Counting matching models…
Thread size accommodates glass bottles typically used for vinegar, etc. Needed replacement bases for “Best-One” branded feeders which are supplied with this size threaded glass bottles. New thread hub adapted from…
Holder for 11 carbide tooling cases and two sizes of torx keys in a 3x5u base.
2x5 Gridfinity base, 2u height for 1 inch dies. Intended to be low-profile for a 1.5inch machinists toolbox drawer.
Modifications to mount my inspection microscope (ebay: https://www.ebay.com/itm/145299961892?var=444494619961 ). Additional rack height was needed due to the larger form factor of the camera optics. The hole for the modified mounting base…
Low profile gridfinity storage for a T-Slot clamping set in 2 4x7x2u Gridfinity solid base form factor. These are intended for a 7/16 T-slot set with 5/16 bolt studs in 3-8in lengths. The Strap/Step tray had extra space, so I added…
This cap and plug fit SeaQuest, US Divers, Aqualung and other BCD inflator and port as well as the quick dump valve opening on the back. The thread size is imperial 2 1/8-12. They are useful to protect threads if one removes the inflator…
Boom arm pivot replacement for the same PYLE stand in my tripod junction model. The boom pivot assembly on the OEM stand is a light gauge stamped sheet metal part which cannot apply sufficient pressure on the mount, and thus slips and…
I downloaded the original model from printables a long time ago and now cannot locate it to credit as a remix. This is a remix to resize the cardboard hub insert on the flange to fit the (current) Sunlu cardboard refill core.
Replacement for broken oem plastic part for a PYLE microphone stand bought on amazon: https://a.co/d/e0lh1k3 Requires one 8mmx1.25 heat-set inset to use the original locking knob. The OEM part had a bevel taper on the top surface which…
Magazine loader inserts for the Robins Tools magazine loader to work with the (apparently) smaller holes in the Lord Asdi magazines. Lengthened the inserts to extend through a 24mm magazine. Note this remix in ONLY the resized inserts for…
Trays to store point and cone (i am certain somebody will eventually be offended by using gender names) tap followers and the edge finders one would find in a typical set - in 1X2u and 2X3u X 2uH bases. Base generated by…
I printed on a Core One in ASA with 3 bottoms, 3 tops and 3 perimeters with 20% fill on a satin plate. Parts required for assembly: 1x M3x8 FH screw to fix crank ball to crank arm, if using crank. 2x O-rings approx 0.88od x 0.087th (dash…
Gridfinity storage trays for (2) Shars 202-5718 and (4) Starrett S190 machinists jack screw sets. Base tray is from https://gridfinity.perplexinglabs.com Printed on Core One with Sunlu PLA+ 3 bottoms, 2 perimeters, 3 tops and 15% fill and…
Square and round snap-on keycaps for 8x8mmpush on/push off locking switches. They snap on very tightly. Made specifically for Antrader switches from Amazon: https://www.amazon.com/dp/B07QVX1CKZ?ref=ppx_yo2ov_dt_b_fed_asin_title Printed on…
Improved mic boom pivot for PYLE tripod base stand (see my other models for additional replacement parts). This accommodates the standard 1/2in/12.5mm boom pole. Adjustment and locking is facilitated by a compression collet and…
These are designed to fit Shars single flute countersink sets 404-020(6,7,8) 60 deg, 82 deg, 90 deg (1.047, 1.43, 1.57 rad for metric minded :-) ). Most of my models are thin/low profile designed to fit in limited-use shallow drawers -…
Modified to assemble airbrush cradles to base with 3 M3x8 flat head screws. Added recesses to press-fit up to 3 3x12mm magnets for a magnetic base instead of table edge clamp. Original airbrush cradle mounting hole modified to accommodate…
Re-size compartments for 3/4in tooling tubes and rotate 90 degrees to allow placement of 14 tools. Maintained overall length x width so they can be stacked. Walls were not extended to form a stacking lip.
A simple 5 vial holder for Restasis. Slip fit cover protects from dust and light.
Low profile stackable storage tray for metal slotting saw blades with 1in/25mm arbor hole. Accommodates blades to approximately 4.75in diameter. Based on standard bin tray from https://gridfinity.perplexinglabs.com/
Gridfinity base to hold a set of Starrett pin vises, and a set of small (#61-80) drills.
Expanding mandrel set holder for Shars 202-5340 1/2" - 1" (#1-#5) in a Gridfinity 3x5u base.
Gridfinity storage tray for Shars 3, 6, 8, 10in machinist square set (303-6333). The 4u X 7u tray will have to be split into at least 2 pars on most printers. Dovetail joint and glue strongly advised. I made a couple of the blade recesses…
Holder for the flat-handled pin spanner for a 1/2in MT3 tailstock chuck - mine kept getting lost in the swarf tray.
Lathe centering tool with 1/2in / 12mm shank to mount in a QCTP holder - AXA or larger. This should go without saying: Print and use this tool at your own risk. If used incorrectly it can cause injury and/or damage to property. I am not…
Flush/rinse cap for SeaQuest, Aqualung, etc. BCDs.
Underwater navigation buoy/marker for shore diving. When sore diving (esp in the carribbean), one usually does a walk-in entry through the surf and in some cases swims on the surface or underwater until reaching a/the reef drop off. This…
Accessory tray for a SeaLife Micro 3.0 single light underwater camera kit. Fits snugly under the mesh net of the lid in the standard 10x10 clamshell case provided with the kit. Has recesses for the close-up and macro lenses, macro "spacer…
These are all currently available results.
