Counting matching models…
Print with 3-4 perimeters for strength and use the orientation it imports in as no supports are needed. I’d recommend PETG, PCTG, or ABS since they are more flexible than PLA or ASA and more forgiving of tight tolerances. You may need to…
My first attempt, which was oval race-track shaped with a very shallow 20 degree leading edge still managed to catch the PTFE tube. So, I modified the design to be more inspired by cow-catchers on the front of trains. I printed it in PETG…
A replacement mainboard cover for the Qidi Plus4 that allows for the use of a 92x25mm fan. I found that 92mm 24V fans were less expensive than 80mm ones so it's a good tradeoff. Here is the specific fan I used…
This part (red in the image) holds the qidi hub lower, so that you have room to add a PTFE y-splitter without trimming the stock PTFE length or creating a sharper bend. This extra distance does increase the filament change time by 5-10…
I remixed this design for better aesthetics, including properly covering the exposed wires that were visible. Please see the original design for the reasoning and results video of this fan cover modification. If you print with these…
I was having trouble obtaining a M8 100mm bolt for a reasonable price so I remixed it to use Imperial hardware. Print the aufnahme and mutter STL files from the original. For the spool holder, the following hardware is required 5/16" -…
Update: This design is now on version 3, which is even less tall that some of the previous makes. It is reliably working on my machine. After printing and installing the modified filament cutter block, I noticed that there was still a lot…
The slots were reduced to 1.2mm so that smaller desiccant, including 3A molecular sieve can be used. This design is optimized for a 0.4mm nozzle. Use arachne slicing. I printed it in PC, but PETG, PCTG, HIPS, ABS, or ASA would be good…
The original design I remixed could be printed in an orientation that provides the strongest layer adhesion on the seat-post and only a small amount of support scarring on the underside of the overhang beneath the mount. However, it…
I remixed the V7 version of Polydryer plug with PTFE passthru to be just a replacement for a lost bottom plug. I printed the one-piece design in 85A TPU with a 0.4mm nozzle, 2 perimeters, and 15% gyroid infill and it fit perfectly. Do not…
I wanted to create a simple way to organize my calibration samples, so I came up with this design. It is intended to be printed with 95A TPU on a 0.4mm nozzle. This gives it the flexibility it requires and a bit of stretchability to keep…
This is a remix to allow the Qidi Plus4 box hub bracket to attach at the same time as the spool holder. As you can see from the images, it does not block access to the screws for removing the back panel. This spool holder can use either…
I created a cap to fit into the open side of the frame for the Halloween silhoutte scenes by 3DPrintBunny listed below https://www.printables.com/model/582917-skeleton-multilayer-silhouette…
I used 95A TPU with one wall of 0.6mm width (0.4mm nozzle) and 10% gyroid infill. You will need to turn off "ensure wall thickness". Also only use 2-3 bottom layers. Orient the part like seen in the image on the orange background. Even…
Here is a replacement lid vent for the style of pyrex lids I own. Print using a 0.4mm nozzle. I used PETG but haven't tested what happens to it in the microwave yet.
Recommend 3 perimeters and a brim. If you would like the pens to fit a little bit more loosely, you can scale the model up to 100.1% or 100.2% The non-spiralized version has a little bit more extreme angles because it doesn't have the…
This model is designed to be printed with TPU and a very specific configuration of settings to keep it as soft as possible. Boot settings (already in 3mf) Use a 0.4mm nozzle with all line width set to 0.45mm (important!) Use 1 perimeter…
I purchased some misting heads for my rainbird 1/4" drip line system and they contain a 90-degree adaptor. This saved money versus the misters that come with a tube that holds an arbitrary bending shape. However, the standard stakes do…
These are all currently available results.
