Counting matching models…
Expanding on the Rancho Shock Absorber bushing files I made earlier. This set includes the L1 and L3 hourglass bushing shapes as well as the LS straight bushing. Files are OpenSCAD and they allow for user specified height/width, inner…
This is a spacer for the spindle on a HollowTech-II MTB bottom bracket that allows narrowing the crank (Q-factor) by 2.5mm - 7.5mm by eliminating one or more of the outboard bearing spacers. This spacer fits over the end of the crank…
Basic 3D model (OpenSCAD) for making typical pinion or caster angle correction shims for a leaf spring vehicle. User can specify width, length, thickness, angle, center hole size and also type of mounting. First photo is an example of a…
The Mitsubishi Montero and Pajero models use 8-12 2-piece body mounts. Some later models may use 1 or 2 pair of 1-piece body mounts, not covered here. In that case, you can generally retain the original 1-piece bushings and replace the…
This is a collection of body lift components we've made over the years for the 1993-2005 (1st generation) Kia Sportage vehicles. Popular lift heights are 1-3/8" and 3". The lower heights can typically be accomplished without needing to…
This is a piece to replace a damaged hose male end on a ~2-1/2" shop vac hose. It's sized to fit inside a 54mm ID on the hose end and it has a 57mm OD for the replacement male end. Wall thickness is 1.8mm on both halves. Video on YouTube:…
A hanger or hook for the end walls of a Suncast Garden shed. Hanger attaches to the underside of the end header on the shed as shown in the photos above. To attach, slide into the recess under the header then onto the lip sticking out.…
I run Rancho shocks on my 1985 Toyota 4Runner in a custom long travel setup. As such, I needed to use a 3/4" (19mm) dia. upper mount and had to open up the ID of the 5/8"/16mm Rancho bushings to fit. That took a lot of time with a burr…
This is a housing to allow the factory "deck light" in a 1st gen Toyota 4Runner to be surface mounted instead of inset into the plastic bed side panel. This allows it to be moved from behind the roll bar and moved up higher for better…
A basic, round body lift block in OpenSCAD. Height, bolt hole diameter and outer diameter are customizable. Photo shows a 3D printed block (in ABS) on the left and a machined and painted UHMW block on the right. I have not tested any 3D…
This is a replacement lens the Toyota 4Runner deck light. Should be customizable to adapt to fit any rounded, rectangular lens held in place with 2 screws. Perfect accompaniment to the Deck Light Housing:…
Make custom fit replacement bushings for the A1, A2 and A3 platforms VW manual transmission shift linkage. First image shows several variations of of bushings printed in a Nylon filament fit on an A1 relay shaft, along with an OEM molded…
I needed a bracket to mount a 12V lighter socket in my solar garden shed. This bracket can be screwed to a flat surface and then the lighter socket fit into the hole. This is on contrast to mounting the socket into a panel, where you need…
Body mount bushings sit between the body and frame on a vehicle and help to isolate the body from the road noise and flexing of the frame. Vehicle frames are relatively flexible compared to the large sheet metal box that is the body and…
Make custom fit replacement bushings for the A2 and A3 platforms VW manual transmission shift linkage. First image shows several pair of bushings printed in a Nylon filament fit onto a 10mm dia. bolt, similar to what the relay lever…
This is a simple mounting tab for 1 or more of the ZB206+ cell discharger modules. It has a pair of hex recesses that allow the ~4.5mm hex standoffs on the bottom of the module to press into. Then the tab can be screwed or glued down to a…
A relocation plate is an easy way to relocate an axle forward of back relative to the leaf springs. The plate has a raised pin that fits into the center hole of the spring perch on the axle. Then it has one or more holes for the spring…
These are 2 parts to repair Pelouze 4010 digital scales. There are similar scales branded as Rubbermaid and Dymo. There's also a model 4040 (400 lb.) scale that looks to be quite similar. The first part is a replacement round foot for the…
This is a simple clamp adapter for the Smart & Green (S&G) LED panel light for use as a video soft light or as a general work light. Pictured light is the 25W/12"(300mm) square model: http://amzn.to/2hODbg2 The clip is designed to fit the…
This is a design for radiator brackets used to lower the radiator on a vehicle to compensate for a body lift. With a body lift, the body or cab is raised up off the frame. Since the radiator is often attached to the front of the body at…
This file is uploaded as an example of how easy it is to customize the basic drive shaft spacer OpenSCAD file. This was a request for a particular flange (unsure what vehicle this is for) and it took under 10 minutes to edit the file to…
Square/rectangular body lift blocks in OpenSCAD. Height, bolt hole diameter and outer diameter are customizable. I have not tested any 3D printed blocks on a vehicle, although some of the 3D printed TPU bushings have been used…
This is a 3D model for a basic leaf spring shackle. It can be used for many vehicle models, including Toyota Pickup/Hilux, 4Runner, T-100, Tacoma as well as Mazda B2200 and B2600 pickups. Spring shackles can be used for suspension lifts…
These sleeves can be used to modify Bilstein rear shocks for a Volvo 760 (p/n: FA-B46-0296-H2 or 24-002967) to fit the VW pickup rear axle. Bilstein never made a specific shock for the rear of the VW pickup, but they do make some strut…
Shackle spacers to fit a stock length T-100 pickup shackle for use on a Mazda B2200 pickup using the Belltech lowering springs. These springs are longer than the stock Mazda springs and thus cause the spring shackle to contact the frame.…
On the Toyota Tacoma Pickup (1995.5-2004) and 4Runner (1986-2002) and 4WD Pickup/Hilux (1986-1995) models, with suspension lifts over 2", the front CV axles will operate at an increased angle, which increases wear and tear on the CV…
In the early model A1, A2 and A3 platform VW Rabbit, Scirocco, Jetta, Convertible and Pickup/Caddy models with the 020 transaxle, adding weight to the longer sift rod can help improve shifting feel. In fact, so much so, that in the A3…
This is a spacer for a drive shaft on Dodge or Chevy vehicles with the 9-1/4" rear end that use a 3" x 3" square (4-1/4" BCD) driveshaft flange. It is designed to fit between the drive shaft and pinion or transfer case/transmission…
Blackburn Flea Tail Light Adapter to fit Topeak Explorer Rack with 50mm mounting hole spacing. This is based off the Cygolite Hotshot Pro Mount adapter, with the mounting channel widened to fit the spring clip on the Flea as well as…
I've had a number of gauges in my vehicles suffer damage over the years from UV light degrading the plastic ring behind the glass cover. This results in the glass becoming loose and rattling around as well as chunks of broken plastic…
These are all currently available results.
