Counting matching models…
An (experimental) A4T/XOL carriage for Monolith Gantry SCALE THE CLIPS IN Z ( in the slicer ) TO GET THE CORRECT CLIP FITMENT Information to find ideal height is found on the main Trinity Read.me , under “assembly” Uses the “universal…
Not tested again… Beefed up the DIN rails (where possible), and cut the longer ones (to be printed on an Ender 3), while maintaining strength by adding glue-in cutouts.
Tested! However, the version here is beefed up a little to add strength. Uses three “ electronics_DIN_rail_generic_mount.stl”, as for screw lengths: use whatever reaches the heat set inserts! (Remember that the Kraken is upside down when…
Tsunami An extruder that uses two sets of the HGX-lite gear kit and comes with an upgraded mounting pattern. Print settings 4 perimeters, 30% infill, no supports, ABS preferred BOM 2x HGX-lite gear kits (HGX 1.0 ONLY) 1x NEMA14 36mm round…
KNOMI V2 TESTED! KNOMI V1 NOT TESTED Designed a mount for both knomi v1 and v2. See my profile for Wide Feet Mod, which raises the printer up, and is required for knomi mount.
I decided to make the Integrated Protoxtruder again, and kept in the theme of keeping it light Credit to nhchiu: ProtoXtruder Credit to RH3D: ENDER 3 NG v1.2 - coreXY conversion Weight of printed Integrated Extruders from ABS (no gears)…
IMPORTANT IMPORTANT!!!: 12MM RODS CANNOT GO FURTHER DOWN. DOUBLR CHECK THE LENGTH TO BE EXACTLY CORRECT (SAND DOWN IF NOT) This modification requires the reprinting of 4 parts of the printer, and some new parts. This allows for the use of…
HAS BEEN TESTED! Findings: belt clamps can skip teeth, toolhead_base may violently rip apart at very high belt tensions CAUTION: TENSIONING THE BELTS TOO TIGHT MAY LEAD TO PRINTED PARTS BREAKING. WHEN TENSIONING THE BELTS PAST THE…
NOT TESTED! READ THROUGH THIS FIRST! DO NOT RUN AT SUPER HIGH TENSIONS, AF TYPE PULLEYS MAY DAMAGE THE BELTS! This mod requires: 14x 695 bearings, not flanged 2x f695 bearings, not including ones from original e3ng 2x AF type 10mm…
Not tested, yet again This simply allows for cable strain management on the toolhead, even with a round heatsink on it: Like this heatsink As with everything else I made: made in Onshape
NOT TESTED Print out the 6002 bearings from here: Print in place bearings by Jerryie | Download free STL model | Printables.com Glue the pin and hole rods together after installing bearings (glue bearings on, if desired) Uses two 4mm…
NOT TESTED YET! Knomi v2 mount, which goes in front of the hummingbird extruder. For the front half, use arachne (in the slicer), with minimum wall width of 40%, and minimum feature size of 15%. Has wire management and place to put the…
NOT TESTED These 4 pieces fix a problem that is stated by many users of e3ng, from the original ender 3 (non-pro). This is bolted on with 4x M4x16 screws and T-nuts. If desired, glue the four pieces together before installing. Assemble as…
Integrated Tsunami This is an adaptation of Tsunami to fit in the E3NG's mounting points. Notes See Tsunami for more details about the extruder Not tested yet
Replacement ducts of the ducts provided in the original. These ducts are the newer CFD tested ducts, and they have been made to be smoother and not be blocky to make it longer. (7mm longer than long ducts)
These are all currently available results.
![E3NG - Knomi v2 Mount [Hummingbird Extruder] and Extended Bambu Hotend 4020 Fan Duct](https://media.printables.com/media/prints/1033948/images/7845769_fb971539-230d-4fef-8fd6-f0abe3d1d322_30e7bb40-44f4-4782-ab5f-223618a3c9ac/screenshot-2024-10-09-080115.png)
