Counting matching models…
This print is a remix of asteven5's Resistor Storage drawers. I needed a stackable design, so I used OpenScad to add grooves to the sides, top and bottom so they can connect. The OpenScad file has been tested for properly fitting top and…
It surprises many that GMC/Chevy doesn't offer a built-in garage door opener on their Canyon or Colorado pickup trucks, even the most expensive models! Sad but true. This project uses the small inset in the dash some call the dash cubby.…
When I travel, I like to have my Hum toothbrush with me, but using the original case means you have to take the brush head off to put it away. So this 3D print allows you to store the toothbrush with the brush head attached. I used PLA on…
I have a PVC stop valve on an outdoor water line to drain the line for the winter. It is a ProLine (Mueller model 105-404). After 5 years, the handle became brittle and snapped off. This replacement faucet handle is a little larger and…
This bird spike ring is designed for the Ambient WS5000 rain gauge. I had one from the manufacturer with 16 spikes, but the birds would land in-between the spikes and deposit their droppings to plug up the gauge. This is a rather large…
This is a glue bottle holder to store glue bottles upside down. That way you can dispense glue more quickly. This model was printed in 2 hours in PLA with a 0.6mm nozzle, 0.3mm layer height, and 15% infill. An OpenScad file is included in…
I designed this to contain the pepper flakes that always were falling out of the pepper grinder onto the table. The OpenSCAD model is included in case you need to adjust for your shaker/grinder and have other preferences for other…
I couldn't find a slatwall hook to hang my round wood rasp, so here is a 3D print. There are two parts, the slatwall hook and the tool holder. The tool holder requires supports. Once printed, add some superglue and put the two parts…
My wife puts a couple of tubes of lip balm/moisturizer along with a box of mints in her Honda Passport's dash cubby, but everything was rolling around and sometimes even falling out! This tray fixes that with two slots for lip balm tubes…
Rain gauges need something to prevent birds from perching like metal prongs around the top, but some designs are not always effective. A filter can help prevent their droppings and other small wind-blown debris from getting inside the…
This model is a clamp to allow a pipe or hose to be wall or ceiling mounted. An OpenScad file is included and has the following adjustable parameters: Diameter of pipe--20mm Thickness of clamp--3mm Width of clamp--10mm Offset of pipe from…
This model prints in two halves to allow cables that have been spliced to be inserted and protected by the shell. Then the two halves can be screwed together with 4 M3x8 metric screws and hex nuts. The photo is of my prototype that is not…
Printed in PLA at 0.2mm layer height, 30% infill, and no supports. Note that the attached Gcode file is for a 0.6mm nozzle. The Openscad code is below in case you have a different size switch: // Clip for Structured Media Cabinet shelf…
A fingertip nut and washer holder is what I needed to re-assemble an expresso machine that has two, very-hard-to-reach fasteners and each includes a shouldered hex nut and a washer. My finger is large so I made an OpenSCAD model with…
This lets me connect my Fein Turbo shop vacuum to a small Rikon belt/drum sander. I included the OpenSCAD file for use in other designs. Printed in green PLA with 0.2mm layers.
I needed this to hand-tighten a hold down bolt for a spare tire. I needed to be able to tighten it pretty snugly. To create this, I imported Juradoox's knurled knob STL into OpenScad and added two wings to allow for more torque. This is…
This allows dual RCA phono jacks to be mounted inside a case where the back panel is sloped at 45 degrees. I have a Revox B790 turntable that I am refurbishing and the phono cable was hardwired. This will allow me to disconnect the phono…
The Openscad model provides a base plate with mounting tabs that can be screwed onto a remixed ESP-C3 Case bottom from @jacek. The base plate has enough internal space to enclose any dupont connectors that protrude from the bottom and a…
This model is for a bolt and nut cover to make things safer and more visible. With its rounded edges, it should help to avoid injury if someone bumps into it. The model covers a 5/8" hex nut and bolt that is 1-1/2" long. Included is the…
These are all currently available results.
