Counting matching models…
A Meshmixer remix of Sneq's more detailed octopus phone stand that has pockets for 8mm x3mm disc magnets. Now it stays put on my metal bedside table. These should work:…
I wanted to make the sails the player color rather than the ship. The seafairers multimaterial ship has the foam under the ship shared with the sails so that'd make the foam look funny. I edited the Tinkercad source files to remove the…
The original adapter here was unnecessarily long. To save space in my pack, I redesigned it in Fusion to be 18mm shorter. It also has some fillets and chamfers which make it less poky. Print with the narrow side down. No supports needed.…
Simple little carriers that prevent a m3 nut from sliding in a 1515 extrusion channel. They also position the nut nearer to the face of the channel so they are easier to capture by a m3 screw. The hole in the back is slightly undersized…
This is a scaled up version of my octopus phone stand with pockets for magnets. It is sized such that an Qi wireless charger and iPhone fit in the cradle. I sized it for Ubio labs 10W chargers, currently availble at Costco.…
This is a mount for the inexpensive and common DC/DC converters available on Aliexpress and Amazon . It uses the awesome life changing Wago 221 connectors. One pair of connections for the input and 4 pairs of output connections. Check'…
Beta motorcycles come with a kickstand that is WAY too short. This extension makes the bike stand up better. Best printed with LOTS of walls and 50% infill or more. An abrasion and impact resistant filament like Ninjatek's Armadillo TPU…
A simple tool to align your forks. When misaligned they can bind creating a really rough ride. Similar to the MotionPro fork alignment tool: https://www.motionpro.com/product/08-0412 To use, set the chocks of the tool to the distance…
Just a resize to 90mm wide which is about right for most cups. Also a mesh fix to the original. The 2nd pic is using thermochromic "Volcano" PLA. Print with 0.6mm layer width with 0.4mm nozzle for optimized printing speed. 0.4mm with…
The published Chube Integration model leaves a lot to be desired. This is a reverse engineer of the Chube using the published integration model from the Chube folks as a base. Everything is determined from publicly available pictures,…
Mounts for the Zumo XT (and maybe others?) and Oxford's heated grips for the AdventureSpec Mini Fairing. There's a pocket where an Airtag can be snapped into on the rear of the GPS mount. Mounts to the fairing face using existing holes in…
Something to hold the 2nd hopper from my Mazzer Mini grinder. The hole in the octopus' body is 59mm. Scale the model appropriately to fit your hopper. I lowered the original Octopus STL by 4.6 mm so it sits flat on the counter. You will…
An effector and fan shroud mount for the E3D Hemera for delta printers. This direct drive effector works quite well with well designed delta printers like the Ultibots D300VS or the various SeeMeCNC printers that use the SeeMeCNC machined…
This is a holder for a full box of Curad Alcohol Prep Pads. It holds a full box of pads. The holder is designed to mount onto an Ultibots D300VS, but could be mounted on a number of other printers. The bottom is vented so bits of plastic…
A simple tool which uses a slotted ¼" hex bit to adjust the compression clickers on a 48mm KYB shock - Adjusting them using a screwdriver is often difficult because the bars are in the way. There are 2 models here, 1 for standard 25mm…
A wall mount octopus belt rack. Good for hanging other things too. STLs for versions with 1 to 5 tentacles - monopus, dipus, tripus, quadrapus and pentapus versions. I hope I didn't butcher my greek prefixes here. Mount to the wall with…
Some mounts for 1/2" EMT rods to hold your spools. I used an old wine fridge, bought cheap on Craigslist. Refrigerators are perfect for this because they seal well and are readily available used for not much money. A rotary desiccant…
This is an improvement to the Mazzer Mini hopper that allows you to cut off the beans much lower in the grinder throat. When swapping hoppers, it greatly reduces the beans you need to fish out of the grinder, or waste by grinding through.…
MGN12 carriages for SeeMeCNC's barbells. For each carriage you will need 4 McMaster M3 Heatserts https://www.mcmaster.com/94180a331 4 M3x16 Screws (Mount to MGN12H car) 2 M3x20 Screws (Barbell) 2 M3x12 Screws (Belt Retainers) 1 M3x12…
This is a replacement drip catcher for a dehumidifer so the collected water everdrains out of the dehumidifer rather than filling up the receptacle and shutting off. I use it on my boat with the dehumidifier placed in the sink. It works…
The On/Off button of the (excellent) SKS AirChecker pressure gauge is easily pressed when in your bag. This is a simple cover to protect the On/Off button. There's a little interference nub that prevents it from falling off. Check…
Printable version of my Chube Conduction model. Some liberties taken - the main block is extended at the heater area and the thermistor is skooched up to avoid overhangs. Little nubs help the flathead screws print. F3D model:…
Fusion 360 and step files of the Triangle Labs water cooled BMG clone and assembly with a V6 and 25mm stepper. It's based on the limited TL drawings and my own metrology with calipers, so things might be off by a tad. Mounts and fan ducts…
If you have a GPS or tablet mounted at the bars, the brake lines can get in the way/snag on them. This relocates the line compliance down to the forks. This is a ground up creation of a similar product available for KTMs from Taco Moto .…
Love boat themed name tags remix. Remixed so letters are proud of the white "cloud". Can print either with a pause inserted - use Love Boat All Together.stl or With multimaterial printer such as the Mosaic Palette. Use all the remaining…
This is a jig to create and repair Tricklaser rods. Tricklaser no longer sells new rods and rod ends, so if yours breaks you need a way to repair them. The jig could also be used for making new rods if you happen to have some rod ends.…
A mount for the Mosaic Palette 2 on the Ultibots D300VS delta. It should work with any delta that has a slotted extrusion on the exterior corner of their printer. The filament can then feed from the floor, freeing up valuable desk space.…
This allows mounting of dimmer switches to control the lights of an Airstream basecamp. The interior LED lights are too bright for many times. The Dimmers - Acegoo 12V Dimmer Assembly: (Sorry i didn't take pix) Remove faceplate (a knife…
Fixed a few things in the original to make it easier and faster to print. The Fusion 360 original model contained a few things that made printing of them slower than necessary. The loft that created the shield contained some…
A simple mount to move the stock beta dash to the right, so it isn't obscured by my GPS. It may work with KTMs too if their mount holes are 80mm apart and have the same wire pigtail position. Chase the printed M6 threads with a tap.…
Simple keychain fob to mark the keys that came with your lasercube. Useful to distinguish the spares in your bowl of random keys. Either print the 3mf with a multi color printer or do filament swaps with the stl for the black (at 2mm) and…
These are all currently available results.
