Counting matching models…
The original cover has some riser to keep cover of from the display window & buttons. Added those. This one also has Raymarine logo. When printing a single color printer: Slice logo.stl to .gcode Place the body just on the top of logo to…
SKaranko has made nice cherry stone removal tool. Though, I noticed a bit room tune-up the design. 1) The rounded end, friendlier for you palm 2) Thump plate 3) Hammer head a bit longer and tilted more in 4) Position slots for the hammer…
Mini size fuse tool for vehicle (car) fuses. Print on side, no support needed. Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2x0.4 Filament: any PLA Category: Hand Tools
Total length is about 80cm (mine 82cm) but it depends how thin the walls will be printed. Use wipe to avoid any stringing. Also random Z-seam alignment will help to keep the blade tubes unfused. Use 0.4mm line width to avoid over…
Lego Education kit comes with the caster & steel ball '2000702' but not in commercial one. Those aren't available in many countries so here's the next best solution. This caster is for the marble/glass ball size 16.1mm (5/8 in is a bit…
Gingerbread cookie cutter with the Scout Lily stamp. The stamp is 2mm above the cutting edge so about 3-4mm thick dough works
With this tool you can make nice decorations for the gift boxes etc. Phases, see picture titles: Two body rings bottoms up Press them together, smaller to top, see the orientation Turn unit top part up, add position 1 finger Place rest of…
Kärcher WV 6 Premium Window Vac Wall Mount for the main unit and narrow nozzle. Category: Household Supplies
The connector body for the 3-pin fan cable. This unit doesn't require any additional metal parts. Strip wire ends 5mm put them in to the holes (note the order) and bend them through the canals. The locking bar might require a bit force…
The compressor (e.g. Ryobi One+ P731) adapter for the Bravo (ver 4, used by many isup manufacture e.g. Jobe) hand pump tube. A thick isup board takes a quite long to fill up with the hand pump even with reasonable two function pump. The…
This is for 2.5" HDD caddy to the 9.5 slim DVD drive bay. Unfortunately you'll need the connection electronics as well. If you are having the 12mm HDD adapter that can donate the circuit board. The HDD & board can be secured with wide…
The Spare Dremel Driver Cap Nut for 225 Flex Shaft, 575 Angle Drive & 670 Saw The thread in this one is .28x40 in At least on my unit this a quite tight fit. Some sources indicate the thread size M8x0.75, which might be correct but and…
Webasto/Eberspacher heater hull air inlet grill for the 90mm pipe. A unit with 3mm thick face plate added Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 0% Category: Sport & Outdoors
I modified the Top & Bottom part fastening setup so that no HW needed. Category: Toy & Game Accessories
There are two versions one direct to be able to print without support, and angled one allowing the better protection for the finger (see picture to support & tip strengthening needed) The stl-files are solid. This allows better scaling…
The guide aids to drill the strait holes size 5.5, 6.0, 6.5 & 7.0 mm Elevated bottom allows you to see the actual drilling location. Print upside down (like the picture). With PLA & reasonable cooling no support needed Category: Machine…
Airbrush siphon cup 1ml (4.7 mm pipe). 2nd item with 4.6mm pipe Print multiple siphons for the each color needed. Tip: Printing with a brim or raft allow cups stand more stable on the table Category: Art Tools
The PSVR's cable hinders the head movement if it stuck somewhere. This cable clip can be adjusted for the perfect length allowing the full comfort. Obviously, the clip can be used with any headset cable. Category: Toy & Game Accessories
There was a request to implement not a Lego clutch gear on this one. I started to take 1/10s mills from here and there to fit the one and came with the idea. Now gears are modules. So here you are, U-bracket is fixed but the end gears can…
The airbrush cleaning seating and the air-vent with the filter. Pipet holder is for up to 9mm unit. The units are made for 10mm drill holes (drill guides included), though the jar lid is a bit challenging to drill. Print the vent parts…
The sharpening aid for the Dremel multi-tool to help keep 22.5 degree angle. The length of the cone 73mm. You might make it shorter down to 50mm Category: Parts
Ever happened, a fridge/freezer door is left a unnoticeable open by accident. With this unit the final push is needed close the door fully otherwise the door will stay clearly open. The Fridge_body should be mounted with the 2-side tape…
The first version has 45 angel, which might be a bit too much for some. There is a clamp with 35 angle (from vertical level) as well. Bottom_35 has also improved blade holding power via pivoting point Category: Hand Tools
The non-loose lens cap with the hinge. The hole is 21mm, you can adjust the size fitting your camera using the slicer's zoom function Category: Camera
X5S v2 comes with the 30mm radial part cooling fan. The original part has a quite small exit hole leaving the air stream limited. The part can be printed on its side, no support needed. Update v2: I did some feather testing. Narrowing the…
By the request for two pin one here it is. (though, I haven't print one - please, contribute the Make pictures. The connector body for the 2-pin fan cable. This unit doesn't require any additional metal parts. Strip wire ends 5mm put them…
Flight yaw pedals for Akaki's HOTASSet. With the bigger printer (X5S) you can print the platform Body as a one piece, for the smaller ones use the L&R halfs and the connetor bar. You'll also need extra parts: +1m length 4/2mm bowden-tube…
This is 10 tooth pinion gear for Viking/Stihl lawnmower used in many models like MB4 RT. This suits left & right Print the part with 0.6 with 0.4 mm nozzle (150%) line width to get extra strength. Also you could add 100% infill block…
The soft 'sausage' packed (600g) adhesives and sealants are significantly economical than usual the 300 ml cartridges. Though the sausages require the dedicated caulk gun, those typically can habit cartridges and the soft sausages with…
You might need to design the holders according your bike, sorry. Hopefully the .step file helps. The holders are clued to the guard and fasten with the cable ties to the bike body. You'll need the 300x300 print volume Print Settings…
This is the ski service holder fastening a slalom ski on the multi-purpose workbench. The holder will be fixed between the bench jaws at the distance of the ski binding (equal to ski boot's sole). The ski is then locked in to the table…
Typically the Foam Lance bottles come with no cap.The cap allows you to store the washing liquid in the bottle. The cap suites on the bottles with 1" pitch 4mm treading Recommend to print 45 tilted as the tightening the cap can easily…
The handicap of X5S design is lack of v-slot roller adjustment. It is essential that carriages run smoothly (no friction, no slag). Typical eccentric nuts are 6mm high but Tronxy X5S use 8.5 mm long spacers. Here is two solutions: 1)…
One major brick/block manufacture introduced this kind the differential housing in 1980's Please, notice about the possible inaccuracies with not a Lego bricks, this is recreation out from the pictures. You might want to print housing in…
Tangle Teezer Wet Detangler Brush cover Print Settings Supports: No Category: Accessories
Typically radial fans are more resistant for the back pressure. The 4020 will fit on the place of original 4010 just nice. Obviously the heat resistant filament like ABS (in the picture), PETG, ... should be used No support needed Print…
The Display4top MIG130 Plus+ welding machine comes with no means of cable management.
The male connector to fit fan connector the screw terminal. Place 0.6mm single core wires with a bit of glue. Category: 3D Printer Parts
The thinness/height adjustment transmission bevel gear replacement (the blue one) Category: Parts
And maybe a bit of paint... Category: Other
Skiing google holder elastic band holder hook for Salomon Aura downhill skiing helmet. Print Settings Rafts: No Supports: No Infill: High Filament: 3DPlastx ABS white Notes: Filament needs to be impact resistance in the frosty weather…
Two 5ii covers one solid for the flexible filament and the other one with the opening slot for hard filament like PETG, PLA, ... Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15%…
Extreme capacity battery box for the Eken (SJCam, ...) Action camera. The box will replaced the scuba housing back door and can carry up to two 18650 Li-Ion cells. They can provide up to 7000mAh (connected to parallel) power, meaning 7x…
The parts are compatible with not a Lego 'one major brick/block manufacture' and the rails 1.75mm filament. The Lift doesn't require any printing support, printed vertically. The axles (215mm/50units) (x2) should be printed on the raft to…
The phone holder kit or upgrade for https://www.thingiverse.com/thing:4076981 The kit have both strait back and cupholder one. Please, design your own stand with this kit. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No…
Lock slider for hammer drill mode selection knob. (Requires the original push spring ~4.5 x 15mm) Category: Machine Tools
It is (nearly) always a bad idea bind both ends of the Lead Screw Rod . X5S has heavy duty bearing on the top end which has a couple additional issues. Typically bearing is not seated properly by it is tilted, requires a significant force…
Use e.g. ABS 240/100C Note bit of gluing to make printing more efficient. Remix of https://www.prusaprinters.org/prints/79817-car-phoneholder-for-65-85mm-phones
Nozzle recommended tightening torque is 1.5-2.0 Nm. This torque tool add-on helps you to estimate needed force. Printing PLA, three walls and four top&bottom layers, I get ~1.75 Nm After the print you should calibrate the tool. You can…
The phone can be used both the driver as well the co-driver as the holder pivots -30,0,+30 degrees positions. Avoid need of the support the L&R brackets are printed separately and super glued. If you need change the length of the brackets…
The key is for 6x6mm axle with 14mm outer diameter. The Oras 431015 garden valve comes with T-shape key. The key supplied generates two issues: 1) kids can open the tap with ease (if you don't hide the key :-) 2) the valve can be over…
Camera mount for V-slot bar with no screws needed. Suits nicely e.g. TronXY X5S and Ender 5 type 3D printer's cubic type frame top cross bar. Category: 3D Printer Accessories
I wanted to know for what the one of the cheapest 3D printer in Ebay is capable. As the small balls are impossible to make I end up make roller bearing. The planning size is LR605 (625ZZ). (For the scaling down to 623ZZ: X&Y - 62,5% and Z…
Steering pedestal compass might missing the cover. Over the time needle housing globe gets dim because of the weathering. Plastic polisher you can recover unit in few minutes, so you don't need to get new one. This cover might suit also…
For a quite common AAA size battery unit Print Settings Supports: No Category: Outdoor & Garden
Assuming you have old laptop power bricks and/or Ryobi battery to spare. XYS3590 is affordable buck converter up to 36V/5.1A -80W This box housing two laptop power bricks 16V&19.5V = 36.5V/4.5A connected serial. The power bricks' plastic…
GIMX enables to cross use peripherals with many of gaming platforms. You'll need a dongle like this (atmega32u4) and the computer (Rasberry PI3, PC, ...) with the GIMX SW. More info: gimx.fr Category: Games
Prusa type radial fan (50mm) holder for MK10 extruder. Doesn't require additional HW (bolts or nuts) Chassis will be fasten with the extruder fan bolt (remove the 10mm nylon pipe). Additional support is given by the edge of aluminum…
Anti-wobble with the pan & tilt reduction. The carry point has 1.5mm dome to reduce effect of pivoting alignment of the treading. Category: 3D Printer Parts
Here is the lens hood to cover side light (there are two pictures to show the effect) Eken H9R has 20.8mm diameter lens, so the unit has 21m hole. You might zoom with your slicer to adjust the hole size for your meeds. The hood is for the…
Installation tool to help TruDesign true-hull installation. You can use either outside 3//8" wrench or for inside hull a pull-in line. Own size for 3/4"-2" fittings available. No support needed
Linear bearings for the CTC i3 Pro. The LM8UU with the 5mm bed, holes 32mm separation. The LM8LUU is modified a bit as well. The rails have a gap on the middle to avoid pivoting and friction reduction. Category: 3D Printer Parts
Jura coffee machine's (e.g. Xs90) milk fronther replacement. The part should be printed food-safe material with heat resistance enough. The example is printed with PETG 1mm nozzle spiral mode. After the print, two 2mm holes are drilled…
Piston's handle for the palm PETG with 0.15mm layer Category: Kitchen & Dining
The covers for the pliers jaw. Category: Hand Tools
This one has a bit wider 4040 foot than the original one for the extra stability. Category: 3D Printer Parts
Just the propeller printing requires support. Other parts with proper orientation should print OK. No glue or other HW needed. Due tight tolerances well tuned printer is required. The Pins are most critical, if needed you can zoom X&Y…
Adapter for e.g. Ryobi R181 inflator/deflator. This adapter can be used for automatic life vest testing. Place the the adapter to the curly tube of the pump, fill up the life vest via red tube, let it stand min 24h, should stay firm (- if…
The stand for the ATM unit. This allows easy position of the unit towards player in duty. The axles of the wheels, use 10x1.75mm filament pieces. There are two bodies. -Smaller fits in to the game box but seating of the unit could be…
This DualDrive Extruder is mounted as direct drive with V6 hotend. The Tronxy X5S' original metal X carriage is kept to ensure the ridged hotend installation. Though, need to drill 6mm hole for the stepper axle if direct drive…
The original bolt as holding the spool is a bit short for the wide (95mm) spools. This extension fits on the original bolt. Update: The original one the pool might hit with the bed carriage. I moved the end stopper a bit. For old design…
ABB - Jussi style Light switch cover The unit hosts the KTNNKG 433MHz Universal Wireless Remote style board (KTNN-YK86-A3) with 27A battery. Assembly: The circuit board goes back, buttons in the holder from the top after the battery…
The ski goggle's thin foam ventilation covers tend to demolish over the time. Here's the fix. Ventilation cover is printed with PLA. After the print separate a part from the bed. Heat the bed with part to 70C. This allows you the bend a…
At least on my BMG copy has nearly 2mm gap between the secondary gear and extruder body (see the picture). This allows the filament load failure if tip of the filament is even a bit wrong way curved. This add on piece fills up the gap…
As the Acetone is heavier than air the more think vapor cloud will concentrate on the bottom of the container. With this apparatus the ABS model can lowered in to a jar (height >100mm, width >70). Place a small amount acetone on the…
The RC holder for the Vesten OEM (Telefunken, Finlux, Cello, Digihome, ...) Smart 12V TVs. To avoid resonance noise use a double side tape fix the remote holder section on to the body of the TV set. Print vertically To get side level you…
Yet an other filament guide. Fits on the CTC Prusa I3 Pro or equivalent 5mm frame units. Category: 3D Printer Accessories
Tronxy has fixed some belt line issues with the X5S v2 but only to half way. The belt liner are made with the metallic bigger washer and smaller split lock washers on the both sides of bearing allowing it rotate. At least I couldn't get…
These holders have the springs to bind the glass plate in to one corner. The holders are designed for the MK2 heat bed with 213x200x3.5 (mm) glass plate. Category: 3D Printer Parts
If you like to update your printer's firmware and it doesn't work via USB port the motherboard doesn't have the bootloader installed. Also if your board just doesn't have enough program space you can upload the firmware directly via ISP…
The parallel installation of the home appliance cabinets are design so that the handles are on the middle. The reason is that the handle of the right cabinet would damage the surface of the left one. Though, always this is not the most…
The replacement tooth for Philips Blender, suites for HR2084/90 HR2084/93 HR2084/30 HR2084/00 HR2084/01 HR2094/30 HR2094/03 HR2094/00 HR2094/01 Remove the remains of the broken tooth, glue the piece to the hub e.g. using two component…
Marlin 2.0.5 config files for the Ender-3 with S-Curve, Linear Advanced & Manual Bed Leveling. Those features fit in to stock board but cutting the M503, boot screens, Icon animations, Scroll long names, Auto Temp, Power Loss Recovery...…
The tray to avoid dice run away. The graph on the table from thing:3111452 by omniparker Category: Dice
The power supplier used in the many of the 3D printers (type e.g. S-180) has very flimsy power terminal cover. The high power line terminals are just hair length away from the fingers or tools. The cover has not locking mechanism either.…
The back cover for the 2004 type LCD SDCard reader controller with the vertical connectors and the reset button on the back. The cover will be installed directly on the PCB with the display bolts, leave the nuts out. The cover is a quite…
The rubber sealant for the Deck Cable Outlet for 6, 8 & 10 mm cables. To be printed with TPU. Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.15 Filament: - TPU Notes: Print wide side down. The support ring included,…
I noticed that the original set up (with lefthand screw) puts too much pressure for the soft filamanets causing them to jam. Replacing the original screw with this one allows you to adjust the optimal extruder tension with the 4mm screw…
This one is for J-version with TTL -external triggering (FW -110 or newer) and PC connectors. The kit's mother/display board connectors are recycled for those extra connectors so unit is like 1/2 cm slimmer than standard one (see the…
The one concern of the previous design http://www.thingiverse.com/thing:2195351 was that multiple filaments couldn't be driven at the different velocities. Using the CVTs for the each filament feeder allows to tune-up the relative…
1) Case for the 'Ultra-small LM2596 supply module DC / DC BUCK 3A adjustable buck module regulator ultra LM2596S 24V switch 12V 5V 3V In Stock' 2) Bottom cover for 'Stepper Motor Parallel Module' to connect two stepper motors to the one…
The Joined PiNion Extruder, proposal for the multi/fullcolor printing. Many concepts are based on the Bowden extruders. One drawback of the Bowden is a slag hysteresis when extrude/retract. This makes the accurate color mixing difficult.…
This is based on the http://www.thingiverse.com/thing:1243891 idea. Though this is 5mm shorter to fit with the aluminum extruder holder. As this comes very near of the hot end a sheet of foil as a heat shield is recommended. The shroud…
The CTC Prusa I3 Pro Y-end stopper micro switch is a bit far away back. With this piece the whole printing area can be utilized. Plug the unit on the edge of plywood printing table matching the micro switch position Category: 3D Printer…
Use a bit flexible filament like ABS/ASA/PETG/…
The host file hadn't the movement limit values enabled there for negative and over 330 x/y movements were allowed. Changes X&Y: 0-330mm, Z:0-390mm, Bed max: 120C & some preheat value changes, default Acc & Jerk: 1000&15 In v2 extruder…
The stand for the center loudspeaker. The unit is optimized for the Panasonic 50VT60 allowing the TV's top camera usage. Print unit on the side. The fingers will be stronger on the printing tread direction. Updated version A&B: Under the…
Print two covers with suitable length (you can tune-up the length with slicer zoom, adjust only the length dimension). The example is 17cm (inner diameter) i.e. two covering 34cm queue of circuit breakers. The cover is a snug fit for 45mm…
The Bowden type filament guide to avoid filament jams for the http://www.thingiverse.com/thing:2203796 Category: 3D Printer Parts
