1 / 5
Plant-Pot Enclosure for ReSpeaker XVF3800 4-Mic Array + XIAO ESP32S3 (Home Assistant Voice) — image 1
1 / 5

Plant-Pot Enclosure for ReSpeaker XVF3800 4-Mic Array + XIAO ESP32S3 (Home Assistant Voice)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A 118 mm puck for the round XVF3800 mic board that hides under a plant pot. One sealed duct per mic, no screws.

Rating
0 / 5
Likes
2
Downloads
3
Makes
0
Views
82
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution

A low, round enclosure for the ReSpeaker XVF3800 4-mic array with its XIAO ESP32S3, used as a Home Assistant voice satellite. It is made to disappear: a small plant pot sits on the flat top, and the microphones listen through four slots in the side of the lid.

The board is the round 100 mm version. The enclosure is two parts, 118 mm across and 18.3 mm tall, with no screws.

Features

  • Two parts: a Ø 114 × 12.3 mm base and a Ø 118 mm lid that overhangs it by 2 mm.

  • The board is located by three pins in its M2 holes, on three posts in the base. Three posts in the lid press it down from above. No screws.

  • One sealed duct per microphone: a Ø 2.5 mm well over each mic port, then a 3 × 2 mm duct to a 7 × 4 mm slot in the side of the lid. The four ducts are identical, so the four mics see the same path.

  • Flat, closed top for a plant pot or a vase. A drip groove under the lid's rim keeps drops from running back underneath.

  • A slot in the base for the USB-C power cable.

  • Three Ø 10.4 × 1 mm recesses under the base for stick-on rubber feet.

  • A centring lip on the lid drops into the base.

What you need

  • A ReSpeaker XVF3800 4-mic array with the XIAO ESP32S3 mounted underneath (the round Ø 100 mm board).

  • Four foam rings, 2 mm thick, about 2.5 mm hole and 6 mm outside, one on each mic port. The lid sits 1.5 mm above the board and squeezes them; that is what seals each duct. Foam tape and a punch work.

  • A USB-C cable and a 5 V supply.

  • Three self-adhesive rubber feet, Ø 10 mm (optional).

Good to know before you print: the lid covers the LED ring (there is no light window), and only the USB-C port is reachable. The 3.5 mm jack and the speaker connector stay inside, and there is no room for a speaker.

Print settings

  • PETG or PLA, 0.2 mm layers, 15–20 % infill, 3 perimeters.

  • No supports. The base prints upright, floor on the bed. The lid prints upside down, top face on the bed: the 3MF and STL are already oriented that way. The ducts and slots only need short bridges.

  • respeaker-pot-plateau.3mf puts both parts on one 250 × 220 plate. The separate 3MF and STL files are the same parts.

Assembly

  • Stick a foam ring on each of the four mic ports (the four small holes on the diagonals of the board).

  • Lay the board in the base, USB-C towards the slot, so the three pins go through its M2 holes.

  • Set the lid on top: the lip centres it, and its three posts land on the same holes. Turn it until the posts drop in.

  • Plug in the USB-C cable and set the plant pot on top.

The lid is not clipped or screwed: the lip, the posts and the weight on top hold it. It sheds drips, but it is not waterproof. Use a pot with a saucer and water carefully.

Every board dimension comes from Seeed's official 3D model of the board. I have not measured how the ducts change the microphones' response yet.

Designed with AI assistance (parametric CAD model).

En français

Boîtier rond (Ø 118 × 18,3 mm) pour la carte reSpeaker XVF3800 à 4 micros avec son XIAO ESP32S3, en satellite vocal Home Assistant. Un petit pot de fleur se pose sur le dessus plat ; les micros écoutent par quatre fentes sur le côté du couvercle, chacun par son propre conduit étanche (joint mousse de 2 mm sur chaque évent). Carte tenue sans vis par trois plots à ergots dans ses trous M2, couvercle centré par une lèvre et chargé par le pot. Seule la prise USB-C est accessible ; l'anneau de LED est caché. Deux pièces sans supports, déjà orientées (couvercle à l'envers).

Tags