Counting matching models…
I am doing an engine conversion and wanted a mock up block. Found this excellent scale model on Makerworld, checked the full size dimensions and scaled it up 284.79% to be full size. I remove all the unneeded parts and then cut away large…
Ozito/Einhell PXC tool and battery mounts. Screw holes are designed to accept 40mm 10g screws. I printed these in PETG with 30% infill and 4 walls/layers and they are very strong. Depending on the age of your tools the mounts may need…
Love the Fireball tools fixture clamps and jigs so designed and printed some basic models. Printed these in PETG-CF at 100% infill so they are reasonably strong. Used M6 heated inserts to be able to bolt tabs to them for guidance and/or…
Built my JD's Garage CNC plasma about a year ago and have changed quite a few things since then. The main change I have made is to incorporate a breakaway torch mount. This helps if the torch gets snagged on a cut and prevents damage to…
The spool roll is slightly shorted as the two uprights are now slightly closer together. Base of uprights modified to sit on top of vented riser. You need to remove the vent sliders and then this clips on top. Sits quite tightly to the…
I am doing an LS1 ZF8HP70 swap into a BMW E39 and wanted a mock up motor and trans to make initial test fitting a lot easier. Refer to my other models for the LS1. I found a good quality 4WD trans scan and some partial scan data of a 2WD…
Changing the oil on a MK7 1.4 petrol is a hassle, the filler cap is in a bad spot and any spillage gets into the coils and is hard to clean up. Also the fill rate is quite low so it's hard to moderate. Simple oil filler that securely…
The standard drier has rubber bungs in the output holes. I had a few issues where tighter wound filament spools would cause the PTFE tube from the printer to be drawn into the drier and eventually bind against the spool and cause a print…
I built a V1 JD's Garage cnc plasma a couple of years ago and made a few modifications to it. I am now building an XL and carrying over some of the modifications. This is a fully revised X and Z axis carrier with a magnetic breakaway…
Auto align onto build plate in Orca and print at 35% infill. I used PLA and it seems to last
Loved the original design however found it a bit tight to fit all the cabling into so remixed it. Modified the mount to printer assembly to add some strength. Added M4 headset inserts at all fixing points. M3 screws used to fix mount to…
Very simple wall mount bracket to suit a 21mm broom handle. Spaces the broom far enough off the wall so the head just touches the wall. Printed in TPU 95a with 35% infill. Should be easy to scale the model up and down to suit different…
Simple mount setup to adapt a BMW F30 shifter to a BMW E39 chassis - will probably suit other BMW shifters. The mount can be installed and removed without removing the centre console, only the surround needs to be removed. The top four…
Excellent original model. Nut plate with heated inserts and magnetic door handle assembly
Loved the shape of the original model but was a bit large for our outside side gate. Height is about 140mm. Screw holes are 5.5 with a 10mm countersunk head. Printed in ABS with 25% infill and 4 walls. Requires supports. The top face will…
I am doing an engine conversion and needed to be able to start the motor on the engine stand. Whipped up these parts to be able to nicely and easily mount everything to a sheet of MDF and to be able to use the 20L gas can that I had as…
5/7/25 Update - After fitting a new X carriage I had to adjust the mount slightly. Now sits further back and higher up Nebula Camera mount for the Ender3V3 Plus, should work on the regular V3 assuming it has the runout sensor. I am not…
Loved the original model so I remixed it to add heated inserts to the carriage and backing plate. There wasn't enough meat around the belt mount to put inserts so these remain as threaded into the plastic. You will also need the locking…
Simple mount designed to accomodate a 7mm cable with 3 12x3 magnet mounts. Takes 5mm x 1.5mm cable ties. Printed with 30% infill, no supports in ASA.
Two different sized braces to hold the bowden tubes at the correct locations and prevent them getting tangled I have a CoPrint 4 colour setup with the filament on rollers on each side and needed a basic way to manage the tubes to prevent…
These are all currently available results.
