Counting matching models…
This is an enhanced print bed filament dryer based on Design Prototype Test's video on the topic seen here: https://youtu.be/H1DoJxY6v_U . The air flow has to make a 90 degree turn at the top and bottom, so I used a velocity stack for the…
This is an HO scale model of the Pennsylvania Railroad viaduct over the Schuylkill River in Phoenixville, Pennsylvania. The model was developed using information from HistoricBridges.org and Google Maps in Fusion 360. For more information…
This is a set of detailed girder bridge parametric models created with OpenSCAD that can be customized by changing the length and other details, and new styles can reuse the code. It started out with a design that is common on the…
I really need this because I carry my skis 2 km to get to where I can put them on to ski. The clips hold the skis and poles together so I am just carrying one awkward thing instead of four awkward things. Its a little fidgety to put…
This is an HO scale model of the CSX railroad bridge over the Norfolk Southern railroad in Beaver County, Pennsylvania. It was built in 1909 and is still in service. The bridge can carry 4 tracks over two separate double tracks. The model…
There are several designs for nozzle scrubbers but this is compact and fits on the left side, opposite the Z end stop. My print bed thermal fuse is mounted on the right side of the bed, so I could not use the extension arm by 3DP-MAMSIH.…
Ottawa River Railroad Bridge This is an HO scale model of the two track concrete arch bridge of traditional design that carries the Norfolk Southern tracks over the Ottawa River in Toledo, Ohio. The model was developed using information…
This is a minor remix because the original did not fit my All detergent bottle. The outside diameter measured over the bottle threads is 37.5 mm on mine. I rounded off the sides, made the lip around the edge taller and reinforced the…
This is a step file for an Orange Pi 3 LTS that I made to use as reference for a project. I scavenged some parts from an Orange Pi 3 model for some of the components, but I can't figure out where I got it from. Once I find it, I will add…
This bridge is similar to the Dexter Railroad bridge shown here: https://historicbridges.org/bridges/browser/?bridgebrowser=other/dexter/ and is located just east of that bridge. It is a segmented arch stone bridge over Mill Creek in…
This is an openSCAD model that you can personalize and include a Voron logo if you want. The Customizer works well for this, just load it into openSCAD, open the customizer, and you can enter the text you want and choose if you want to…
Simple stand with access to power button. Curved sides to match MacMini aesthetic. Print with organic supports from build plate only to support finger hole. Modeled in FreeCAD.
This is a bracket for mounting the Geekworm Raspberry Pi 4 Armor Case on the din rail in a Voron printer. The case provides improved cooling of the Pi 4 without additional fans. It keeps the Raspberry Pi temperature at about 35 C with a…
Print ed with supports. It fits tight so you may want to do a little trimming on the side pegs. Pictures show a PLA+ print with .2mm layer height. Infill was 20% and 6 perimeters.
This mounts to the side of the 400 mm enclosure with M6x16 socket head screws, through the existing holes. Use 4 M3x8 screws and M3 heat sinks for the side of the panel. I didn't like the buttons on the earlier models, so this uses…
After converting from Afterburner to Stealthburner I ended up with an extra 4020 blower originally used for part cooling and with half the case removed. I decided to adapt it as a under bed fan to use heat off the bottom of the bed heater…
I made these for hiking in the mountains with my regular sunglasses. Of course there are specialized glasses for this for the professionals, but I rarely need them so I made my own. I have included the FreeCAD model. You can replace the…
This is a very minor change to cmh's design. I just removed the 3 mm in front of the fan and it significantly reduced the noise. It is still plenty strong. I printed in PLA+ with supports on the inside only, and annealed the print in my…
This is a NYC, then Penn Central concrete arch railroad bridge, described at the following link: https://historicbridges.org/bridges/browser/?bridgebrowser=michigan/oakwoodsmetroparkrr/ This bridge is located in a lowland hardwood forest,…
This design is an evolution of my previous cases for my OPi 5, starting with these features: raises the computer above the debris field on my desk makes the power, SD card and USB ports more accessible protects the SBC from damage by…
This is basically the funnel that BleedZone would provide except it is parametric and the dimensions can be changed to match what you want. And it works on road bikes with M7x0.75 thread. The OpenSCAD program is reasonably well documented…
This is a typical example of a project encompassing a dozen or so bridges built by the GTWRR in 1930 and 1931 to take the tracks northwest from Detroit. For photos see -…
This is unnecessarily fancy for a simple Pico case, but it is very robust and works well if you can print it. This is based on the tutorial for Raspberry Pi Pico Case design in Fusion 360 by Kevin McAleer on YouTube, link to video -…
I really like Boogie's Big Einsy case with BF3Design's remix, and this is just a minor remix, but with the RPi Zero W 2 it makes a big difference! By routing the LCD screen ribbon cable along the right side of the box you can mount the…
This replaces the bottom two corners and bottom plate of the steel electronics enclosure with a 75 mm deep expansion to house the on/off switch. There is also space for adding something else in the future, or just more space for wire…
Top mounting an old Android cell phone running klipperscreen has been a great addition to my Voron Trident. Having the screen above the printer means it is much more accessible than at the base of the printer, and its raised up so it…
I wanted a simple headset stand for my desk that was robust. I printed a nice design that someone else made. Sitting here looking at it, I thought I could design something a little stronger but still a simple silhouette so that it can sit…
See original for description. @ustejski made a very nice design that works well. However, I purchased the Cosori dehydrator because it was low cost and had good reviews, and had to modify the original model's shell and adapt to the center…
This is a “proof of concept” level experiment. I was visiting the California State Railroad Museum, which is in an the old Southern Pacific roundhouse, and saw the rails embedded in the floor. There is also a great model railroad exhibit…
See Dizzy Keeb's original post for more information. There is no thread on the ECAS version, so for the IDEX I just mirrored it. I did the modification in FreeCAD dev 1.1, and have attached the file if someone wants to see what I did. I…
The Formbot Voron Trident kit comes with a 3 hole cable chain and separate connectors for each device on the extruder. The Voron part for securing the cables doesn't work (its backwards and the screws are too short), so I modified…
See my first remix at https://www.prusaprinters.org/prints/147328-big-einsy-case-for-raspberry-pi-zero-w-2 for the basic description. To mount to the Bear frame use (4) M5x10 button head screws. If you are not mounting a fan, just screw…
I wanted to print the ECAS insert in TPE and when I tried the originals they were too small and the walls were too thin. So I basically copied the design and made it larger, with a small interference fit since it is made of TPE and is…
This is an adaptation of Eddie the Engineers' LED mounting, which incorporates baffles so that the LEDs are not shinning in your eyes when looking from in front of the printer. Instead of the “bead on a string” approach like the original…
There are a bunch of different EBB36 mounts which are close to what I needed but I don't like for one reason or another. So I came up with this set, which basically is a remix of the hartk design. The advantages of my remix is: Y-endstop…
This is a “work in progress”, and I will update as I work though it. I like the term “homelab”, as figuring out how to configure the file system was a major journey, with many side challenges. There are several positive features of this…
The LEDs along the top sides works nice for looking down on the build plate, but the print head itself is not well lit. This is especially a problem after I moved the printer to a location with poor ambient lighting. So I used some more…
I have several Konica Hexanon prime lenses from the 1960's and 1970's that I like to use on my Sony mirror-less camera because they are much more affordable than modern lenses for the camera with the same aperture. But I worry about…
My MIG gun slowly droops onto the floor when I roll my cart around, so I made this holder and mounted it on the welding cart. It seems to hold the gun well. The tip extends below the bottom, to reduce the potential to melt. The gun can be…
This is a mash up of the 608 bearing based spool roller that there are already many variations of. It is set up to feed out the back, so the rollers are recessed in the middle. It is still a work in progress because I have not finished…
I needed a dip stick to check the oil level in my truck differential and it was faster and cheaper to just design and print my own than go to a parts shop and hope they had one in stock.
See the original model by Voxel3D_Nederland for an explanation of the design. Since they did not include the CAD file and I wanted to be able to tune the angle, I recreated the design in FreeCAD. If you want to change it, open in FreeCAD…
This is a work in progress but I wanted to share it because it seems to work really well. I obviously have an old Samsung Galaxy S5, and I want to reuse it. It has a removable battery, and I found directions on powering it without the…
I don't know what I was doing wrong (probably just the wrong size and too thick of zip ties) but the old zip tie to guide the belt around the corner wasn't working for me. I got fed up and designed this guide. It doesn't make it easy, but…
This is a beta test of revised dimensions to fit this new model of dehydrator. My original OpenSCAD files were hard to follow, so I cleaned up the Customizer and added some descriptions. I do not have this model, so if you do and can…
I don't have a convenient place to keep the front and top panels, so these brackets hold the panels on the side of the printer. I don't try to print with high accelerations, which would be a problem because the panels wiggle. Someone else…
Added a chamfer so that the cover slides over the button/ports easier, and some ridges to make it easier to move. I printed in PCTG because the PLA was too stiff for my taste. Because the edge that its printed on is chamfered, there is…
My bicycle frame has plugged openings for future cables, and I found that one of them had fallen out. So I tried modeling a plug and printing in Filamentum Flexfill TPU 98A, and it actually worked! The walls of the plug are two perimeters…
I can't find a commercial product to do this, and found several other folks looking for it but no models. This just sits over the top of my computer, over the fan. The cat no longer lays over that warm fan outlet, with the gentle breeze…
I went down the rabbit hole of GPU supports, and found this video that describes the real problem with GPU sag- TLDR - the problem with GPU sag is that the PCB board develops a twist over time, and the solder joints between the GPU and…
I like having my Mac Mini raised a little above the surface of the table, so when I got this hub I adapted the stand for it.
These are all currently available results.
