Led light Prusa Mini Enclosure mount - Aca lighting 5W DAPO560
We calculate the final price from your selected file. You review and accept it before payment.
Preliminary estimate for PETG
€0.80 – €0.98 net (excluding VAT)
For file: light_cover_v0.5-1-2_0.4n_0.2mm_PETG_MINIIS_40m.bgcode
This is an estimate for one file. You’ll confirm the exact price before ordering.
File and estimate settings
File used for this estimate
Average indicative estimate: €0.89 excluding VAT (range midpoint).
- Weight reported by the author
- 17 g
- Print time reported by the author
- 40.2 min
- Source material
- PET
- Estimate material
- PETG
- Estimate printer
- Bambu Lab P1S - 0.4 nozzle
- Estimate process
- 0.20mm Standard
Indicative estimate for the selected file only, based on the author’s weight and print time. File variants are not added together. The final price is calculated after file analysis.
Saved on this device.
Led light mount for Prusa Mini Enclosure top transparent panel
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 6
- Makes
- 0
- Views
- 115
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Prusa Parts & Upgrades
- License
- Creative Commons — Attribution — Share Alike
Hello,
i made mount for cheap LED panel Aca Lighting DAPO 5W, 520lm - 30cm long led panel with button and power from 230V. It costs about 6€ + 4€ power cord. I want to keep led outside from enclosure, its generating some (not much) heat.
https://www.alza.cz/aca-lighting-dapo-5-w-230-v-6000-k-520-lm-120-ip20-300-mm-d12833344.htm
https://www.alza.cz/oem-napajeci-230v-2pinovy-1-8m-bily-d4828120.htm
Print settings:
- PETG material, printed from Prusament PETG recycled Galaxy black 240 degrees celsius hotend, 90 degrees celsius printbed
- Prusa Mini+ frendly, just need to cut cover in half (i printed it with dovetail joint)
- Printable without supports, just need to adjust correct orientation
- 0,2mm layer height, 4 perimeters, 4 top/bottom layers for holders
- 0,2mm layer height, 4 perimeters, 4 top/bottom layers, 80% speed and 0,5mm skirt for cover
- Print 2x light_holder_side
- Print 1x light_holder_middle
- Print 1-2 light cover (not necessary, if you dont want to shade direct light)
For mounting, you will need:
- 6x M3 nut (included in basic parts)
- 6x M3x8-12mm bolt (included in basic parts)
- Be careful, DO NOT SCREW IT TOO TIGHTLY
Assembly instruction:
- Install light connector cover from original package
- Attach printed light_holder_middle to light
- Remove 2 nylon joints from top transparent cover
- Add 2x M3 nut to holes in holders
- Install holder, bolts will be from bottom to top
- Repeat for remaining 2 holders
- Done
Warning for light usage:
- Recommending to read light manual for instalation, or read just at least following paragraph
- This type of LED is generaly intended as kitchen light. It can be chained with multiple lights in series, there is pass-through connector in package. If this light will be used alone, its IMPORTANT TO ADD COVER TO SIDE WITHOUT POWER CABLE ATTACHED. If not, there will be connector under voltage, accessible to touch. Plastic cover for light connector is attached in package.
- There is free space around and printed cover (for shade) doesnt cover light absolutely - its intentional because of natural light cooling.
Note - light is about 30cm long, and there is some space remaining on both sides. Its not serious trouble, but if someone want, some cover or modification should be made.
Hope you will like it.