Jedná se…
stackable gridfinity 1x2x8 holder for two sony fz100 batteries. sd card slot is a bit of a ‘had-some-room-left’ sollution but it is possible to get it out ;)
Technics AEH-AZ100 charging case protective TPU skin
Belt holder for sony battery. It is equipped with a fuse, it is very tight. Printable version without supports it is possible to overcome the fuse by force. Version for printing with supports, the fuse must be unlocked before removing the…
Printed with fuzzy skin fuzzy skin thickness 0,1 fuzzy skin point distance 0,1
Skadis batteryholder for sony camerabattery.
Oil filter wrench for Kawasaki Z1000 2010 oil filter. Fits for HF303 Hiflow and original Kawasaki oil filter. Ratchet 1/2in. Category: Hand Tools
Holds four, Sony NP-FZ100 batteries with a snug enough fit to hold batteries securely while in a backpack. To remove a battery, just give it a little push from the hole in the 'bottom' side. I like to keep the fully charged batteries with…
GUIDE https://www.instructables.com/Z100s-3D-Printed-Symmetric-Wireless-Mouse-Guide/ VIDEO GUIDE: https://youtu.be/o0P37Avcor0 -60g with AAA. Mass will vary based on battery and print material. -Wireless using G305 Internals -Rechargeable…
Il existe d'autres modèles à imprimer pour protéger les batteries NP-FZ100, mais celui-ci est une version minimaliste conçu pour protéger juste les contacts, sans prendre trop de place ni de poids. Le couvercle est bien serré sur la…
I recently bought a Beeline navigation device for my motorcycle. The mounting option for my type of motorcycle were either limited location wise, or bulky and ugly otherwise. So I decided to create my own option. In the cockpit attached…
A quick remix from @Hami's designt to fit a single spare battery.
This model gives you the possibilty to mount a (good) aliexpress bicycle mount on a Kawasaki Z1000 steering block. This block is around the handle bars and therefore the mount cannot be attached directly to the bar itself. There are three…
Skadis holder for 2 NP-FZ100 batteries, print with supports
Made this station to keep my favorite tools organized. It might fit other machines, but i only tested my Bezzera BZ10 . The fitting for the hanging part is 3.6mm in CAD. Any 58mm Tamper will fit (58,9mm in CAD) and the other spot is made…
I wanted to carry an extra battery on the front of my backpack using Peak Design's Anchor Connectors or Think Tank Red Whip bungee straps. The Red Whips are really tight, but they do work. I used Inferno3D's (on MakerWorld) remix to remix…
A bolt cap for the Z10 fork. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament: Prusament PETG Black Category: Parts
A replacement for the factory fork covers for the Kawasaki GPZ1000RX (Ninja 1000R or ZX1000a) These thread onto the schrader valve cap threads (pictured last), unlike the originals which are just snap fits into the top of the fork tubes.…
Ein Rahmen zum einstecken eines Ladegeräts - für Sony NP-FZ100 Akkus - und zur montage z.B. an einer Wand. Das Ladegerät lässt sich durch die seitliche Öffnung herausdrücken und sitzt gut in der Halterung
Hi, I am proud to present you a HDD case extension to install a second hard disk drive for the Zidoo Z10 Pro. The installation of the set is very simple : just move the feet of the box to the new one, install the hard drive and put the…
The brand you know now available to print yourself. I suggest printing walls two layers thick at 0.6 or three layers thick at 0.4. printable on MK3 I3 Strongly suggest using a strong PLA: Prusa Blend, CC3D Max, Inland Plus. Hardware: two…
This is an insert for my Eurobox/Gridfinity-Transportation-System to accomodate the Panasonic FZ1000, some (micro-)-SD-cards and a spare battery. It is 3.5 x 3.5 Gridfinity-units in size. I cut out the corners from this square to make…
Kawasaki part 920751762 is no longer produced. This is a near perfect replica of it and should be printed in a flexible material: Nylon, TPU, Ninjaflex, etc. The factory part has two cylindrical recessions on the bottom, most likely for…
I made my first version of these holders a few years ago for my camera batteries, and I really liked that I could see what is charged at a glance. Just keep charged ones with the contacts down, and drained ones flipped the other way. I…
Yokomo YZ10 91 Works Front Knucle Print Settings Printer Brand: Zortrax Printer: M200 Rafts: Yes Supports: Yes Resolution: .09 Infill: 100 Category: R/C Vehicles
This is a remix of a popular NP-FZ100 battery holder that holds 2 batteries but it is now a waistband clip model. I have added a waistband clip that makes this great for event photographers who have to change their batteries often and at…
Noctua 92mm x 14mm fan case for Minix NEO Z100-0dB. https://noctua.at/en/products/fan/nf-a9x14-pwm https://www.minix.com.hk/products/z100-0db-fanless-n100-mini-pc The fan is connected to a USB port (5v).
Design: Remixed from 490 MFG's design , brought into spec with Gridfinity Refined for magnet and screw support and still compatible with all regular Gridfinity spec baseplates. Print Settings: No special print settings are needed. I…
Um die empfindlichen Lamellen des Objektivverschlusses beim Transport zu schützen. Passt für Lumix DMC-TZ101 Innendurchmesser des Deckels: unten 58,8mm, oben 59,6mm
It is a great mini PC but under a constant heavy load in the summer heat eventually the Wi-Fi stops working. This fan shroud clips over the case. The 80mm fan I chose is USB powered and has variable speed. I found the lowest speed was…
This piece provides a hot air flow block from the front radiator up through the E-Brake lever on 2016-2018 Yamaha YXZ1000R cars. This replaces the paper towel I crammed in around the E-Brake handle to stop getting blasted by really hot…
Gridfinity box for Camera batteries USB Charger (for NP-FZ100 / Alpha Sony batteries in my case)
This is a replacement model for the bracket that goes on the Zhumell Z10 telescope to hold the finderscope. Despite testing the hole size for the tightening screw, after printing it turned out to be just a bit small for me. You may need…
I made a 1x3x6U Gridfinity Holder for my PATONA NP-FZ100 Charger.
Lipo battery box for Yokomo YZ10 Category: R/C Vehicles
I do have a special backpack for photographic gear. Often I do not want to take that much gear with me. Especially on short city trips etc. Then I take a day backpack or a simple shoulder back. Putting in the camera unprotected has then…
small and simple tray that fits my bluetooth in-ear headphone case perfectly. I use it with an angled USB C plug. USB-Charging Port accessible easy and fast to print, no supports designed close to the original case, rounded corners etc.…
This print combined three requirements that I had for my new Formuler Z10 streaming device: move the device from the tv stand to the wall hang without using screws remove easily to bring with me to other TVs This way you can unplug it and…
This is a custom wall mount designed for the K&F Concept NP-FZ100 battery charger (with dimensions of approx. 21.5 × 54.1 mm) , which is often bundled with dual battery packs (2600mAh). The mount is fully compatible with the IKEA SKÅDIS…
This is an alternative for centering the top of the Z axis threaded rod tor the P3Steel frame. My frame is from Orballo, and it has a hole on the top for passing the threaded rod through, it is 12mm in diameter. My threaded rod is 5mm. I…
klip staci nacvaknout(zasunout do drazek), zalezi jak mate serizenou tiskarnu. nekdy lepe pro jistotu prilepit ;)
Case HDD Festplatte Zidoo Z10Pro um eine über SATA angeschlossene Festplatte unterzubringen. Ein ähnliches Modell existiert hier schon, dieses passte aber nicht auf mein Druckbett von 220x220mm. Die Füsse des Zidoo werden abgeschraubt und…
Because the splashing annoyed me, i've built this small fix. The Version you see in the picture is slightly too long / mismatches the chamfer, this is fixed in the current 3mf file.
after the first winter, this part was broken. So I designed an easy to print replacement. the second design has two holes to secure it with a cable tie. print with 100% infill to make it stable
This is a custom wall mount designed for the RAVPower and BLUMAX NP-FZ100 battery chargers (older generation models) , used with Sony Alpha cameras such as A7III, A7IV, A7R III/IV/V, A7C, A7S III, A9, FX3, FX30, and others . ⚠ Please…
Yuasa YTZ10S battery case for 1983 Yamaha Virago XV500K Motorcycle Hardware required for assembly: 4 pcs M6 x 100mm bolts for the frame 4 pcs M6 lock nuts for the frame 2pcs M5 x 20mm bolts for the base 2pcs M5 standard nuts captured in…
This mount was primarily developed for telescope pier mounting. It provides basic mist/condensation protection for this fanless minipc. It won't protect from huge rain but some light sprinkles should be fine. the cable mounts on the sides…
Voici un support GRIDFINITIRY pour batterie NP-FZ100 pour les boitier Sony Elles ont toutes été imprimé en PLA et avec un remplissage a 5% de type gyroïde Il y'a un petit gravage "BATTERIE" -------------- Here is a GRIDFINITIRY battery…
For me, the DreameBot Z10 Pro dust bags cost 15€ for 3 bags PLUS shipping, which is crazy. So I figured that I would just copy the adapter and use it for cheaper dust bags. The only thing is that this doesn't have that closing mechanism…
A compact, rugged-style case for two Sony NP-FZ100 batteries and your choice of memory cards . The hinged lid, reinforcing ribs, and separate latch keep everything together in one organized package. Choose the card layout that matches…
I added an M.2 ethernet controller to get a second LAN connection on my Minix Z300-0db. I had the ethernet connector board just hanging out loose out in a simple 3d printed box, but I wanted it more permanently mounted to the machine, so…
Precision Alignment for Charging This is a functional 3D printable adapter specifically designed and tested for the Technics EAH-AZ100 headphone case. EAH-AZ100 supports wireless charging, its small form factor prevents it from reaching…
Diese Schutzkappen ermöglichen eine beschädigungsfreie Demontage und Montage eloxierter Muttern an der Gabelbrücke sowie der Telegabel. Es sollte ohne Infill gedruckt werden.
Dreame Z10 / Z10 Stationary Crevice Tool Release Button (Reinforced) This is a small replacement release button / lever for the slim crevice nozzle used in Dreame Z10 and Z10 Stationary vacuum cleaners. The button is responsible for…
Here's a charger for Panasonic Lumix DMC-TZ10. Also suitable for other cameras, see list below. Everything you need you can see in the photo (pogo pins x2, piece of wire x2. charging controller TP4056 x1). Panasonic DMC-TZ10 Panasonic…
A very simple friction fit lid NICKSH Sony NP-FZ100 battery case. I'd recommend using a rubber band as it will probably become less of a friction fit over time, but it works well enough to keep everything in place.
very basic, but functional output shaft seal driver for 1st gen z1000 and z750 engines.
Gridfinity Patona Charger Sony NP-FZ100 Sony A7IV A7III A7RV A9III Mirrorless Cameras I added small gap to eliminate Hull line when printing.
As far as I know, this part has been discontinued, you can make it from various materials or use it as a carbon fiber mold.
Disclaimer: This is mainly to keep track on what I did while building (otherwise awesome) Prusa Mini Bear mod. I never intended to publish it, but did. Consider it as Work In Progress and bear in mind, that credit will be given due time…
Simple kawasaki z1000 keychain for best results recommended 0.2 nozzle.
Simple kawasaki z1000 keychain for best results recommended 0.2 nozzle.
A lightweight, minimal snap-on cover designed specifically for the BlackBerry Z10. Built to provide baseline scratch resistance and back protection while keeping all edge ports, buttons, and camera openings accessible. Snug Fit: Precise…
It's Sony 3x NP-FZ100 battery holder but on horizontal. I printed it with 0.6mm nozzle at 0.35 layer height with PLA.
I added an M.2 ethernet controller to get a second LAN connection on my Minix Z300-0db. I had the ethernet connector board just hanging out loose out in a simple 3d printed box, but I wanted it more permanently mounted to the machine, so…
Voici un support GRIDFINITIRY pour batterie NP-FZ100 pour les boitier Sony Elles ont toutes été imprimé en PLA et avec un remplissage a 5% de type gyroïde Il y'a un petit gravage "BATTERIE" -------------- Here is a GRIDFINITIRY battery…
Depending on accuracy of print , feet may require clearancing with rotary tool or engraver to fit over studs.
This battery dispenser can hold 5 Sony NP-FZ100 batteries. This helps you cycle through your batteries more consistently instead of using the same one over and over. The support structure breaks off very easily. The support structure is a…
The internet has many kinds of NP-FZ100 battery cases. I found some of them made of TPU were sold in places like Aliexpress, and I thought I could make them myself, so I made them. The symmetrical storage allows you to put the battery in…
This is a remix of the original no-screws parametric box, modified to hold six Sony FZ100 batteries securely.
It's Sony 3x NP-FZ100 battery holder but on horizontal. I printed it with 0.6mm nozzle at 0.35 layer height with PLA.
Prints well with PETG on it's bottom with minimal supports on the top of the SD card area.
Sony FZ100 battery charger holder / wall mount.
1st model I ever created. A simple dispenser for Sony NP-FZ100 batteries that can be mounted on Multiboard/Ikea Skadis.
The NP-FZ100 battery is used in the Sony A9 and A7-RIII. I had previously designed a battery for the A7-RII's batteries - something that was really needed given the rate you go through them. Now with the additional A7-RIII body (and…
Rear Knuckle for the Yokamo YZ10 91 Works RC Car Print Settings Printer Brand: Zortrax Printer: M200 Rafts: Yes Supports: Doesn't Matter Resolution: 0.09 Infill: 100% Filament: Amz3D ABS Grey Category: R/C Vehicles
Super simple battery holder for up to 4 Sony NP-FZ100 Batteries.
As a full time photographer I need a lot of batteries but they don't make nice cases to store them all together so I made one. I had 2 needs with this case which are it had to carry 4 batteries and it had to lock closed. I successfully…
Depending on accuracy of print , feet may require clearancing with rotary tool or engraver to fit over studs.
Funda protectora para tus baterías Sony NP-FZ100 ( Sony aIV ). Yo llevo tapas de diferentes colores para diferenciar si la batería está cargada o si es una batería que saco de la cámara porque ha quedado descargada. Impresas en PTEG
This is a insert for Sony FZ100 camera batteries and compatible versions. The insert is designed for the incredible Whity's Rugged Box. It can house two Sony FZ100 batteries. Use more of these inserts to house as many batteries as you…
This battery dispenser can hold 5 Sony NP-FZ100 batteries. This helps you cycle through your batteries more consistently instead of using the same one over and over. The support structure breaks off very easily. The support structure is a…
I love listening to the cheap EZ10 earbud, but its design had a huge con for me from the start, the open charging case collected all the dirt from my pockets. Not anymore! I recommend slicing up the included STEP file, I printed mine with…
Protective case for the Sony NP-FZ100 battery. No support is required for printing.
Kawasaki KZ1000, KZ900, Z1000, Z900 oil cap fits most kawasaki models. M30x1,5 threads
