Counting matching models…
This is a stackable holder meant to organize 3.5" hard disk drives. It is very quick to print, uses little filament, and helps me organize my backup and archive drives. The drives are just stacked on to of each other. No need to fasten…
This is a case for the awesome Commodore 1581 floppy disk drive replica project presented by toms01 on Forum 64 . The case closely resembles the original with some practical changes to make it more 3D-printable and to accommodate 'modern'…
This is a simple housing for 9 and 25 pin D-SUB connectors. Other sizes might follow. I needed such a housing for a current project and I couldn't find any I liked. Currently, the housing is strictly symmetrical. So you just need two…
This cartridge case is designed to fit revision 1 of the Kung Fu Flash cartridge for the Commodore 64. For the included "key caps" to fit, use tactile switches with a height of 5 mm. The right most cap shown in the photos was printed…
Please note the license for this design! It does NOT allow for commercial use. This case is designed to fit version 0.41 of the Sidekick64 cartridge for the Commodore 64 and a Raspberry Pi 3B+. Additional material required: 4 screws…
Please note the license for this design! It does NOT allow for commercial use. This case is designed to fit the short version of the Sidekick64 cartridge for the Commodore 64, made for the Raspberry Pi Zero 2. Additional material…
Please note the license for this design! It does NOT allow for commercial use. This case is designed to fit the full version of the RAD Expansion Unit cartridge for the Commodore 64, made for the Raspberry Pi 3 A+. Additional material…
This is a case for the awesome EasyFlash 3 cartridge for the Commodore 64. The case provides openings for the 3 push buttons and for the USB connector of the cartridge. Update: The new revision of the case features an additional recess…
This is a complete printable case design for the ZX81+38 replica board and the ZX81 Tactile Keyboard . For those who are interested in just the keybaord, the design files for an "external keyboard" are included as well. See my blog post…
This is a case for the Final Cartridge III+ replica as created by e5frog. Note: Depending on the size of your caps for C2 and C3 you might need to solder them lying down. If you have the 74LS133 in a socket, you should print the…
I needed new end caps for a bicycle handlebar and I couldn't find any existing designs that I liked. They all looked either too fragile, too complicated, too hard to print, or combinations of these. So I created my own simple, durable,…
Please note the license for this design! It does NOT allow for commercial use. This case is designed to fit the full version of the RAD Expansion Unit cartridge for the Commodore 64, made for the Raspberry Pi Zero 2W. Additional material…
This is an improved case for the optical read/write head for energy meters (smart meters) developed by the "Volkszähler" project in Germany. In addition to the printed parts you'll need: a ring shaped neodymium magnet, outer diameter…
This is a remake of the classic caps for user port board-edge connectors of the Commodore home computers. Each cap consist of a top and a bottom part with additional mounting holes. There are four variants with different openings for the…
These inserts can be used to key edge connectors like those required on the user port or cassette port of the Commodore 64. Properly keyed connectors will fit the correct way only and can no longer be reversed accidentally. The dimensions…
Please note the license for this design! It does NOT allow for commercial use. This is a shell to fit the original cartridge PCBs made for the Commodore 264 series of computers, i.e. the C16, C116, and the Plus/4. I tried to capture the…
Remixed, even smaller version of the "MINI bit screwdriver". Also added a version for the smaller, 4mm bits.
This is a case made to fit the size and cost reduced version of the EasyFlash 1 cartridge for the Commodore 64 created by D.Mantione in 2022. Several variations of the top shell are included, allowing you to choose whether to make LED and…
This is a replacement for the strain relief on female IDC connectors that are to be crimped onto ribbon cables. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Category: Electronics
This is a simple holder designed to fit the cheap, Xiaomi-branded Bluetooth sensors I recently purchased to integrate with my Home Assistant setup. It's modeled after this one , which I found here on Thingiverse, but it wouldn't fit my…
This is a case for the Final Expansion 3 project for the Commodore VIC20 computer. It was specifically designed to fit revision 10c of the FE3 board. I created this a few years ago but never published it until now because I always thought…
Easy to print enclosure designed to house a 5.25" disk drive, a 3.5" one, and a Greaseweazle “F7 Lightning Plus” PCB. See my blog post for details on how to build the station. Additional material required: 12 M3 screws 12 M3 nuts 4…
This is a case for the Magic Formel 2.0 cartridge that should fit the original PCB just like the excellent replica found on Github . I created this model back in 2021 and never got around to sharing it until now. Please note the license…
This is a keypad case that I made for the KIM-1 replica created by user ralf02 on forum64.de. Warning: Still work in progress and subject to change! In addition to the printable components you'll need the following: 2 keypads with 16 keys…
A simple housing for the 1541-II Power Guard project by Stefan Wagner. Requires a rubber seal ring with an outer diameter of 7-8mm. Optionally also requires two pieces of acrylic fiber 2x20mm inserted into the top part and fixed using UV…
XGecu's T48 (aka. TL866-3G) programmer is a versatile, inexpensive, and very useful device. However, the power and activity LEDs on this device are far too bright and blue. It is physically painful to look at them and it makes me fear for…
This is a case for the SD2IECplug project , which is my layout for the SD2IEC floppy drive replacement for 8 bit Commodore computers. The SD2IECplug v2 was never specifically designed to fit into an enclosure, so this case makes a few…
This is a little tool that very few people will ever need, but it's time to share it anyway. Over the past few years I've repaired a couple of Commodore 1571 floppy disk drives. I had to remove the read/write heads from the Mitsumi-built…
This is a case for Bwack's modular C64 Saver v2 . See my blog post on this build for more details. Category: Electronics
These are all currently available results.
