Counting matching models…
how to use Use a M4 screw with a flat underside of the head. how to print Print wings on the bottom. The only support will be in the middle. Put the mount horizontally on a mouse pad (for example), insert the screw or a cylinder in the…
how to build All sensors are from Sensirion. They all use I²C bus. The two little ones can withstand 3.3V and 5V, the PM sensor needs 5V. I choose to operate the little ones at 3.3V to minimize their heating. The SCL and SDA wires can be…
Attach with double-sided tape to whatever surface you like. The Cover version is designed for the Somrig remote with its additional cover. The No Cover versions are for the Somrig remote without the additional cover. They should also fit…
Fixes for some Brother MFC combos. Mine is an MFC-L8390CDW, a recent model for which the below problems are encountered by several users. The stopper prevent the guide from shifting during the scanning of many A4 pages, which often cause…
description I was tired that my shoes fell sideways when i took the pair next to them. This model will keep each pair in their place. No screw, no glue; no damage to the furniture. how to print As supplied; pins are indeed printed…
Print with normal snug supports, magnets holes on top, as supplied in the files. for the magnets, you'll need: • 4* disc magnets, 20mm * 5mm, with 5mm holes • 4* M4 10mm countersunk bolt screws (a bit more than 10mm can fit as the Tapo…
Prefer a rather flexible material like PETG. Simply slide from the side of the column to align its parts. Once the lock set up, pull the strip to remove.
This model is shaped specifically for my handle, which is a noname low-end one. The 195mm size is however standardized (at least in Europe). Remix the model preserving the screw holes and front plate position, adjust the back for your…
how to print 3 models provided. The screw gaps have been calculated to match HSW's lattice. • vertical: device inserted from the top (recommended for a vertical wall mount) • horizontal: device inserted from a side • both/universal: holes…
Don't trap a coin or a token in carts. This can unlock carts without getting stuck in it.
how to print Print on the supplied orientation. Enable normal snug supports (do not enable "supports on build plate only"). Remove the tiny supports with pliers. how to use magnetic version Do not use for overhead mounting. Use M3 4mm…
description Those are holders for HSW. They are lattice-aligned, meaning that they use the distances between HSW's hexagon centers as width and height. Therefore, there is no distance, or regular distance, between each holder. This is…
Warning: this is for Snapit v1 ✔, not Snapit v2 ❌. The base model is 120mm wide to fit the carrier side adapter. The 128mm wide models are to fit the width when and where the washers are in place. If you print the plates just to know…
how to build Solder an ESP32 to a Somfy Keygo series remote. Those remotes use a similar case and should have the same PCB form factor. I tested with a Keygo io model. On the back of the PCB, solder 3V3 to the metal plate and GND to the…
how to build Solder an ESP32 to a Came Top-432 remote. Those remotes use a similar case and should have the same PCB form factor. I tested with a Top-432-EE model. On the remote PCB, solder 3V3 or 5V (depending on if your remote use 2*3V…
Print on its side. No support needed. Fix with double-sided tape, like the official mount. Update 2024-04: replaced with a screw-attached one because the sun heated my door and the double-sided tape glue melted. Take a look at my 3D models.
You may want a 100% infill as this part will likely hold up high constrains.
Originally designed as a replacement for parts for folding bicycles. Use a rather flexible but strong material, like PETG, ASA, ABS. Simply insert the protector into the hexagonal nut.
Replacement for lost or broken Ikea Leirsund slat attach.
My use case: the wall switches were at the exact wrong position. Now, they are hidden behind the cabinet (and not used, thanks to domotics). The largest parts are 256 mm deep, therefore can be printed with a Bambu Lab A1/P1S/X1C. Don't…
Just push the model into your Dream cylinder case. Very sensitive to contraction. You may want to try to print the first 5mm of the model first, to check if it fit right to your vacuum cleaner. Insert into the cylinder: it should hold…
description This is a remake from scratch of @JonathanLevi 's work. https://www.printables.com/model/350716-benchy-display-for-honeycomb-storage-wall-hsw • hex inserts thickness fixed • hex inserts filled • hex inserts every other hexagon…
Prefer a rather flexible material like PETG. Simply slide from the side of the column.
Insert the original Tuya magnet part, with its tape as padding, in the print. Add the lid. Attach with double-sided tape. The hole on the bottom will help remove the magnet part by pushing it out. AliExpress links to buy the components:…
This is a lid for rudiniemeijer's case. https://www.thingiverse.com/thing:5341584 The lid itself had already been extended in height by verunka. https://www.thingiverse.com/thing:6157641 I filled the last one in order to avoid dust and…
If your bicycle dropout isn't flat, you may have difficulties to put an axle adaptor for a trailer on it. This spacer will help to stabilize and avoid damage to the frame. Use the spacer with the proper hole diameter for your axle. Edit…
Made for the OpenWrt One. The Banana Pi BPI-R64, BPI-R3, BPI-R4 have the same form factor and should be compatible as long as there is no lateral antenna. Alternatively, you can use the variants with lateral wall unfilled in order to let…
These are all currently available results.
