Counting matching models…
Seeed Studio XIAO ESP32S3 Sense leverages dual-core ESP32S3 chip, supporting both Wi-Fi and BLE wireless connectivities, which allows battery charge. It integrates built-in camera sensor, digital microphone. It offers 8MB PSRAM, 8MB…
You will need: 4 M3*8 screws. An IPX/UFL to SMA connector. A 0,96 inch OLED display. The simple WiFi / Bluetooth antenna which comes with the ESP32S3 / Wio-SX1262 set. 4 wires and a soldering iron for connecting the display. Connect the…
The switch_mount_bdy_v4.3mf is an mount for switch with other dimensions than the original model.
Redesign of XIAO ESP32S3 & Wio-SX1262 case to accommodate drone usage. This setup is appx 44g total printed in PETG. This will make most drones in the sub 250g category above 250g. Please follow all laws applicable to your usage. You can…
Стационарный кѾрпус для Heltec V3-V4 c воможносью установки энкодера, клавишного переключателя, двух аккумуляторов 18650 либо один 21700. Клавишный переключатель: https://ali.click/hl1puq Рекомендации по печати: Высота слоя 0.2 Без…
The changes I made: Rotated the board & moved the USB port to the side instead of the top. (edit, both top and side versions are available) I used a 1.3 OLED instead of 0.96 (pls excuse my old eyes). Widen the case size (width and…
tight tolerances, make sure your printer is properly calibrated, 0.2mm layer height friction fit for ESP32S3 and PCM5102, box clips together both usb ports and 3.5mm audio jack exposed
This is a remix of the Seeed XIAO ESP32S3 & Wio-SX1262 to mount the antenna vertically. No supports needed I added a light pipe and wall mount.
I havce modified the Rames The Generic XIAO Sense Case (Seeed Studio XIAO ESP32S3 Sense, Camera) mount to be compatable with Michal Fanta 's Articulated arm.
This is the camera mount designed for the housing from my other project: https://www.printables.com/model/998372-seed-studio-xiao-esp32s3-sense-housing You also need to print “arm” and “base” from this project:…
A camera case for the Xiao ESP32S3 Sense to use it as a printer camera. The housing is designed so that as much air as possible can flow through and the ESP32 does not heat up too much. Additional Materials 4x Screw M3X8 There are…
A small case for the XIAO ESP32S3 Sense camera with and without a M4 mount. Suitable for the Prusa connect cam from PrusaConnect ESP32-CAM . 4 additional screws are needed for the lid. I use the flexible arm: “Demao Magnetic Soldering…
This is a wearable case designed for the Seeed Studio XIAO ESP32S3 (Sense) board. I used PLA material for the main enclosure, side cover and the stand. The wrist straps are designed to be flexible so I printed them with TPU material. This…
————Required Hardware———— Item Cost Seeed Studio XIAO ESP32 S3 Sense ~$24 IKEA Lillhult USB-A to USB-C Cable ~$5 Old Apple (iPhone) 5W USB power adapter ~$0 5 × M3-0.5x8mm Socket Cap Screws ~$4 I pick the Seeed Studio XIAO ESP32 S3 Sense…
Adsed a plate to place the antenna on.
WARNING The webcam application gets the board too hot for PLA even with the heat sink. You'll need to use PETG which has been fine for me so far in limited testing. Summary Small case for the Seeed Studio XIAO ESP32S3 Sense with a…
Uses this case https://www.printables.com/model/1043703-camera-case-xiao-esp32s3-sense and some random magnets 6.5mm magnets. Top piece is slightly modified from brunnair's design.
Created STL files of the original STP files for the tiny case for the XIAO ESP32S3 & Wio-SX1262 Meshtastic radio. So tiny but great performance!
A simple drop-in holder for the XIAO ESP32S3 & Wio-SX1262 Kit from SeeedStudio. Has a generously sized USB plug access hole in the base, and a printed ¼' thread for a standard tripod mount (20 threads per inch). Designed for windowsill /…
Snap-fit case for Seeed Studio XIAO ESP32S3 UPDATE: Added STEP file for the model for future improvements and modifications by the community. Please respect the CC Attribution Non-Commercial license. Features: Snap-fit case, no additional…
Should print fairly similar to the original design, I found my best results though at 0.16 layer height and printing the parts at an angle of XYZ 90, 45, 45. I think 0.2 layer height would work fine as well. Using the auto-orient feature…
A simple case and stand design for Sensy32 ESP32S3 IoT Dev Board. Learn more about the project here: https://sensy32.io Follow on Social Media @planmarks Website: https://planmarks.eu Support by PayPal…
A good and robust mount for a 3d printer with Alu Profiles. You can attach a GoPro or a cam case for a Xiao ESP32S3 (https://www.printables.com/model/1210524-xiao-esp32s3-cam-case) to it if you want. Print (PLA): 20% fill 0.2mm layer tree…
A Case for the Xiao ESP32S3 with the camera module. Which can be mountet on a Gopro mount or Camera Mount for Alu profile (https://www.printables.com/model/1210052-camera-mount-alu-profile-xiao-esp32s3gopro). Print (PLA): 20% fill 0,15…
A good mount for a 3d printer with Alu Profiles. You can attach a GoPro or a cam case for a Xiao ESP32S3 (https://www.printables.com/model/1210524-xiao-esp32s3-cam-case) to it if you want. Print (PLA): 20% fill 0.1mm layer tree support at…
This is a camera box designed to be used with ESP32S3 Sense (camera module). Small and sleek design with a nice fit for the USB-C connector. The cap fits on with 1/16" screws, M2 may also work.
Edited so the usb-c cable that powers it goes out straight instead of outwards. Also now has a window so you can have a heatsink on it.
XIAO ESP32S3 Dongle enclosure with Drone Bridge logo
The voice assistant housing is based on the Aga footstool designed by Chierowski.
This bracket is designed for mounting a SeeedStudio XIAO+WIO module directly below a N type RF connector (specifically, directly below a fibreglass antenna). It provides a firm support for both the connector and the board below it. The…
I like the XIAO ESP32 , I really do. It's tiny and seems to be one of the more reliable at connecting to Wi-Fi networks. That fondness for the device suddenly dies when you need to press either of the onboard buttons. They are tiny! But…
This case is designed to house the Seeed Studio XIAO ESP32S3 & Wio-SX1262 along with a LiPo 1100mAh battery (size 703048) Update 07.08.25 Added a power switch, removed the button (since it's no longer needed with the switch), and added…
What You'll Need: 18650 Battery Holder - https://amzn.to/4lnV6ej Double-sided Foam Tape - https://amzn.to/4kRXAzW Lora Antenna and IPEX-1 to SMA - https://amzn.to/3FJuHXS Or get this and use your favorite SMA antenna: IPEX-1 to SMA Female…
This is a case for waveshare ESP32S3 2.8 inch Display case. With speaker grill, screw, Memory card slot,buttons vent. https://www.waveshare.com/esp32-s3-touch-lcd-2.8.htm
Mount is: https://www.printables.com/model/1257062-quest-3-project-babble-mount
Recently I found the Xiao ESP32S3 with Wio-SX1262 LoRa hat as a good and cheap Meshtastic node for installtion at home. For some time it was just sitting in a breadboard which, the USB cable dangling between some flowsers… you know, it…
I make a few tweaks to this great case to fit my requirements. Additional parts required: 500mAh battery approx 39x17x9mm Slide switch 19.5x6mm 4x 2mm hex head bolts and heat inserts (I just pushed them it) Belt clip 2.5mm hex head bolts…
🇩🇪 Beschreibung (Deutsch) Ich habe ein Gehäuse für den Wireless Tracker (ESP32S3 + SX1262 + GPS, kompatibel mit Meshtastic und LoRaWAN) entworfen. Das Board verfügt bereits über ein integriertes GPS-Modul, es muss also kein zusätzliches…
Modelo minimalista de case para esp32s3, versão devkit1. Modelo pensado para evitar curtos ou descargas elétricas provenientes do corpo. Fiz o meu conforme imagens anexas com filamento branco no intuito de conseguir enxergar os leds…
Description While I wasn't looking to make the most unreasonably small Meshtastic node when I originally bought my XIAO ESP32S3 & Wio-SX1262 from Seeed Studio ; however, it has become quite a Quixotic quest to come up with one…
Seeed Studio XIAO ESP32S3 Plus, powered by ESP32-S3's 240MHz Xtensa 32-bit LX7 dual-core processor, brings more SMD pins to the tiny versatile XIAO ESP32S3. While maintaining all the powerful features including WiFi and BLE 5.0 wireless…
this is a model for holding a small xiao esp32s3 sense board parts used: 1x 30x30x10 5v fan 1x 10 ohm resistor (make the fan quieter) 3x M3X6 screws 2x M3x16 screws 4x M3 hex nuts 1x usb-c breakout board (for power) 1x LM2596 buck…
A simple camera arm for the Xiao ESP32S3 Sense and Prusa MK4. Used @brunnair's excellent case: https://www.printables.com/model/1043703-camera-case-xiao-esp32s3-sense And a Spring Loaded Drop in M4 T-nut M4nEs:…
This device is based on XIAO ESP32S3 and Wio-SX1262 LoRa module, making it the smallest Meshtastic Device, LoRa Sensor Node or a One Channel LoRaWAN Gateway. Coupled with an exquisite 3D - printed casing, it is equipped with an 868 -…
Seeed Studio XIAO ESP32S3 Sense leverages dual-core ESP32S3 chip, supporting both Wi-Fi and BLE wireless connectivities, which allows battery charge. It integrates built-in camera sensor, digital microphone. It offers 8MB PSRAM, 8MB…
The reset button on the XIAO-ESP32s3 needs to be pressed many times when developing firmware, but it is small and difficult to press. I created a shield to make it easier to press. I'm using Normal flow head.
LCD screen stand for ESP32-S3 4.3inch Display Development Board, 800×480, Options For Touch Function, 32-bit LX7 Dual-core Processor, Up to 240MHz Frequency, Supports WiFi & Bluetooth…
Gehäuse bestehend aus Unterteil und Oberteil, welches Platz bietet für ein 16*2 Display, ein NFC Tag Leser und einen ESP32-S3
This tiny housing for the seed studio xiao esp32 s3 sense is TINY! I didn't find a mounting option I liked, so I made my own. Features: Magnetic base: Use a 14mm round magnet to attach the foot anywhere on your printer SD card is easily…
Datalogger based on ESP32S3 with ETH POE module measures temperature and humidity, publishes it on a webserver and sends the data to a server via MQTT. PARTS: ESP32-S3 ETH Development Board https://www.waveshare.com/esp32-s3-eth.htm…
GUITION ESP32S3 4" display EU wall mount . With screw holes & center cutout for cables. Version with small cutout added as well to have a better separation between high and low voltage.
You will need: 4 M3*8 screws. An IPX/UFL to SMA connector. A 0,96 inch OLED display. The simple WiFi / Bluetooth antenna which comes with the ESP32S3 / Wio-SX1262 set. 4 wires and a soldering iron for connecting the display. Connect the…
This is a case I made to incorporate my 4.3" display as a keypad on my gate outdoors. It has a big “belly” so you can have your necessary components inside. I have: LM2596 buck converter on top 3.7V battery, small BMS with 5V output, PNP…
I really enjoy this enclosure as it is tough, light, and adaptable. I would also like to test other radios, since the case leaves some room for exploring. I used double sided tape or hot glue to keep the chips in place. EDIT: After…
You need to use support. I printed a piece with a clip on the side .
The switch_mount_bdy_v4.3mf is an mount for switch with other dimensions than the original model.
This model has some space removed internally on both the case and back cap in order to fit desired components such as a tactile button, .96 OLED Screen, and a INA219 voltage meter. The meter allows the user to view voltage state on-board…
I needed a simple case for bluetooth proxies. As I have poor signals, I wanted to place the antenna as far from the noisy/interfering electronics as possible. I do not need any of the pins, so they are not exposed. The case is snap-fit,…
A camera case for the Xiao ESP32S3 Sense but with the 2x 10x10mm Heatsinks
A clean, minimalist remix of the XIAO ESP32S3 case with all ventilation holes and patterns removed. The button holder is reinforced for added durability. Thee bottom part is slightly raised to cover the XIAO module pins without shortening…
Redesign of XIAO ESP32S3 & Wio-SX1262 case to accommodate drone usage. This setup is appx 44g total printed in PETG. This will make most drones in the sub 250g category above 250g. Please follow all laws applicable to your usage. You can…
Snap-fit ESP32-S3: slatted internal deck, USB-C left cutout, wire port + rim notches, roomy fit.
Стационарный кѾрпус для Heltec V3-V4 c воможносью установки энкодера, клавишного переключателя, двух аккумуляторов 18650 либо один 21700. Клавишный переключатель: https://ali.click/hl1puq Рекомендации по печати: Высота слоя 0.2 Без…
My design for the XIAO ESP32S3 & Wio-SX1262 Kit .. You can find many alternatives, and this is one of them, nothing special. It might meet someone’s needs. The product I received came with the pins pre-soldered, and since I didn’t know…
The changes I made: Rotated the board & moved the USB port to the side instead of the top. (edit, both top and side versions are available) I used a 1.3 OLED instead of 0.96 (pls excuse my old eyes). Widen the case size (width and…
tight tolerances, make sure your printer is properly calibrated, 0.2mm layer height friction fit for ESP32S3 and PCM5102, box clips together both usb ports and 3.5mm audio jack exposed
This is a remix of the Seeed XIAO ESP32S3 & Wio-SX1262 to mount the antenna vertically. No supports needed
This is a remix adapter that allows mounting the XIAO ESP32S3 Sense camera in case by @brunnair onto a 16 mm ball joint system with mount designed by @Sneaks. It combines two great designs into one functional setup. Features: Compatible…
I've been using jtenniswood's project for making easy LCD control panels (https://jtenniswood.github.io/espcontrol/).
I'm using the Seeed Studio XIAO ESP32S3 & Wio-SX1262 Kit for Meshtastic & LoRa as a leaf node (a node at the end of the mesh’s branches) for integration with services like Meshmonitor and Home Assistant. It's a great, minimal node when…
Made upon a request for 606090 Lipo battery support. Never printed, use with caution.
Sunton ESP32S3 8048s043c 4.3" Screen Case https://www.aliexpress.com/item/1005004788147691.html?spm=a2g0o.order_list.order_list_main.21.51981802EHw6b4 Using OpenHASP https://www.openhasp.com/0.6.3/ For the back to screw on, I used M2x12…
Sunton ESP32S3 8048S050C 5.0" Screen Case https://www.aliexpress.com/item/1005004952694042.html I printed in PETG. All credit for the original design goes to marcusone
A lightweight holder for Seeed XIAO ESP32C3 and ESP32S3 development boards, incorporating a space for the external flexible PCV aerial to sit. There are three designs: A compact holder which places the aerial under the board A holder with…
WARNING The webcam application gets the board too hot for PLA even with the heat sink. I haven't seen it obviously deform but in my case the snap fit stopped working. You'll need to use PETG (and the PETG versions of the case) which has…
Remixed with the intention to use the Xiao Sense camera as a facial tracker with Project Babble.
Please use the Onhshape link if yo uwould like the pin header extrusion to be on the bottom, I prefer having a electrically isolated" bottom.…
(Description from original author) WARNING The webcam application gets the board too hot for PLA even with the heat sink. I haven't seen it obviously deform but in my case the snap fit stopped working. You'll need to use PETG (and the…
Modified to fit a larger 160 deg FOV camera, new mounts with proper tolerance to fit an m5 bolt. (Commonly used for GoPro.) Included an extension arm I made for this and a universal mount designed to fit the Index.
This model was made for a custom PCB and housing for a small TV I built using CircuitPython, an SSD1331, and a Seeed Studio ESP32-S3. It was my first model in Solidworks - so it's very simple 😅 Meant to be used with a flat USB-C Connector…
This “Fat Man” variant expands on Rames original design by extending the back to provide a place to house the wiring for the IR LEDs as well as some small thru-holes to route those wires through to drive the LEDs, which can be press-fit…
This 3D enclosure is designed to securely house the Seed Studio XIAO ESP32S3 Sense, providing both protection and easy access to key components. The compact case ensures a snug fit while leaving essential ports and sensors exposed for…
