1 / 4
Magnetic PC4-M10 Couplers for INDX Filament Sensor — image 1
1 / 4

Magnetic PC4-M10 Couplers for INDX Filament Sensor

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

INDX filament sensor adapter with magnetic PC4-M10 couplers. Now with experimental (untested) direct-mount sensor tops.

Rating
5 / 5
Likes
2
Downloads
4
Makes
1
Views
107
Reviews
1

Updated at source:

Model information

License
Open Community License v1.1

This adapter attaches to the face of the INDX filament sensor and allows you to connect reverse Bowden tubes via PC4-M10 fittings. But instead of those fittings screwing directly into the adapter, each is screwed into a separate magnetic coupler, and the adapter has corresponding magnets to hold the tubes in place.

New and experimental: direct-mount sensor tops. If you don't have room for the adapter, there are now replacement INDX filament sensor tops with the magnet pockets built in. These have not been printed or tested at all yet; they exist only in CAD. See "Direct-Mount Sensor Tops (Experimental)" below before printing one.

Bill of Materials

The adapter was derived from VertigoMakes' INDX Filament Sensor Bowden Adapter - ECAS04 & PC4-M10, and as such uses the same two M3 x 18mm socket head screws to attach to the original INDX filament sensor, although M3 x 16mm also worked for me. (The direct-mount sensor tops use the stock M3x12cT screws.)

Unlike that model, I only made a version for PC4-M10 fittings, not ECAS04. I used BIQU fittings (https://www.amazon.com/dp/B0F6CQT461), but other brands should work. Note that despite the name, the thread on a PC4-M10 is a 1/8″ BSPT (sometimes called PT 1/8) thread, and that's what this part was designed for. You can tell because 1/8″ BSPT is around 9.7mm in diameter, as opposed to the 10.0mm you'd get with a true M10. Still, double-check that your fittings have the correct thread design. Also ensure you have pass-through fittings, this model expects the PTFE tube to continue through the entire fitting.

For the adapter versions, you will also need 24 circular magnets. I originally built the version with 6x2mm magnets, but found that unless the PTFE tubes were aligned perfectly, the couplers didn't attach reliably. I then built the version with 8x3mm magnets and found that to be much more reliable. Nonetheless, I've included the 6x2mm version, as well as 6x2.7mm and 6x3mm versions which I never tested, for completeness. The 8x3mm adapter is slightly larger than the 6mm versions: the magnet tabs extend about 4 mm past one long side and a few millimeters past each end, so check that nothing on your sensor mount sits in that space.

The direct-mount sensor tops need fewer magnets: 8 in the sensor top, plus 8 in the couplers (16 total). The 6mm versions use the same couplers as the adapter versions, but leave empty the "middle" pocket at the point of the triangle (the one equally spaced from the other two). That's the one that would sit over the ring channel.

Each adapter is engraved with its magnet size (M8x3, M6x2, M6x2.7, or M6x3) on the side that faces the sensor, so you can tell them apart. The couplers and direct-mount sensor tops aren't labeled, so keep each set together.

Printing Considerations

The adapter and couplers should print without supports, but keep in mind the print orientation: in both cases the magnet pockets should face onto the plate. The square poke-out holes in the magnet pockets are shaped to allow the back of the magnet pocket to bridge easily (while helping you remove the magnets if you got the polarity incorrect). The bridging can still be a little rough on the 8x3mm version with its larger magnet pockets, but since those surfaces are covered by the magnets when in use, it's not as big a deal; more bridge cooling in your slicer may help.

The direct-mount sensor tops print in the same orientation as the original sensor top, so their magnet pockets are horizontal. Each pocket has a teardrop-shaped top so it prints without supports. Each pocket also has a 2.2 mm poke-out hole running straight through to the rear face, also teardrop-topped.

I used Inland PETG+ (orange) and PolyLite PETG (black) on a Prusa CORE One INDX (0.4 mm nozzle, 0.2 mm layers, 2 perimeters, satin PEI build plate).

Build Guide

Insert every coupler magnet with the same pole facing out, and every adapter or direct-mount sensor top magnet with the opposite pole facing out, so any coupler fits any port. A spare magnet with one face marked makes a handy polarity checker.

Magnets are inserted from the mating face of each part. The magnet pockets have small crush ribs and are meant to be a firm press fit. Start the magnet by hand, then press the part face-down against a flat surface.

For the adapter versions, when inserting the PTFE tube, it should go entirely through the magnetic coupler and stick out about 2 mm on the other side, where it seats in a socket in the adapter. This keeps the filament from hitting rough edges where the coupler and adapter meet. The socket is 3 mm deep, so if more than that sticks out, the coupler won't sit flat. The easiest way to get the length right is to insert the tube while the coupler is attached to the adapter: push it in until it bottoms out, then pull it back about half a millimeter. (You may need to wiggle it a little to get it through the coupler.)

For the direct-mount sensor tops, keep the tube flush with the coupler's face instead. There's no socket. The sensor's filament entry leads into the channel for the ring after only about 1 mm, so a tube sticking out would poke into that channel.

Direct-Mount Sensor Tops (Experimental)

These are replacements for the INDX filament sensor top with the magnet pockets built into the face where the tubes enter. They're for setups without room for the adapter. To repeat: I haven't printed or installed any of them. The geometry has only been checked in CAD. If you try one, please post a make or a comment either way.

  • The filament path is unchanged: the filament entries, the drop-in channels for the rings, and the screw holes are identical to the original.

  • Each port has two magnets, rather than three in the adapter versions. This should make the couplers hold less strongly than on the adapter.

  • The notches and chamfer along the tube face are filled in, and there are small ears past each end because the outermost magnets need material beyond the original edges. That makes these tops wider than the stock part: about 3 mm extra per side for the 6mm versions and about 5 mm per side (with taller ears) for the 8x3mm version. Check that you have room at both ends.

  • 6x2mm, 6x2.7mm, and 6x3mm tops use the existing 6mm couplers, with only two of the coupler's three pockets used. The third (at the point of the triangle) would sit over the ring's channel, so leave it empty. Given how unreliable the 6x2mm adapter was with all three magnets, I'd expect the 6x2mm direct-mount version to be worse. I would highly suggest using 6x3mm if you're going with 6mm magnets.

  • The 8x3mm top needs the new "8x3 SensorDirect" coupler, with two magnets set nearly in a line. It is not compatible with the 8x3mm adapter in either direction. It is not symmetric: one magnet pocket (marked with a dot on the back) is slightly farther from the center than the other. The magnet with the dot must be in the "upward" position when mounted onto the sensor top (the direction with all the holes where you inserted various components of the filament sensor when assembling it).

  • The magnets sit much closer to the sensor's internals than they do with the adapter. The sensor board that detects filament sits in a slot just a few millimeters behind the tube face, and the 7x8 magnets (step 48 of chapter 4 of the INDX build guide) are behind that. My rough estimate is that the stray field at the sensor is in the same range as with the adapter in some directions and up to two to three times stronger in others, which may or may not matter. It's possible this concept doesn't work at all. Before committing, tape small stacks of magnets to the face of your existing sensor top where the pockets would be. Stacks make up for being slightly farther from the board than the real pockets. Then check that the filament sensor readings still change clearly with and without filament, and that the 7x8 magnets aren't lifted. If something is off, try the opposite polarity. You can push the magnets out from the rear face with a piece of 1.75 mm filament or a 1.5 mm hex key, with the sensor top removed from the printer.

  • The 8x3mm layout is tight. Some walls are 0.6–0.8 mm thick, and neighboring couplers have only about 0.55 mm between them. If your printer prints slightly oversized, adjacent couplers may rub.

Design Notes

I was heavily inspired in creating the magnetic coupling by Line Arc Line's Join PTFE Tubes Together Magnetically! and in particular PHRiZ's remix PTFE joiner for 8x3 magnets and PC4-M10, shown below. I ultimately found that I couldn't fit that magnet profile onto the INDX adapter, however, and so needed to design my own version. That means my magnetic couplers are not compatible with PHRiZ's. Nonetheless, I want to credit them for giving me the idea of attaching the PTFE tubes to the INDX adapter via a triangular arrangement of magnets.

Speaking of triangular, you may notice that the 6mm versions don't have equilateral triangles around the PTFE tube. That was to keep the magnets from extending below the bottom of the INDX adapter. This has the consequence of each coupler having only one correct orientation: they cannot be rotated 120° and made to fit. For the 8x3mm adapter version, I couldn't avoid extending below the bottom of the INDX adapter regardless, so I did use an equilateral triangle, and as such those couplers fit in any of three orientations.

The direct-mount tops couldn't keep the triangle. Directly above each filament entry is the channel the ring drops into, so there's no room for a magnet there. Below, the magnets can't go past the bottom face of the sensor top, which is the face it prints on. For 6mm magnets, the coupler's two lower magnets fit, so the existing couplers still work. For 8x3mm magnets, the three-magnet layout doesn't fit at all, so those use a new two-magnet layout and a new coupler.

Claude (an AI assistant) did the CAD work, modifying VertigoMakes' adapter and the INDX sensor top and modeling the couplers, while the design requirements, test prints, and fit corrections were mine. The 8x3mm and 6x2mm adapters and their couplers have been printed and tested with actual magnets, PC4-M10 fittings, and filament (with the asterisk that the 6x2mm test was largely unsuccessful); the 6x2.7mm and 6x3mm adapters/couplers, all of the direct-mount sensor tops, and the 8x3 SensorDirect coupler are untested.

Tags